EN
Univex logo
Official user manual

Univex 358.798380

14 pages·1.6 MB·Blower·PDF·ENDEFRITNLJA
Univex 358.798380
Table of Contents 61 sections IMPORTANT MANUAL Do Not Throw Away · Operator's · Manual · ® . CRRFTSMRN · … ShowHide
IMPORTANT MANUAL Do Not Throw Awayp.1Operator'sp.1Manualp.1® . CRRFTSMRNp.112 AMP MOTOR . 165 MPH A_r Velocaty ELECTRIC BLOWER/VACp.1DOUBLE INSULATEDp.1FOR HOUSEHOLD USE ONLYp.1WARNING Ip.2IMPORTANT WARNINGS & SAFETY INSTRUCTIONSp.3MAINTENANCE SAFETYp.3SAVE THESE INSTRUCTIONSp.3PRODUCT SPECIFICATIONSp.4AMPS ................. 12p.4MODEL NUMBER: 358.798380p.4SERIAL NUMBER:p.4DATE OF PURCHASE:p.4CUSTOMER RESPONSIBILITIESp.4FULL NO YEAR WARRANTY ON SEARS BEST CRAFTSMAN ELECTRIC BLOWERNACp.4i ii iiiiiii ....... _nl iiii iii iiiii L TABLE OF CONTENTSp.5ACCESSORIESp.5HARDWARE CONTENTSp.6ASSEMBLYp.6REMOVE BLOWER FR'bM CARTONp.6BLOWER CONVERSIONp.7Figure 5 ADJUSTING THE SHOULDER STRAP ON THEp.7COLLECTION BAG (Fig. 6, & 7)p.7MINIMUM WIRE GAUGEp.7RECOMMENDATIONSp.7A.W.G.* A.W.G.* A.W.G.* A.W,G.*p.7ONIOFF SWITCHp.9TOP HANDLE /p.9COLLECTION BAGp.9SIDE HANDLEp.9INLET COVER LATCH /p.9AIR VENTSp.9FLAR E NOZZLE CONCENTRATOR NOZZLEp.9LOWER VACUUM TUBEp.9DOUBLE INSULATION CONSTRUCTIONp.9OPERATION - SAFETYp.10_ WARNINGp.10OPERATINGp.10POSITIONSp.10BLOWER VACUUMp.10STOPPING YOUR UNITp.11OPERATING YOUR UNITp.11ALWAYS WEAR EYE PROTECTION TOp.11DO MOVE VACUUM SLOWLYp.11GENERAL RECOMMENDATIONSp.12HOW TO REMOVE AN OBJECT FROM THE AIR INTAKE (Fig. 14)p.12CLEAN UNIT AND LABELSp.12CLEANING THE COLLECTION BAGp.12CHECK FOR DAMAGED/WORNPARTSp.12REMEDY SYMPTOMp.13CAUSEp.13CRRFTSMRN op.1412 AMP MOTOR 165 MPH Air Velocity E BLOWER/VACp.14Operator's Manualp.14IF YOU NEED REPAIR SERVICE OR PARTS:p.14REPAIR SERVICE 1-800-4-REPAIR (1-800-473-7247)p.14ORDERING PARTS 1-800-FON-PARTp.14(1-800-366-7278)p.14
Page 1 of the Univex 358.798380 user manual — FOR HOUSEHOLD USE ONLY
Page 1 · click to enlarge
Page 1
Univex 358.798380 — IMPORTANT MANUAL Do Not Throw Away diagram (page 1)
Fig. 1 · IMPORTANT MANUAL Do Not Throw Away

IMPORTANT MANUAL Do Not Throw Away

Operator's

Manual

Model No.

358.798380

Always Wear Eye Protection

® . CRRFTSMRN

12 AMP MOTOR . 165 MPH A_r Velocaty ELECTRIC BLOWER/VAC

I HOURS (CST) ) Mort. - Sat, 7 a.m. - 7 p.m. Sun. 10 a,m. - 7 p.m.

DOUBLE INSULATED

!_ ARNING READ THE OPERATOR'S MANUAL AND FOLLOW ALL WARNINGS AND SAFETY INSTRUCTIONS. FAILURE TO DO SO CAN RESULT IN

  • Assembly
  • Operation ° Customer Responsibilities ° Storage

SERIOUS INJURY.

FOR HOUSEHOLD USE ONLY

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

530--083224--09/29/94

Page 2 of the Univex 358.798380 user manual — WARNING I
Page 2 · click to enlarge
Page 2
Univex 358.798380 — WARNING I diagram (page 2)
Fig. 2

,,

ii iiiiiiil,llll IH I IIIl,l,ll I II I II I IIII " II II , IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

, ,,,,,,,, _

The warnings and safety instructions in this manual must befollowed to reduce the risk of fire, electric shock, or injury, and to provide reasonable safety and efficiency in using this unit. The operator is responsible for following the warnings and instructions in this manual and on the unit Read the entire Operator s Manual before assembhng and using the unit! Restrmt the use of this und to persons who read, understand, and follow the warnings and instructions in this manual and on the unit.

