Instruction/ maintenance manual of the product 17RTC Vax
Go to page of 32
17/19-INCH PREMIUM TFT-LCD MONITOR INSTRUCTION MANUAL 17RTC / 19RTC INSTRUCTION MANUAL Please read this manual thoro ughly before us e, and ke ep it handy for future reference.
SAFETY INSTRUCTION……………………………… …………………………………….2 - 3 CAUTIONS ……………………………… ………..…… ……………… ………… ……………..4 FCC RF INTERFERENCE STATEMENT …… …… ……………………………… ………….
1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instruction s marked on the product. 4. Unplug this product from the wall outlet before cle an ing. Do not use liquid cleaners or ae rosol cleaners.
Refer all servicing to service personnel. 14. Unplug this product from the wall ou tlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product.
▶ NEVER REMOVE THE BACK COV ER Removal of the back cover should be carri ed out only by qualified personnel. ▶ DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home.
NOTE This equipment has been tested a nd fou nd to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules. T hese limits are designe d to provide rea sonable protection against harmful interference i n a residential installation.
A. BOTTOM PANEL CONTROL 1. DC 12V IN 2. COMPONENT Y,Pb,Pr & SOUND L,R IN 3. AUDIO OUT 4. PC STEREO IN 5. D-SUB IN 6. DVI IN 7. HDMI IN (OPTION) B. SIDE PANEL CONTROL 1. VIDEO 1(AV1) IN 2. VIDEO 1(AV1) OUT 3. VIDEO 2(AV2) IN 4. VIDEO 2(AV2) OUT 5. S-VIDEO (Y/C) IN 6.
C. REMOTE CONTROLLER 1. POWER( ) Turns the power ON or O FF. There will be a few seconds delay before the d isplay appears. 2. SOURCE Select pc or video( AV1 / AV2 / S-Video / PC ) sources. 9. AUTO Auto geometry adjustment in PC Source. 10. MUTE Mute the sound.
D. FRONT KEY CONTROL 1. POWER ON/OFF( ) Turns the power ON or O FF. There will be a few seconds delay before the d isplay ap pears. 2. MENU / EXIT Activates and exits the On Screen Display. 3. SOURCE/SELECT Select PC or video source. Select On Screen Display menu 4 / 5.
OSD MENU DESCRIPTION A: CUSTOM MENU (Only Video mode) Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Cu stom menu. Press the up( ▲ ) / down( ▼ ) button to sel ect Custom sub menu. Press the left(◀) / right( ▶ ) button to adjust picture setting.
A: CUSTOM MENU (Only PC mode) Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Cu stom menu. Press the up( ▲ ) / down( ▼ ) button to sel ect Custom sub menu. Press (◀) / right( ▶ ) button to adjust picture setting. Press the MENU button to save.
B. Picture / Sound Menu(Only Video mode) Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Picture / Sound. Press the right( ▶ ) or ENTER button. 1. Picture Mode Press the up( ▲ ) / down( ▼ ) button to sel ect the Picture Mode.
2. Color Tone Press the up( ▲ ) / down( ▼ ) button to sel ect the Color Tone. Press the ( ▶) or ENTER button and then up( ▲ )/down( ▼ ) button to sele ct the desired color tone.
3. Mute Press the up( ▲ ) / down( ▼ ) button to select the Mute. Press the ( ▶) or ENTER button and then up( ▲ )/down( ▼ ) button t o select the desired Mute.
4. Volume Press the up( ▲ ) / down( ▼ ) button to select the Volume. Press (◀) / right( ▶ ) button to adjust Volume. Press the MENU button to save.
Press the ( ▶) or ENTER button and then up( ▲ )/down( ▼ ) button t o select the desired Size. Press the MENU button to save. 6. PC (Only PC mode) Press the up( ▲ ) / down( ▼ ) button to sel .
Press the up( ▲ ) / down( ▼ ) button to sel ect PC sub m enu Press the right( ▶ ) or ENTER button and then left (◀ ) / right( ▶ ) button to adjust PC setting. Press the MENU button to save. Auto Adjust: Auto geometry adjustment Phase: Adjust the number of horizontal picture elem ents.
1. PIP Press the up( ▲ ) / down( ▼ ) button to sel ect the PIP. Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the On or Off. Press the MENU button to save. 2. Input Source Press the up( ▲ ) / down( ▼ ) button to sel ect the Input Source.
Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Input Source. Press the MENU button to save.
Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Size. Press the MENU button to save. 4. Position Press the up( ▲ ) / down( ▼ ) button to sel ect the Positi on.
Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Position. Press the MENU button to save. 5. Swap Press the up( ▲ ) / down( ▼ ) button to sel ect the Swap.
5. Sound Select Press the up( ▲ ) / down( ▼ ) button to sel ect the Soun d Select. Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Sound Select.
D. SETUP MENU Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Setup me nu. Press the right( ▶ ) or ENTER button . 1.Reset Press ENTER button to select the reset Reset : Select to reset all setting to the factory default values.
2. Language Press the up( ▲ ) / down( ▼ ) button to sel ect the Language menu. Press the right( ▶ ) or ENTER button. Press the up( ▲ ) / down( ▼ ) button to sel ect language.
3. OSD Tone Press the up( ▲ ) / down( ▼ ) button to sel ect the OSD t one menu. Press the right( ▶ ) or ENTER button Press the up( ▲ ) / down( ▼ ) button to sel ect the desire OSD Tone.
4. Blue Screen Press the up( ▲ ) / down( ▼ ) button to sel ect the blue screen. Press the right( ▶ ) or ENTER button. Press the up( ▲ ) / down( ▼ ) button to select on or off.
5. Key Lock Press the up( ▲ ) / down( ▼ ) button to sel ect the key lock menu. Press the right( ▶ ) or ENTER button Press the up( ▲ ) / down( ▼ ) button to select on or off Press the MENU button to save.
Wall mount installation : 1) Remove the monitor stand bracket assembled with the monitor. 2) Us e the VESA standard mount ing design and the 100mm hole pattern on the back pan el to install the L CD monit or to the (Optional) mounting bracket sold separately .
▶ PIN ASSIGNMENTS ▶ ACCESSORY 1. POWER CORD 2. USER’S MANUAL 3. PC cable 4. Adaptor 5. Remote Control 6. Batteries 7. Wall mount (Option) 8. Rack mount (Option) INSTRUCTION MANUAL ………….
This monitor features a power m anagement sy stem to “power d o wn” upon receipt of the VESA DPMS(The display power management si gnaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs th is signaling system through not sending horizontal, vertical, or sync signal.
17“ 19“ 17 ˝ Diagonal AM-TFT(A ctive-Matrix) 19 ˝ Diagonal A M-TFT(Active-Matrix) Pixel pitch(mm) : 0.264(H) 0.264(V) Pixel pitch(mm) : 0.294(H) 0.
WEEE Symbols 31 ………………………………… ………………………………………… INSTRUCTION MANUAL “ Going to Sleep” message on screen Correct Disposal of This Product (Wa.
An important point after buying a device Vax 17RTC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vax 17RTC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vax 17RTC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vax 17RTC you will learn all the available features of the product, as well as information on its operation. The information that you get Vax 17RTC will certainly help you make a decision on the purchase.
If you already are a holder of Vax 17RTC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vax 17RTC.
However, one of the most important roles played by the user manual is to help in solving problems with Vax 17RTC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vax 17RTC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
