Instruction/ maintenance manual of the product EXS9110 Uniden
Go to page of 23
CO N T E N T S OF YOUR OWNER’S MANUAL CONTENTS Introduction ............................................................1 • Welcome ............................................................1 • Features ........................................
Introduction WELCOME Congratulations on your purchase of the Uniden EXS9110 cordless telephone. This phone is designed for reliability, long life, and outstanding performance utilizing the latest in 900 MHz Spread Spectrum technology.
INCLUDED IN Y OUR P A CKA GE • This Owners Manual • Precautions and Im portant Safety Instructions • Registration Car d 2 W all Mounting Screws Handset Base A C Adapter Recharg eable Batter y.
Installing and Adjusting Your Phone DESK/TABLETOP INSTALLATION 1) Plug the AC adapter cord into the 9 VDC input jack on the back of the base. 2) Wrap the AC adapter cord around the strain relief notch. 3) Plug the AC adapter into a standard 120 VAC wall outlet.
7) Attach the desktop stand to the base. 8) Set the base on a desk or tabletop and place the handset into the base as shown. Then, raise the antenna to a vertical position. WALL INSTALLATION ▼ Standard wall plate mounting This phone can be mounted on any standard AT&T or GTE wall plate.
4 ) Put the AC adapter cord inside the molded wiring channel, then wrap it around the strain relief notch. Plug the AC adapter into a standard 120 VAC wall outlet. 5) Plug one end of the short telephone cord into the TEL LINE jack on the back of the base, then plug the other end into a standard telephone jack.
8) Flip the retainer from front to back, then slide it into the slot so that the lip of the retainer faces up and the oval is at the bottom of the retainer. This will hold the handset in place. ▼ Direct wall mounting If you don't have a standard wall plate, you can mount your phone directly to the wall.
2) Remove the wall mount adapter from the notches at the top of the base. 3) Rotate the wall mount adapter 180 degrees and snap it into place at the bottom of the base. 4) Plug the AC adapter into the base. 5 ) Put the AC adapter cord inside the molded wiring channel, then wrap it around the strain relief notch.
6) Plug one end of the long telephone cord into the TEL LINE jack on the back of the base, then plug the other end into a standard telephone jack. 7) Line up the mounting slots on the base with the mounting screws on the wall, then push in and down until the phone is firmly seated.
INSTALLING THE HANDSET BATTERY PACK 1) Press in on the battery cover release and slide the cover down until it comes off. 2) Install the nickel-cadmium battery with the label facing down. 3) Slide the battery cover on until it snaps into place. 9 INSTALLING AND ADJUSTING ! Use only Uniden battery model (BT-990) supplied with your phone.
CHARGING THE BATTERY PACK ▼ Initial battery charging Before plugging the phone line into your new phone for the first time, fully charge the rechargeable battery pack for 15-20 hours without interruption. 1) Place the handset on the base. 2) Make sure that status LED lights.
▼ Low battery indicator The low battery indicator shows when the battery needs to be re-charged If the phone is not in use, the talk/batt low LED flashes every three seconds. If the phone is in use, the talk/batt low LED flashes every three seconds and the handset beeps.
SETTING THE PULSE/TONE SWITCH Be sure the PULSE/TONE switch is in the TONE position unless your local phone system uses pulse dialing. ADJUSTING THE RINGER CONTROLS ▼ Handset ringer volume When the phone is either charging or in standby mode, pressing the vol ▲ or ▼ key on the handset selects the handset ringer volume.
INSTALLING THE BELTCLIP ▼ To attach the beltclip 1) Remove the slot cover. 2) Put the beltclip in the slot and press down until it clicks. ▼ To remove the beltclip 1) Pull back on the release tab and pull the beltclip up. 2) Replace the slot cover.
HEADSET INSTALLATION Your phone may be used with an optional headset, the Uniden HS 910. To use this feature, simply insert the headset plug into the headset jack.
Using Your New Phone MAKING AND RECEIVING CALLS Handset On Base Handset Off Base To answer a call Pick up the handset. Press any button. To make a call 1) Pick up the handset. 2) Press talk . 3) Listen for the dial tone. 4) Dial the number. 1) Press talk .
ADJUSTING VOLUME DURING A CALL Press the vol ▲ or ▼ key on the handset to increase or decrease volume while on a call. Volume will return to preset level when you hang up. STORING A PHONE NUMBER IN MEMORY 1) Remove the handset from the base. 2) Press mem and the talk/batt low LED blinks.
CHAIN DIALING On certain occasions after dialing a number, you may be requested to enter an access code, such as your account number. You can enter this number into a memory location for later use by doing the following. 1) Store the access code into one of the memory locations (01-20) or press memory key a , b , c or d following steps 1-5 above.
REDIAL The redial key redials the last number dialed. The redialed number can be up to 32 digits long. TONE If you are dialing in the pulse mode and need to enter tone digits, press tone to enter the digits. Once the call has ended, the tone mode is canceled and pulse dialing resumes.
Troubleshooting QUICK REFERENCE CHART If your phone is not performing to your expectations, please try these simple steps before calling Uniden customer service. PROBLEM SUGGESTION The charge light won’t come on when the handset is placed in the base.
PROBLEM SUGGESTION The handset doesn’t ring or receive a page. • The Nickel-Cadmium battery pack may be weak. Charge the battery on the base unit for 15-20 hours. • The handset may be too far away from the base unit. • Place the base unit away from appliances or metal objects.
Specifications GENERAL The EXS9110 complies with FCC Parts 15 and 68. Frequency control: PLL Modulation: Direct Sequence Spread Spectrum; DBPSK Operating temperature: 0º to 50º C (+32º F to +122º F) BASE Frequency: 904.2 to 925.8 MHz (20 channels) Power requirements: 9V 350 mA (from AC adapter) Size: 5-1/2in.
AND FUNCTIONS CONTR OLS.
An important point after buying a device Uniden EXS9110 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Uniden EXS9110 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Uniden EXS9110 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Uniden EXS9110 you will learn all the available features of the product, as well as information on its operation. The information that you get Uniden EXS9110 will certainly help you make a decision on the purchase.
If you already are a holder of Uniden EXS9110, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Uniden EXS9110.
However, one of the most important roles played by the user manual is to help in solving problems with Uniden EXS9110. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Uniden EXS9110 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