WARNING I

  • OPERATOR SAFETY
  • Always wear safety glasses or similar eye protection when operating, servicing, or performing maintenance onyour unit. Wearing eye protectioncan help to prevent rocks or debris from being blown or ncocheting into eyes and face which can result in blindness or serious injury.
  • Always wear a respirator or facemask when working with the unit in dusty environments.
  • Dress safely in long pants. Do not go barefoot or wear short pants, sandals, jewelry, loose clothing, or clothingwithloosely hanging straps, ties, tassels, etc.; they can be caught inmoving parts. Secure hair so itis above shoulder length.
  • Do not operate the unit when you are tired, lit, upset, or if you are under the influence of alcohol, drugs, or medication.
  • Keep loose hair, loose clothing, fingers, and all other parts of the body away from openings and moving parts.
  • Keep children, bystanders, andanimals away from the work area a minimum of 30 feet (10 meters) when starting or operating the unit.
  • inspect the area before using the unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation.
  • Restrict the use of this unitto persons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to use this unit.
  • When using the optional vacuum attachment kit, the unit is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc.. to avoid severe damage to the impeller. To avoid thepossibility of electrical shock, do not attempt to vacuum water or other liquids. ELECTRICAL SAFETY
  • outdoor appliances having electrical rating not less than the rating of the unit. The cord must be marked with the suffix "W-A" (in Canada =W"). Use a polarized cord. Make sure your extension cord is in good condition. If damaged have the cord replaced. Keep cord from heat, oil, and sharp edges. An undersized extension cord will cause a drop in line voltage resulting in toss of power and overheating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. (NOTE: Figure 7 shows the correct size to be used depending on the cord length).
  • Inspect the insulation and connectors on the unit and extension cord before each use. If there is any damage, do not use until damage is repaired by a Sears Service Center.
  • Do not pull or carry by cord; do not use cord as a handle, close a door on cord, orpullcord around sharp edges or corners. Keep cord away from heated surfaces. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
  • To reduce the possibility of the extension cord disconnecting from the unit duringoperation, tie pig tail plug and cord receptacle together as shown in Figure 8.
  • Do not use the unit if the switch does not turn the unit on and off properly. Have the unit repaired by a Sears Service Center.
  • Keep the extension cord clear of operator and obstacles at all times. Do not expose cords to heat, oil, water, or sharp edges.
  • Avoid any body contact with any grounded conductor, such as metal pipes or wire fences, to avoid the possibilityof electric shock.
  • Do not use with damaged cord or plug. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a Sears Service Center.
  • Ground fault Circuit Interrupter (GFCI) protection should be provided on the circuit oroutlet to be used for this unit. Receptacles are available having buitd-in GFCl protection and may be used for this measure of safety.
  • To reduce the risk of electrical shock this equipment has a polarized plug. This plug wil! fit in a polarized outlet or extension cord only one way. (Or_eblade is wider than the other.) If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
  • Use only a voltage supply as shown on the name plate of the unit.
  • Avoid dangerous situations. Do not use in presence of flammable liquids or gases to avoid creating a fire or explosion and/or causing damage to unit.
  • WARNING--TO REDUCE THE RISK OF ELECTRICAL SHOCK--Do not use in damp or wet locations or around swimming pools, hot tubs, etc. Do not expose to snow, rain, or water. Do not handle extension cord plug or unit with wet hands.
  • WARNING--To reduce the risk of electrical shock, use extension cords specifically marked as suitable for

i LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS -] f_l.,, ATTENTION... BECOME ALERT tH YOUR SAFETY IS INVOLVED. f

Page 3 of the Univex 358.798380 user manual — SAVE THESE INSTRUCTIONS
Page 3 · click to enlarge
Page 3
Univex 358.798380 — IMPORTANT WARNINGS & SAFETY INSTRUCTIONS diagram (page 3)
Fig. 3

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

open'ing, damaging the unit, property, or causing seri_ ous injury to bystanders or operator. • Stop the motor and disconnect the power source

  • before opening the air inlet door or attempting to insert
  • Do not overreach or use from unstable surfaces or remove the vacuum tubes. The motor must be stopped and the impeller blades no longer tuming to avoid serious injury from the rotating blades.
  • inspect the entire unit before each use for worn, loose, missing, ordamaged parts. Do not use untitthe unit is in proper working order.
  • Have all internal service performed by qualified service repair personnel to avoid creating a hazard or voiding your warranty.
  • Have all maintenance other than the recommended procedures descdbed in the Operator's Manual performed by a Sears Service Center.
  • Always see a Sears Service Center to replace a damaged impeller. Parts that are chipped, cracked, broken, or damaged in any other way can fly apart and cause sedous injury. Replace damaged parts before using the unit.
  • Never run the unit without the proper equipment attached. When used as a blower, always install a blower tube. When used as a vacuum, always install vacuum tubes and collection bag assembly.
  • Do not use any accessory or attachment other than those recommended by the manufacturer for use with your unit.
  • Use only in daylight or in good artificial light. OPERATION SAFETY

such as ladders, trees, steep slopes, rooftops, etc. Use extra care when cleaning on stairways. Keepfirm footing and balance at all times. • Never place objects inside the blower tubes; al- ways direct the blowing debris away from people, ani-

