Instruction/ maintenance manual of the product DynaGST/1602G UNICOM Electric
Go to page of 17
16 Port 10/100/1000Base-T Gigabit Ethernet Switch with two SFP (mini) GBIC Slots DynaGST/1602G U SER’S M ANU AL PN: GEP-33216T.
Content 1. Introduction .............................................................. 1 Features ..................................................................... 2 Package Contents ...................................................... 3 2. Hardware Description .
.
1 1. Introduction Gigabit Ethernet over copper technology is a proven cost-effective way for network equipment to be upgraded from Fast Ethernet to Gigabit speeds. The need of expensive fiber optic cabling for Gigabit speeds is eliminated by using standard 4-pair Category 5e copper cabling.
2 Features Compatible with IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, IEEE802.3z Gigabit fiber and IEEE802.3ab 1000Base-T 16 Port Gigabit switch with two Mini SFP GBIC ports Automatic MDIX for all ports 4K entry MAC address table 2Mbit Memory buffer IEEE802.
3 Package Contents DynaGST/1602G Gigabit Ethernet switch Power Cord Four Rubber Feet User Manual DynaGST/1602G Gigabit Ethernet switch Power Cord User Guide Rubber Feet Figure 1-1. Package Contents Compare the contents of your DynaGST/1602G Gigabit Ethernet switch package with the standard checklist above.
4 2. Hardware Description This Section describes the hardware of the DynaGST/1602G Gigabit Ethernet switch. The physical dimensions of the DynaGST/1602G Gigabit Ethernet switch is: 440 x 224 x 44 mm (.
5 [Note] When the Mini GBIC module is installed, the Mini GBIC (Gigabit fiber) ports ha ve higher priority than the Gigabit copper ports and supercede them. It doesn’t matter if the Gigabit copper port is connected before or after the Mini GBIC port is connected.
6 Figure 2-3. LED Indicators LED Status Description Green Power On Power Off Power is not connected Green Port is operating at 1000Mbps. 1000 Off No device attached or in 10/100Mbps mode Green Port is connecting with the device. Blinking Port is receiving or transmitting data.
7 Mini GBIC LED The two Mini GBIC ports have two LED indicators each – LNK and ACT. The following table provides descriptions of LED status. Figure 2-4. Mini GBIC Port LED Indicators LED Status Description Green Port is connecting with device. LNK Off No device attached.
8 3. Installation Set the Switch on a sufficiently large flat space with a power outlet nearby. The surface should be clean, smooth, level, and sturdy. Ensure there is enough clearance around the Switch to allow air circulation and the attachment of the power cord and cables.
9 4. Network Application This section provides you a sample of network topology in which the DynaGST/1602G is used. In general, the DynaGST/1602G Gigabit Ethernet switch is designed as a high-bandwidth backbone switch.
10 5. Troubleshooting The Switch can be easily monitored through panel indicators to assist in identifying problems. This section describes common problems you may encounter and where you can find possible solutions. Diagnosing LED Indicator If the Link indicator does not light up after connection, check whether the network interface (e.
11 Cabling RJ-45 ports: Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100m. of Category 3,4 or 5 cable for 10Mbps connections, 100m. of Category 5e cable for 100Mbps connections, or 100m. of 4-pair Category 5e copper cabling for 1000Mbps connection.
12 6. Technical Specification The following table provides the technical specification of the DynaGST/1602G Gigabit Ethernet switch. Standard IEEE802.3 10Base-T IEEE802.
13 LED System: Power Per RJ-45 port: 1000Mbps, Link/Activity, Full duplex/ collision Mini GBIC port: Link and Activity Power Supply Internal power supply, AC 100~240VAC, 50/60 Hz Power Consumption 60W.
908 Canada Court City of Industry , C A 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 F ax: 626.964.7880 www .unicomlink.com e-mail: info@unicomlink.
An important point after buying a device UNICOM Electric DynaGST/1602G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought UNICOM Electric DynaGST/1602G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data UNICOM Electric DynaGST/1602G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, UNICOM Electric DynaGST/1602G you will learn all the available features of the product, as well as information on its operation. The information that you get UNICOM Electric DynaGST/1602G will certainly help you make a decision on the purchase.
If you already are a holder of UNICOM Electric DynaGST/1602G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime UNICOM Electric DynaGST/1602G.
However, one of the most important roles played by the user manual is to help in solving problems with UNICOM Electric DynaGST/1602G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device UNICOM Electric DynaGST/1602G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
