Instruction/ maintenance manual of the product MAGICARD Sprinter Ultra electronics
Go to page of 8
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 I MAGICARD PRINTER INSTRUCTIONS FOR REPLACEMENT OF PRINTHEAD AND PRINTHEAD ASSEMBLIES WARNIN G - The Magicard colour printer contai ns hazardous voltages. CAUTI ON - The following procedures involve contact with Electrostatic Sensitive Devices.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 II 1. (a) Removing the cover Magicard 300 and Sprinter models. (1) Set the printer On/Off switch to off(0) and isolate from the mains supply. Remove the card cassette and Dye-Film from the printer.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 III 1. (b) Removing the cover Magicard Turbo models. (1) Set the printer On/ Off switch to Off(O) and isolate from the mains supply. Rem ove the card cassette and the Dy e-Film from the printer.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 IV 2. Removing old printhead/assembly (1) Remove the dy e-film and dye-film carrier from the printer. (2) If a tye-wrap is fitted to the grey ribbon cable plug on the back of the printhead, cut this tye-wrap taking great care not to cut the ribbon cable itself.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 V 3. Fitting the new printhead to the heatsink assembly (Magicard Dealers Only) CAUTION - The following procedures inv.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 VI (3) Che ck that t h e springs at th e ba ck of the pr inthe ad asse mbly are neat ly compressed and are not bulging outwards or inwards. If t hey are bulging the assembly will ha ve to be removed and refitted again until they remain neatly compressed.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 VII (4) The printhead angle has been f actory set. In order to ensure that it is still correct, compare the test card with th e images on the back page of this docu ment.
3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 VIII 7. And finally..... If your new thermal printhead fails to produce a good test image after following the above steps t hen please contact your suppli er. Too Positive Dark patches stressing out from the rear edge of the green square (watermarking).
An important point after buying a device Ultra electronics MAGICARD Sprinter (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultra electronics MAGICARD Sprinter yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultra electronics MAGICARD Sprinter - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultra electronics MAGICARD Sprinter you will learn all the available features of the product, as well as information on its operation. The information that you get Ultra electronics MAGICARD Sprinter will certainly help you make a decision on the purchase.
If you already are a holder of Ultra electronics MAGICARD Sprinter, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultra electronics MAGICARD Sprinter.
However, one of the most important roles played by the user manual is to help in solving problems with Ultra electronics MAGICARD Sprinter. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultra electronics MAGICARD Sprinter along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