  • mals, glass, and solid objects such as trees, automobiles, wa!ts, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt people or animals, break glass, or cause other damage. Do not allow the unit to be used as a toy.
  • Never place any object in the air intake opening as this could restrict proper air flow and cause damage to the unit. ° Never run the unit without the proper equipment attached. When used as a blower, always install a blower tube. When used as a vacuum, always install vacuum tubes and collection bag assembly. Make sure the collection bag assembly is completely zipped when unit is running to avoid flying debris.
  • Never use for spreading chemicals, fertilizers, or any other substances which may contain toxic materials.
  • Avoid situations which could set the collection bag on fire. Do not vacuum discarded matches, cigars, cigarettes, or ash from fireplaces, barbecue pits, brush piles, etc. To avoid spreading fire, do not use blower near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc.
  • Always use the collection bag shoulder strap when vacuuming to avoid loss of control. ° Use only for jobs explained in this manual.
  • Keep others including children, animals, bystanders, and helpers a minimum of 30 feet (10 meters) away. Stop the motor immediately if you are approached.
  • Inspect the area before using the unit. Remove all debris and hard objects such as rocks,glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation.
  • When using the optional vacuum attachment kit, the unit is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc. to avoid severe damage to the impeller. Do not attempt to vacuum water or other liquidstoavoid electrocution.
  • Avoid accidental starting. Be sure the switch is in the "off" positionand keep your hand and fingers away from the switch while connecting the unit to the power source orwhen carrying a unit connected to the power source.
  • Turn off all controls and allow the motor to stop before disconnecting the unit from the power

MAINTENANCE SAFETY

  • Maintain the unit according to recommended procedures.
  • This unit is Double insulated. See the "DOUBLE INSULATION" section. Have all service and maintenance not explained in your operator's manual performed by a Sears Service Center to avoid creating a hazard and/or voiding your warranty. ° Disconnect from power source before servicing, cleaning, performing maintenance, or storing the unit. ° Use only genuine replacement parts as recommended by the manufacturer to avoid creating a hazard and!or voiding your warranty.
  • Never douse the unit with water or other liquids or squirt with a water hose. Clean with a damp sponge and mild soap. See =STORAGE".
  • Check air intake openings, blower tubes, elbow tube, and vacuum tubes frequently, always withthe unit stopped and the power soume disconnected. Keep vents and tubes free of debris which can accu-
  • source.
  • Disconnect the unit from the power source when not in use. Do not leave the unit when itis plugged into an outlet.
  • Avoid dangerous environments. Do not use in unventilated areas orwhere dustor explosive vapors can build up.
  • Do not set the unit on any surface except a clean, hard area while the unit is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge
  • mulate and restrict proper air flow.
  • Do not attempt to repair unit. Repairs must be performed by a Sears Service Center.
  • Do not bum, incinerate, or expose thisunitto extreme heat.
  • Store the unit unplugged in a high, cool, dry, indoors area out of the reach of children. ff situations occur which are not covered in this manual, use care and good judgmenL

if you need assistance, contact your SEARS Service Center/Department or call the CUSTOMER ASSISTANCE HOTLINE at 1-800-235-5878.

SAVE THESE INSTRUCTIONS

Page 4 of the Univex 358.798380 user manual — FULL NO YEAR WARRANTY ON SEARS BEST CRAFTSMAN ELECTRIC BLOWERNAC
Page 4 · click to enlarge
Page 4
Univex 358.798380 — PRODUCT SPECIFICATIONS diagram (page 4)
Fig. 4

CONGRATULATIONS on your purchase of a Sears Craftsman Electdc Blower/vac. It has been d(tsigned, engineered and manufactured to give you the best possible dependability and performance. Should you experience.any problems you,cannot.easily remedy, please contact your nearest Sears Service Center/Department. Sears has competent, well trained technicians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your unit properly. Always observe the "SAFETY RULES."

PRODUCT SPECIFICATIONS

VOLTAGE: 320 Volts A:C.

AMPS 12

AIR VOLUME 405 c.f.m.

AIR VELOCITY......... 165 mph

WEIGHT 7 Pounds

MODEL NUMBER: 358.798380

SERIAL NUMBER:

MANUFACTURED UNDER THE FOLLOWING U.S. PATENT: 4,325,163.

DATE OF PURCHASE:

THE MODEL AND SERIAL NUMBER WILL BE FOUND ON A DECAL ATTACHED TO THE PRODUCT.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

CUSTOMER RESPONSIBILITIES

  • Read and observe the safety rules.
  • Follow a regular schedule in maintaining, caring for, and using your unit.
  • ]Follow the instructions under "Customer Responsibilities" and "Storage" sections of this Operator's Manual.

FULL NO YEAR WARRANTY ON SEARS BEST CRAFTSMAN ELECTRIC BLOWERNAC

Ifthis Craftsman Electric BtowerNac fails to perform properly due to a defect in material or workmanship withintwo (2) years from the date of purchase, Sears will repair or replace it, free of charge.

