Instruction/ maintenance manual of the product 2500 Ultra Start
Go to page of 16
WWW .UL TRAST ARTERS.COM 2500 2500 2500M INST ALLA TION GUIDE Advanced R emote V ehic le Star ter & Alar m TECH SUPPORT Western Canada 1 800 279-0636 United States: 1 866 698-5872 Eastern Canada. Bilingual Support: 1 800 268-0683 E-Mail T ech Support: support@ultrastarters.
Installation Guide 2500 Wiring Diagram Page 3 Page 5 Page 6-7 Pre-Installation Page 4 Components Recommended Pre-Installation Procedures Recommended Install procedures Wire Connectors 6 Pin Connector .
Installation Guide WIRING DIAGRAM 3 1 3 5 2 4 6 2 1 4 3 6 5 7 8 10 9 12 11 14 13 10 12 11 13 4 PIN BLUE 4 PIN RED 4 PIN WHITE 4 PIN WHITE 4 PIN WHITE SIDE VIEW SA TELLITE LINK PLUG STA RTER DISABLE.
Installation Guide Recommended Pre-Installation Procedures - Control module - Remote transmitter(s) - Antenna with built in Program Button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness - 4 pin square harness. - 4 pin keyless entry harness - 4 pin Aux.
Installation Guide WIRING CONNECTORS 5 WIRING CONNECTORS Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. Red 12 power 30amp input Constant 12volt power at ignition harness. Red 12 power 30amp input Constant 12volt power at ignition harness.
Installation Guide QUICK START INST ALL Yellow Starter Output Connect To The V ehicles Starter Wire. Green Heater Output Connect To The V ehicles Accessory Wire. Red 12 power Input Connect to Constant 12 Volt Power Source - High Current. Red 12 power Input Connect to Constant 12 Volt Power Source - High Current.
Installation Guide Program mode allows you to adjust the settings and options of your system. Menu 2 - Alarm Settings - Page 9 This program menu contains settings that adjust the way the system operates for the user. Your system has been intelligently designed by installers with years of experience.
Installation Guide PROGRAMMING 8 PROGRAM MODE - USER SETTINGS Enter User Program Mode - See Page 7 for details on entering program mode 1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse 2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock *3 0.
Installation Guide PROGRAMMING 9 PROGRAM MODE - ALARM SETTINGS Setting 1 - Car Finder / 5th Channel Setting 2 - Secure Valet Mode Setting 3 - Parking Light Output Setting 4 - Horn Honk Timing - Pink w.
Installation Guide Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps.. Release the Program Switch.
Installation Guide 1 Safety ON 1 Flash Must press the start button twice to remote start vehicle 2* Safety OFF 2 Flashes Press the start button once to remote start vehicle.
Installation Guide OPERATIONS Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter.
Installation Guide OTHER FEATURES ACTIVA TING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode.
Installation Guide 14 1. Press and hold the # button for two seconds. 2. The system will flash the park lights and chirp the siren five times. **This feature can help find your vehicle in a crowded parking lot. 2 sec. 1. Press and hold the UNLOCK button for three seconds.
Installation Guide Remote Start Remote Stop Idle Mode Timer / Optional Temp Start Delay Dome Light - Auto Detection Ignition Auto Locks 1. Press & release the button.
Installation Guide RELAY DIA GRAMS 16 Blue Green Lock Un lock V ehicle Lock/Unlock Switch T o Control Relay or Actuators 87 86 85 87a 30 87 86 85 87a 30 Lock Un lock Veh icle Lock/Unlock Switch To C o.
An important point after buying a device Ultra Start 2500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultra Start 2500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultra Start 2500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultra Start 2500 you will learn all the available features of the product, as well as information on its operation. The information that you get Ultra Start 2500 will certainly help you make a decision on the purchase.
If you already are a holder of Ultra Start 2500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultra Start 2500.
However, one of the most important roles played by the user manual is to help in solving problems with Ultra Start 2500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultra Start 2500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
