Instruction/ maintenance manual of the product PF Series Ultimate Products
Go to page of 44
.
.
Boiler Ratings and Ca pacities 1 FIG. 1 - INDOOR BOILERS BURNE R T Y P E A F G - O I L C F 3 7 5 - O I L AF G W /A IR I NT A KE BO O T G2 T - GA S R I E LLO 40 S E R IE S - OI L X 11½ 14 18 13½ 16 7 / 8 Y 8½ 11 15 10½ 13 7 / 16 ** Capacity greater than that requiring testing under F.
.
3 FIG. 2 - WEATHERPROOF BOILERS * Capacity greater than that requiring testing under F.T.C. regulations. For firing rates above 2.00 GPH, consult factory concerning pumping requirements for pool heating Firing rates of 2.00 gph or less use a Beckett Model AFG oil burner.
.
.
.
.
F r esh Air for Combustion - Chimne y V ented Boiler s 8 WARNING Be sure to provide enough fresh air for combustion. Enough air ensures proper combustion and assures that no hazard will develop due to the lack of oxygen. Y ou must provide for enough fresh air to assure proper combustion.
.
.
.
.
.
.
Oil Bur ner and Contr ols Star t-Up and Adjustment INDOOR CHIMNEY VENTED BOILERS Instruction manual enclosed in burner carton must be followed in regard to start-up and adjustment 1. St andard Beckett AFG or CF375 Oil Burner A Beckett model AFG oil burner is normally supplied with boilers to be fired at 2.
.
With all high efficiency boilers, care must be taken to minimize condensation. Therefore, cold standby is not recommended and may be used only with a piping, bypass as shown on Figure 12. This requires a change in control wiring. Please contact factory prior to making that change.
.
.
.
.
.
.
.
.
ANTIFREEZE 1. Antifreeze added to boilers must be non-toxic, and must be of a type. specifically intended for use in closed hydronic heating systems. Under no circumstances should automotive antifreeze be used. 2. Use of antifreeze in any boiler may reduce capacity by 10% or more and increase fuel consumption.
.
.
.
.
.
.
.
.
7 + ,6,6$5 ( 3$,5 3$5 76/,67 1 2 7$ 3$& . ,1 * /,67 % 2 ,/ ( 53$57 6 35.
.
.
R epair Par t s 38 KE Y NO . P A RT NO . DE S C RI P T I O N 1 146- 1 9- 2 01 Bec kett A F G S tan dar d O il Bur ner ( 2 .00 gph or l es s ) 1 BN 0890 1 Bec kett C F 3 75 Standar d Oi l Bur n er ( 2.0 0 gp h or m or e ) 1 10500 06 R iel lo 40 F 5 Stand ar d Oi l Bur ner ( 0.
.
SUGGESTED NOZZLES AND SETTINGS FOR BECKETT AFG AND CF375 OIL BURNER SERIES 40 NOTE: These settings are intended for initial start up only . Final adjustment must be made using combination test instruments Pump pressure is set at 140 psig. All burners fired at +.
.
14683825 Rev. 2, May 2003.
An important point after buying a device Ultimate Products PF Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultimate Products PF Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultimate Products PF Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultimate Products PF Series you will learn all the available features of the product, as well as information on its operation. The information that you get Ultimate Products PF Series will certainly help you make a decision on the purchase.
If you already are a holder of Ultimate Products PF Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultimate Products PF Series.
However, one of the most important roles played by the user manual is to help in solving problems with Ultimate Products PF Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultimate Products PF Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