This warranty does not cover the nylon line.

WARRANTY SERVICE 1S AVAILABLE BY RETURNING THE CRAFTSMAN ELECTRIC BLOWER/VAC TO THE NEAREST SEARS SERVICE STORE IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SEARS, ROEBUCK AND CO., D/817WA, HOFFMAN ESTATES, IL 60179

Page 5 of the Univex 358.798380 user manual — ACCESSORIES
Page 5 · click to enlarge
Page 5
Univex 358.798380 — i ii iiiiiii ....... _nl iiii iii iiiii L TABLE OF CONTENTS diagram (page 5)
Fig. 5 · i ii iiiiiii ....... _nl iiii iii iiiii L TABLE OF C…

i ii iiiiiii nl iiii iii iiiii L TABLE OF CONTENTS

J

Safety Rules 2 Product Specifications 4 Customer Responsibilities 4,12 Warranty 4 Accessories 5

Assembly 6 Operation 9 Storage 13 Trouble Shooting 13 Repair Parts Ordering/Service Back Cover

IIIIHIIIIIIIII IIIIII IIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIIIII I III INDEX

I I Hill IIIII I IIIIIII J IIIIII IIIIIIIIIII IIII IIIIIII I A O Accessories 5 Operation 9, 10, 11 Assembly 6, 7,8 Ordering Repair Parts Back Cover C S Customer Assistance Hotline Back Cover Safety Rules 2,3 Customer Responsibilities 4, 12 Specifications 4 H Stopping & Starting your Unit 10 Hardware Contents 6 K Storage 13 Know Your Electric Blowerivac 9 T M Trouble Shooting 13 Maintenance Schedule 12 W Model Number . 4 Warranty 4

ACCESSORIES

These accessories and attachments were available when the unit was originally purchased. They are also available at most Sears retail outlets and service centers. Most Sears stores can order these items for you when you provide the model number of your unit.

ACCESSORIES

Extension Cord Safety Goggles

Page 6 of the Univex 358.798380 user manual — REMOVE BLOWER FR'bM CARTON
Page 6 · click to enlarge
Page 6
Univex 358.798380 — HARDWARE CONTENTS diagram (page 6)
Fig. 6

HARDWARE CONTENTS

IL II= I Ill II

III Jllllllll III IL I IIIIIIIIIIIIIIIII IIIIIIII I II UJJ

PARTS PACKED SEPARATELY IN CARTON NOT SHOWN ACTUAL SIZE

Blower Tube Lower Vacuum Tube Flare Nozzle

ASSEMBLY

REMOVE BLOWER FR'bM CARTON

HOW TO ASSEMBLE YOUR UNIT AS A VACUUM VACUUM TUBES ASSEMBLY (Fig. 3,& 4)

  • - Remove loose parts includedwith Blower/vac.
  • Remove all packing material.
  • Check carton thoroughly for additional loose parts. ASSEMBLE YOUR UNIT INTO A BLOWER OR VACUUM MODE You can assemble your unit as a blower ora vacuum, Later you can refer to these instructions and reconfigure your unit into a different mode. The instnJctionsbelow provided information on how to assemble your unit for both configurations. HOW TO ASSEMBLE YOUR UNIT AS A BLOWER If your unit is configured in the vacuum mode, follow the following steps to prepare your blower for blower mode. If your unit is not in the vacuum mode, continue with "ATTACHING THE BLOWER TUBE & NO_LE."
  • Stop the unit.
  • Remove the vacuum tubes and collection bag.
  • Latch the inlet cover closed, and replace the screw. ATTACHING THE BLOWER TUBE & NOZZLE (Fig. 1, & 2) Remove the blower vacuum tubes and collection bag, if assembled to the unit.
  • Insert the blower tube into the bloweroutlet.
  • Turn the blowertube clockwise until it is firmly seated in the blower outlet.
  • With a slight twisting motion, slide nozzle firmly onto the end of the blower tube.

MUST BE STOPPED AND THE IMPELLER BLADES NO LONGER TURNING TO AVOID SERIOUS INJURY FROM THE ROTATING BLADES.

The lower vaccum tube is cut at an angle. Make sure the

  • label on the lower vacuum tube is aligned on the opposite side of the screw tab on the upper vacuum tube before pushing the two tubes together.
  • Push the upper and lower vacuum tubes together. o Using a Phillips screwdriver, remove the screw from the inlet cover.
  • Press the locking latch and open the inlet cover.
  • Holding inlet cover open, push assembled vacuum tubes into the opening until the locking latch engages.
  • Reinstall screw.

Locking Latcb.,.__

Inlet cove,:. _) _/_

Blower Tube ,. _ Blower Tube

Concentrator Nozzle _""_ Flare Nozzle

Show 8 more labels / short text on this page
Concentrator Nozzle · Operator's Manual · Upper Vacuum Tube · Blower Outlet / · Upper Vacuum Tube · Lower Vacuum Tube · tnlet cover · Air Intake Openin!
Page 7 of the Univex 358.798380 user manual — A.W.G.* A.W.G.* A.W.G.* A.W,G.*
Page 7 · click to enlarge
Page 7
Univex 358.798380 — BLOWER CONVERSION diagram (page 7)
Fig. 7

ASSEMBLY

L]] n , ,,n III I,,I n lU l, ,I I II I ,_TTACHING coLLEcTION BAG (Fig. 5) • Slide the opening of the collection bag over the blower outlet. Pull the strap with Velcrotightlythroughthe buckle and secure the Velcro tabs. NOTE: Make sure the strap with Velcm is located between the motor housing and the collar on the blower outlet.

