Instruction/ maintenance manual of the product 20RTC Vax
Go to page of 19
20-INCH TFT-LCD MONITOR 20RTC INSTRUCTION MANUAL Please read this manual thoro ughly before us e, and ke ep it handy for future reference..
SAFETY INSTRUCTION……………………………… …………………………………….2 - 3 CAUTIONS ……………………………… ………..…… ……………… ………… ……………..4 FCC RF INTERFERENCE STATEMENT …… …… ……………………………… ………….
1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instruction s marked on the product. 4. Unplug this product from the wall outlet before cle an ing. Do not use liquid cleaners or ae rosol cleaners.
13. Do not attempt to service this product your self, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to service personnel. 14. Unplug this product from the wall ou tlet and refer servicing to qualified service personnel under the following conditions.
▶ NEVER REMOVE THE BACK COV E R Removal of the back cover should be carri ed out only by qualified personnel. ▶ DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home.
NOTE This equipment has been tested a nd found to comply with the lim its for a Cla ss B digital device, pursuant to Part 15 of the FCC Rules. T hese limits are desi gne d to provide reasonabl e protection against harmful interferen ce i n a residential installation.
A. BACK PANEL CONTROL 1 VIDEO 1 IN Composite signal Input for VIDEO 1 2 VIDEO 1 OUT Video looping output for VIDEO 1 3 V I D E O 2 I N Composite signal Input for VIDEO 2 4 V I D E O 2 O U T Video loop.
F. REMOTE CONTROLLER 1. POWER( ) Turns the power ON or O FF. There will be a few seconds delay before the d isplay ap pears. 2. SOURCE Select pc or video( PC / AV1 / AV2 / S-Video ) sources. 3. MUTE Mute the sound. 4. MENU Activates and exits the On Screen Display.
A. POWER ON/OFF( ) Turns the power ON or O FF. There will be a few seconds delay b efore the display appears. The power LED(next to the power switch) lights with gree n when the power is turned ON. The power is turned off by pressi ng the power switch again and the power LED g oes Red.
GE. VOLUME ( ) Adjust the volume / Adjust menu settings. 1. SELF-TEST DISPLAY When there is no connection at PC, the On Screen Di splay will show for 3 seconds.
: Screen : Brightness Increase or decrease the intensity of the image. : Contrast Increase or decrease the intensity (lightness or dimn ess) of the image. : H. position (PC Mode Only) Move image horizontally on screen right or left. : V. position (PC Mode Only) Move image vertically on screen up or down.
: Audio : Volume Adjust audio volume. : Equalizer (Loudspeaker Only) Boost / Cut specific frequency or compensa te for frequency distortion of the sound. Select preferred Sound setting: flat, music, movie, speech and Adjust the level of the Sound frequency in user mode.
: OSD : H. Position Move the OSD position to right( ▶ ) or left( ◀ ). : V. Position Move the OSD position to up( ▶ ) or down( ◀ ). : Transparenc y Select the OSD backgrou nd. : OSD Timer Select the OSD display timing. : Language Select a language among English, Françai s, Deutsch, Español, Danish, Italiano.
: Color (PC Mode) : Color Temp Adjust color temperature to 9300, 6500, user. (note : 9300 is factory default) : Red Adjust red color for user. : Green Adjust green color for user.
: Utility : Recall Select to reset all setting to the factory default values. : Lock Select ON or OFF (ON : Control key lock. OFF : Control key unlock) : Exit : Exit Turn off OSD Menu.
▶ PIN ASSIGNME NTS ▶ ACCESSORY 1. POWER CORD 2. USER’S MANUAL 3. PC cable 4. Remote Control 5. Batteries 6. Wall mount (Option) 7.Rack mount (Option) 15 ………………………………… .
This monitor features a power m anagement sy stem to “power d o wn” upon receipt of the VESA DPMS(The display power management si gnaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs th is signaling system through not sending horizontal, vertical, or sync signal.
▶ LCD Type 20.1 ˝ Diagon al AM-TFT (Active-Matrix) Pixel pitch(mm) : 0.51(H) X 0.51(V) BRIGHTNESS: 450cd/ ㎡ (Typical) CONTRAST RATIO: 500:1(Typical) RESPONSE TIME: Tr -5msec , Tf-11msec(Typical) ▶ RESOLUTION(H x V) 800X600 @75Hz ▶ FREQUE NCY HORIZONTAL: 31-48K Hz VERTICAL: 56 -75Hz ▶ INPUT SIGNAL VIDEO(Analog 0.
WEEE Symbols INSTRUCTION MANUAL ……………………………………… …………………………………… 18 Correct Disposal of This Product (Waste Electrical &Electronic Equipment.
An important point after buying a device Vax 20RTC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vax 20RTC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vax 20RTC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vax 20RTC you will learn all the available features of the product, as well as information on its operation. The information that you get Vax 20RTC will certainly help you make a decision on the purchase.
If you already are a holder of Vax 20RTC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vax 20RTC.
However, one of the most important roles played by the user manual is to help in solving problems with Vax 20RTC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vax 20RTC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
