Instruction/ maintenance manual of the product Sicura Laminator Ultra electronic
Go to page of 24
Ultra Electronics Card Systems Quick Start Guide MAGICARD Sicura Laminator Page 1 MAGICARD Sicura Lami nator Quick Start Guide Laminator Setup Iss. 09 Janu ary 03 3504-22-01 Stock No.
Quick Start Guide Ultra Electronics Card Systems Page 2 MAGICARD Sicura Laminator Setting up your Sicura Laminator t akes just two easy step s: 1. Unpack and install the laminator A Preparing a Locati.
Ultra Electronics Card Systems Quick Start Guide MAGICARD Sicura Laminator Page 3 Location Requirements for yo ur laminator/printer: Preparing a Location for the Sicura Laminator and Printer A • An adequate power supply. • Ambient temperature +10 to +30 deg C.
Quick Start Guide Ultra Electronics Card Systems Page 4 MAGICARD Sicura Laminator Removing the Laminator from the Box Carefully open the box and remove any accessories.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Laminator Page 5 Checking the Package Contents C The MagiCard Sicura Card Laminator Envelope containing this Quick-Start guide A Roll .
Quick Start Guide Ultra Electronics Card Systems Page 6 MAGICARD Sicura Laminator Check that the Mains Supply Voltage is correct for your country. (Different models are manufactured for each supply voltage.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Laminator Page 7 Install the Lamination Film D Lift the transparent cover and move the roller lever to the OPEN position. Gently install the roll of film between the rollers. The black alignment marks on the film should be innermost.
Quick Start Guide Ultra Electronics Card Systems Page 8 MAGICARD Sicura Laminator Gently turn both rolls, to ensure that there is no slack film. Close the transparent cover.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Laminator Page 9 Connect the Laminator to a Power Supply E Check that the Laminator operating voltage is correct for your supply voltage. (Units cannot be changed from one voltage to another.
Quick Start Guide Ultra Electronics Card Systems Page 10 MAGICARD Sicura Lam inator The temperature will achieve the set point level after a delay of 4 minutes, and the READY indicator will illuminate.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 11 NOTE: The optimum roller temperature is best determined by trial and error, using your own cards and laminating film. The following notes are for your guidance only. • Cards with large, unprinted white areas require a higher temperature for lamination.
Quick Start Guide Ultra Electronics Card Systems Page 12 MAGICARD Sicura Lam inator Insert a card into the slot, side to be laminated uppermost. Cards should be clean, dust-free and not already overcoated. Adjust the IN/OUT position of the laminate on the card by screwing the core in or out, if necessary.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 13 Adjust the roller te mperature for good laminate adhesion as required (up to 200 ° C max). The display normally shows the roller core temperature in ° C. Adjust the setpoint temperature with the ↑ and ↓ keys as desired.
Quick Start Guide Ultra Electronics Card Systems Page 14 MAGICARD Sicura Lam inator IMPORTANT NOT E FOR SETTING U P YOUR RIO/TANGO PRI NTER DRIVER TO WORK WITH THE SICURA LA MINATOR – Please select the appropriate option in yo ur printer driver for best results.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 15 Note: The Rio/Tango printer can print cards faster than the Sicura can laminate them.
Quick Start Guide Ultra Electronics Card Systems Page 16 MAGICARD Sicura Lam inator Notes: 1. If the Magi c ard ca rd pri n ter pri n ts a card befo re the lamin ato r is ready (ie not ful ly a rm ed .
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 17 I Operating the Hopper/Sicura in Stand Alone Mode Clip the Card Feed Ho pper to the end of the Sicura card laminator and remove the Card Deflection Plate. Load the hopper w ith cards to be laminated (100 cards maximum).
Quick Start Guide Ultra Electronics Card Systems Page 18 MAGICARD Sicura Lam inator The Card Feed Hopper has been factory set for use with 30 thou cards. Should it require adjustment, carry out the following procedure: Adjusting the Hopper J Remove the hopper from the lam i nato r, remove the interface cable.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 19 The Sicura card laminator has three indicators to tell you what is happening: READY (Green) - When lit, indicates that it is ready to laminate a card. When flashing, indicates that it is still warming up.
Quick Start Guide Ultra Electronics Card Systems Page 20 MAGICARD Sicura Lam inator Correction operation depends on clean rollers to tr ansport cards, an undamage d laminating roller, and a dust-free environment. It is recommended that the laminator be cleaned after every roll of lamination film (250 cards).
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 21 Check the Installation : • Repeat the installation steps in this guide. • Check that the laminator mains voltage is correct. • Check that the laminating film is the right way round and passes through the optical sensor.
Quick Start Guide Ultra Electronics Card Systems Page 22 MAGICARD Sicura Lam inator Notice The information contained in this document is subject to change with out notice.
Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 23 Limited Warr ant y Informat ion 1) Coverage: Ultra E lectronics Ltd Warrants that the MAGICARD Sicura ca rd laminat.
Quick Start Guide Ultra Electronics Card Systems Page 24 MAGICARD Sicura Lam inator EC Declaration of Conformity Manufacturer's Name: Ultra Electronics Li mited. Manufacturer's Address: Waverley House, Hampshire Road, Granby Estate, W e y m o u t h , Dorset DT4 9XD E n g l a n d .
An important point after buying a device Ultra electronic Sicura Laminator (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultra electronic Sicura Laminator yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultra electronic Sicura Laminator - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultra electronic Sicura Laminator you will learn all the available features of the product, as well as information on its operation. The information that you get Ultra electronic Sicura Laminator will certainly help you make a decision on the purchase.
If you already are a holder of Ultra electronic Sicura Laminator, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultra electronic Sicura Laminator.
However, one of the most important roles played by the user manual is to help in solving problems with Ultra electronic Sicura Laminator. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultra electronic Sicura Laminator along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