BLOWER CONVERSION

° Stop unit and disconnect from power soume.

o Remove the vacuum tubes and collection bag. • Secure the inlet cover making sure that thetatch is se- curely fastened and screw is reinstalled. ° Reinstall the blower tubes. Refer to "Blower Tube Assembly" section. EXTENSION CORD (Fig. 8, & 9) Use only a voltage supply as shown on the nameplate of the unit to power your unit.

The extension cord used to reach the power source must be:

  • Specifically marked as suitable for outdoor use. The cord must be marked with the suffix "W-A. ("W in Canada).
  • Heavy enough to carry the current from the power source the full length of the extension cord to the unit. Otherwise, loss of power and overheating can occur causing damage to the unit. Refer to Figure 8 for minimum wire gauge recommendations. The cord must be marked with the proper wire gauge.

Collection Ba, Collar on Blower Outlet

Figure 5 ADJUSTING THE SHOULDER STRAP ON THE

COLLECTION BAG (Fig. 6, & 7)

- In good condition. Cord insulation must be intact with

  • Carefully loop the shoulder strap through the buckle as shown in the illustration, Notice the first in and last in is the same hole.
  • With your left hand hold the unit in an upright position, Support the lower vacuum tube on the ground, Make sure the blower outlet and collection bag are positioned on your right-hand side. ° Place the shoulder strap over your right shoulder.
  • Adjust the shoulder strap to allow a free flow of air from the blower outlet. If the collection bag is kinked, the unit wil! not operate properly. NOTE; The shoulder strap is designed to position the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit.

no cracks or deterioration, Plug connectors must be un- damaged. Secure extension cord to unit as follows: • Tie cord from unit to extension cord.

° Plug cord from unit into extension cord. To reduce the risk of electric shock, this unit has a polarized plug (one blade is wider than the other). This plug will fit ina polarized extension cord only one way, If the plug does not fit fully into the extension cord, reverse the cord.

If it still does not fit, make sure you have a polarized extension cord. if the extension cord does not fit into the outlet, reverse the cord. If it still does not fit into the outlet, contact a qualifiedelectrician to installthe proper outlet. Do not change the plugor socket of the unitor extension cord in any way.

MINIMUM WIRE GAUGE

RECOMMENDATIONS

VOLTS 25 FT. 50 FT. 100 FT. 150 FT.

120 16 16 14 12

A.W.G.* A.W.G.* A.W.G.* A.W,G.*

*American Wire Gauge Figure 8

Shoulder strap on right shoulder Free flow of air. No kinks In collection bag

Show 5 more labels / short text on this page
Strap with Velcro · Last In · First lnJ_ · Extension Cord · Cord from Unit
Page 8 of the Univex 358.798380 user manual — ....................................................................................... ASSEMBLY
Page 8 · click to enlarge
Page 8
Univex 358.798380 — BLOWER CONVERSION diagram (page 8)
Fig. 8

ASSEMBLY

CHECK LIST ° Check all.fasteners. Make sure they are tight and there are no loose parts. • Make sure the blowertube isfirmly seated in the blower outlet.

  • If you are using the unit as a blower, make sure the inlet cover is latched and the screw is fastened.

° In blower mode, check to insure the nozzle is securely seated in the blower tube.

  • If you are using your unit as a vacuum, make sure the vaccum tubes are firmly connected, and positioned as shown in the assembly illustrations with the screw securely fastened.
  • Make sure the collection bag is correctly adjusted with the shoulder strap on your left shoulder. ° Make sure your extension cord is marked with a suffix of "W-A". ("W" in Canada).

ii jilL //

Page 9 of the Univex 358.798380 user manual — DOUBLE INSULATION CONSTRUCTION
Page 9 · click to enlarge
Page 9
Univex 358.798380 — ONIOFF SWITCH diagram (page 9)
Fig. 9

KNOW YOUR ELECTRIC BLOWER (Fig. 10) READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING "fOUR ELECTRIC BLOWER. Compare the illustrationswithyour unit to famUiadze yourself with the location of the various controls and adjustments. Save this manual for future reference.

ONIOFF SWITCH

TOP HANDLE /

COLLECTION BAG

SIDE HANDLE

INLET COVER LATCH /

AIR VENTS

U

FLAR E NOZZLE CONCENTRATOR NOZZLE

LOWER VACUUM TUBE

The SIDE HANDLE is used to hold the unit during Vacuum mode.

The ONIOFF SWITCH is used to turn on the unit.

The INLET COVER LATCH is used to open the inlet cover for attaching Upper Vacuum Tube. The TOP HANDLE is used to hold the unit during the Blower and Vacuum mode.

The FLARE NOZZLE is use to direct the flow of air into a larger area than the CONCENTRATOR NOZZLE. The CONCENTRATOR NOZZLE is use to direct the flow of air into a concentrated area.

i ii rl:

DOUBLE INSULATION CONSTRUCTION

This unit is Double Insulated to help protect against electric shock. Double insulationconstruction consists of two separate "layers" of electrical insulation instead of grounding.

_ WARNING ALL ELECTRICAL REPAIRS TO THIS UNIT, INCLUDING HOUSING, SWlTCH, i MOTOR, ETC., MUST BE DIAGNOSED AND REPAIRED BY QUALIFIED SER-;; VICE PERSONNEL. REPLACEMENT PARTS FOR A DOUBLE INSULATED AP- PLIANCE MUST BE IDENTICAL TO THE J PARTS THEY REPLACE. A DOUBLE IN- SULATED APPLIANCE IS MARKED WITH THE WORDS "DOUBLE INSULA- TION" OR "DOUBLE INSULATED". THE SYMBOL (SQUARE WITHIN A SQUARE)

Tools and appliances build with a double insulation system are not intended to be grounded. No grounding means is provided on this unit, nor should a means of grounding be added to this unit. As a result, the extension cord used with your unit can be plugged into anystandard 120 volt electrical outlet.

Safety precautions must be observed when operating any electrical tool. The double insulation system only pro- vides added protection against in}ury resulting from an inter-

[] MAY ALSO BE MARKED ON THE AP- PLIANCE. FAILURE TO HAVE THE UNIT REPAIRED BY QUALIFIED SERVICE PERSONNEL CAN CAUSE THE DOUBLE INSULATIONS CONSTRUC- TION TO BECOME INEFFECTIVE AND RESULT IN SERIOUS INJURY.

nal electrical insulation failure.

Page 10 of the Univex 358.798380 user manual — OPERATING
Page 10 · click to enlarge
Page 10
Univex 358.798380 — OPERATION - SAFETY diagram (page 10)
Fig. 10

OPERATION - SAFETY

O'PERATOR SAFETY' "

° Dress safely in long pants. Do notgo barefoot orwear short pants, sandals, jewelry, loose clothing, or clothing with Ioose!y hanging strops, ties, tassels, etc.; they can be caught in moving parts. Secure hair so it is above shoulder length. Use of rubber gloves is recommended. • Check the unit before each operation. Look for worn, loose, missing, ordamaged parts. Do not use the unitun- til it is in proper working order.

DO NOT ASSEMBEEOR'DISASSEMBLE THE VACUUM TUBES WHILE THE UNIT IS RUNNING, INSERTING OR REMOVING THE VACUUM= TUBES WHILE THE UNIT IS RUNNING CAN RESULTIN SERIOUS INJURY. ALWAYSSTOP THE UNIT AND DISCONNECT THE POWER SOURCE BEFORE UNCLOGGING THE UNIT OR PERFORMING ANY MAINTENANCE ON THE COLLECTION BAG.

_ WARNING

° inspect area before operating unit. Remove all debris and objects suchas rocks, glass, wire, large sticks, etc. that can cause damage during operation.

  • Keep children, bystanders, and animals safely away. Before starting the unit and during operation, make certain children, people, and animals are a minimum of 30 feet away from the work area.

DO NOT USE THE UNIT WITHOUT THE BLOWER TUBES PROPERLY ATTACHED TO AVOID FLYING DEBRIS AND/OR IMPELLER CONTACT WHICH CAN CAUSE SERIOUS INJURY.

  • Check air intake opening, blower tubes, and vacuum tubes frequently, always with the motor stopped and the power source disconnected. Keep vents and discharge tubes free from debriswhich can accumulate and restrict

ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES AND FACE WHICH CAN RESULT IN BLINDNESS OR SERIOUS INJURY.

proper air flow.

  • Do not ptug unit into any receptacle other than a normal 120 volt household outlet.
  • Never immerse any part of the unit into any liquid,

DO NOT USE THE UNIT AS A VACUUM WITHOUT THE VACUUM TUBES AND COLLECTION BAG PROPERLY ATTACHED TO AVOID FLYING DEBRIS AND/OR IMPELLER CONTACT WHICH CAN CAUSE SERIOUS INJURY. ALWAYS MAKE SURE THE COLLECTION BAG IS COMPLETELY ZIPPED BEFORE THE UNIT IS STARTED.

  • Use the correct operating position. Figure 11. Do not overreach or use from unstable surfaces such as ladders, trees, steep slopes, roof tops, etc. Keep firm footing and balance at all times.

° Never place objects inside the blower tubes; always direct blowing debris away from people, animals, glass,

and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to dcochet which may hurt people or animals,

DO NOT ATTEMPT TO VACUUM WATER OR OTHER LIQUIDSTO AVOID ELECTROCUTION.

break glass, or cause other damage.

° When using your unit as a vacuum, always use collec- tion bag shoulder strap to avoid loss of control.

As a blower, the unit is designed to sweep debris, grass, straw, leaves, or small twigs. Never use for spreading or misting chemicals, fertilizers, or any other materials which may contain toxic substances. As a vacuum, the unit is designed to pickup dry material such as leaves, grass, small twigs, and bits of paper. Do not attempt to vacuum stones, gravel, metal, broken glass, or any other debris which may cause damage to the impeller. Do not attempt to vacuum

  • Never run the unit without the proper equipment attached. When using your unit as a blower, always install blower tubes. When using your unit with the optional vacuum attachment, always install vacuum tubes and collection bag assembly. Make sure collection

bag assembly is completely zipped.

  • Adjust shoulder strap and waist belt to fit securely before operation of unit.

snow, water, orany other liquids: vacuuming water or other liquidswill cause damage to the unit. Avoid situations that couldcatch the collectionbag on fire. Do notoperate near an open flame. Do not vacuum discarded matches, cigars, or cigarettes, or ash from fireplaces, barbecue pits, brush piles, etc.

OPERATING

POSITIONS

BLOWER VACUUM

  • Read your Operator's Manual. Make sure you completely understand and can follow all warnings and safety

instructionsin the manual before operating the unit.

  • Always wear eye protection when operating, servicing, or performing maintenance to prevent rocks or debris from being blown or ricocheting into eyes and face which can result in blindness or other serious injury.
  • Always wear a respirator or face mask when working in dusty environments.
Page 11 of the Univex 358.798380 user manual — DO MOVE VACUUM SLOWLY
Page 11 · click to enlarge
Page 11
Univex 358.798380 — STOPPING YOUR UNIT diagram (page 11)
Fig. 11

STOPPING YOUR UNIT

USING YOUR UNIT AS A VACUUM (Fig. 12) Use your unit as a vacuum to pick up dry matedal such as leaves, grass, small twigs, and bits of paper.

  • Slide the switch to the OFF position. STARTING YOUR UNIT
  • Slide the switch to the LOW or HIGH position.
  • For best results operate your unit at high speed, while using as a vacuum.
  • Move the unit slowly back and forth over debds to be vacuumed. Avoid forcing the vacuum tubes into a pile of debris as this can clog the unit.

OPERATING YOUR UNIT

  • Keep the vacuum tube about an inch above the ground.
  • Stop the unit and disconnect the power source.
  • Wait until the impeller has completely stopped turning, then remove the vacuum tubes.

° Carefully reach into the vacuum opening and clear out debris.

ALWAYS WEAR EYE PROTECTION TO

PREVENT ROCKS OR DEBRIS FROM i BEING BLOWN OR RICOCHETING INTO THE EYES AND FACE WHICH CAN RESULT IN BLINDNESS OR SERIOUS INJURY.

° You must properly empty and maintain the collection bag to avoid deterioration and obstruction of air flow.

  • Remove the collection bag from the unit and empty after each use. Do not store collection bag containing leaves, grass, etc.

USING YOUR UNIT AS A BLOWER (Fig. 11) Use your unit as a blower for sweeping debris or grass clippings from driveways, sidewalks, patios, etc.

° Wash the collection bag once a year. Remove the bag from the blower and turn the bag inside out. Wash the bag with a water hose. Allow the bag to hang and dry before you reuse the bag.

Use your unit as a blower for blowing grass clippings, straw, or leaves into piles, or removing debris from comers, around joints, and between bricks.

- Direct air flow by directing the nozzle down orto one side. Always work away from solid objects such as walks, large stones, automobiles, and fences.

DO NOT FORCE INTO PILE.

DO MOVE VACUUM SLOWLY

- Clean comers by starting in comers and moving outward to straight areas to prevent an accumulation of debris which could fly into face.

BACK AND FORTH.

  • Be careful when working near plants. The force of the air could damage tender plants.

Vacuum Operating Position

Page 12 of the Univex 358.798380 user manual — CHECK FOR DAMAGED/WORNPARTS
Page 12 · click to enlarge
Page 12
Univex 358.798380 — GENERAL RECOMMENDATIONS diagram (page 12)
Fig. 12

,I,L,ILILIIllJIlll ' II,,lllllll,lllll I Illll Illlllllll I I , CUSTOMER RESPONSIBILITIES

iiii illl i =l MAINTENANCE SCHEDULE

Fill in dates as you complete regular service.

Check for damaged or worn parts.

,,,,,,,,,,,, Clean unit and labels.

i ,,,,,,,, Check for loose fasteners and parts.

Wash collection bag.

,,,,,,,,,,

GENERAL RECOMMENDATIONS

HOW TO REMOVE AN OBJECT FROM THE AIR INTAKE (Fig. 14)

The warranty on this unit does not cover itoms that have

if an object is drawn into the unit through the air intake, do the following:

been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual.

  • Push the switch to the OFF position and disconnect cord from the power source.
  • Remove the vacuum tubes.

Some adjustments will need to be made periodically to properly maintain your unit.

  • Locate and remove the object(s).

All adjustments in the "Service and Adjustments" section of this manual should be checked at lease once each season.

  • Inspect the impeller for cracks. If cracked or damaged, DO NOT use the unit. Have impeller replaced by your Sears Service Center. DO NOT attempt to replace it yourself.

Follow the maintenance schedule in this manual,

Vacuum Air Intake Inlet Cover

Air Vents Figure 14

CLEAN UNIT AND LABELS

  • Clean the unit using a damp cloth with a mild detergent.

CLEANING THE COLLECTION BAG

  • Wipe off the unit with a clean dry cloth.
  • Keep air vents and air intake free from debris at all times. BEFORE EACH USE

The collection bag must be properly emptied and maintained to avoid deterioration and obstruction of air flow which will reduce the performance of your unit.

CHECK FOR DAMAGED/WORNPARTS

  • Remove the bag and empty after each use. DO NOT store the bag leaves, grass, or debds.
  • Replace blower nozzles that are bent, warped, cracked,

or damaged in any way.

  • Wash the bag once a year by turning inside out and washing with a water hose. Be sure to let bag dry completely before re-using the unit.
  • Replace vacuum tubes that are bent, warped, cracked, or damaged in any way.
  • Inspect impeller for cracks. CHECK FOR LOOSE FASTENERS/PARTS
  • Inspect blower tube. Make sure tube is secure to the blower outlet.

Release Locking

Page 13 of the Univex 358.798380 user manual — REMEDY SYMPTOM
Page 13 · click to enlarge
Page 13
Univex 358.798380 — REMEDY SYMPTOM diagram (page 13)
Fig. 13

Immediately prepare your unit for storage at the end of the season. STORAGE INSTRUCTIONS

  • Clean air vents and air inlet of debris.
  • Reassemble all loose parts, being sure that all handles are in place and are securely fastened. Replace any damaged parts.
  • If our blower isto be stored for a pedod of time, clean it thoroughly before storage. Remove any dirt, leaves, debris, etc, Store in a clean dry area.
  • Disconnect from the power source.
  • Clean the entire unit.
  • Store your unit in a well ventilated area and covered, if possible, to prevent dust and dirt accumulation. Do not coverwith plastic. Plastic cannot breathe and will induce condensation and eventual rust or corrosion.
  • Open Inlet coverand clean any dirt, grass, ordebris that has collected. Inspect the blower and vacuum tubes. Close and replace screw.

m.lllllll i liH i ,,,,,,,,,,,,,,,,,,,,,,,, Hill. ,,,,, .ll illl i i.H. i ,,.,,, ,,,,,,,,,,,,,,,,,,,,,,, , ,, TROUBLESHOOTING POINTS

I ii iiiiiiiiiiii i I i iiiiiiiiiii ii IL== ,H ,=, ,,, TROUBLESHOOTING CHART

REMEDY SYMPTOM

CAUSE

,,, i ,,,,,,,, , ,i J

Unit fails to operate.

A. Switch in the OFF position.

A. Push switch to the ON position.

B. Disconnected from power source. C. Circuit breaker tripped, or fuse

B. Reconnect unit to power source. C. Reset circuit breaker, or replace fuse.

blown. D. Mechanical failure.

D. Contact your Sears Service/Dept.

Unit vibrates abnormally.

A. Mechanical failure.

A. Contact your Sears Service/Dept.

u

A. Debris in air intake area. B. Mechanical failure.

Impeller will not tum freely.

A. Clean unit. Remove any debds. B. Contact your Sears Service/Dept.

ff situations occur which are not covered in this manual, use care and good judgement.

ff you need assistance, contact your Sears Service Center!Department or the CUSTOMER ASSISTANCE HOTLINE at 1-800-235-5878

, ,,,,,,,,,, · - ]3 -

Page 14 of the Univex 358.798380 user manual — (1-800-366-7278)
Page 14 · click to enlarge
Page 14
Univex 358.798380 — CRRFTSMRN o diagram (page 14)
Fig. 14 · CRRFTSMRN o

CRRFTSMRN o

12 AMP MOTOR 165 MPH Air Velocity E BLOWER/VAC

Operator's Manual

Model No.

358.798380

Each Electric BlowerNac has its own model number. The model number for your unit will be found on a decal attached to the unit. All parts listed herein may be ordered through Sears, Roebuck and Co. Service Centers and most Retail Stores.

IF YOU NEED REPAIR SERVICE OR PARTS:

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION

  • PRODUCT-"ELECTRIC BLOWER/VAC"

REPAIR SERVICE 1-800-4-REPAIR (1-800-473-7247)

  • MODEL NUMBER - 358.798380
  • PART NUMBER
  • PART DESCRIPTION

ORDERING PARTS 1-800-FON-PART

Your Sears merchandise has added value when you consider that Sears has service units nationwide staffed with Sears trained techni- cians.., professional technicians specifically trained on Sears prod- ucts, having the parts, tools and the equipment to insure that we meet our pledge to you, we service what we sell.

(1-800-366-7278)

i HOURs (csn i ! Mon.-Sat. 7a.m.-7 p.m. ! I Sun. 10 a.m. - 7 p.m. j

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Ask about the Univex 358.798380

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Univex 358.798380

Be the first to ask — other owners or our team will answer.

Original document

Univex 358.798380 manual PDF

14 pages·1.6 MB·Blower·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…