Instruction/ maintenance manual of the product MSR-72G-3 Turbo Air
Go to page of 16
T urbo air Speeds Up the P ace of Inno vation Refrigerator Freezer Installation and Operation Manual Please read this manual completely before attempting to install or operate this equipment! <Soli.
1. SPECIFICATION .......................................................................................... 2 2. SERIAL NUMBER ........................................................................................ 2 3. INSTALLATION .................
3 Turbo air 1. GOOD AIR CIRCULA TION - Be sure to avoid any partition and object which may stop the air flow. - Be sure that air space is allowed to flow the rear of the unit. Turbo air recommends that the rear of the unit would be no less than 5 inches from the wall.
4 Turbo air CLEANING 1. CLEANING ST AINLESS STEEL INTERIOR AND EXTERIOR (select models) : Damage to stainless steel finish due to improper use of cleaning products or non- recommended products is NOT covered under this product's warranty.
5 Turbo air B ASIC OPERA TION MSR-23NM MSR-23G-1 MSR-49NM MSR-49G-2 MSR-72G-3 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run.
6 Turbo air DISPLA Y P ANEL OF REFRIGERA T OR 9 TEMPERA TURE Q .C. 8 7 6 5 4 3 2 1 FA N DOOR QUICK COOLING TEMPERA TURE ˚F TEMP . SETTING QUICK COOLING F AN RUNNING DOOR OPENING QUICK COOLING BUTTON TEMP . CONTROL BUTTON (SEE T O P AGE 7) INNER TEMP .
7 Turbo air 1. If you push the Q.C. (QUICK Cooling) button, the compressor will run continuously until D-Senser detect 14 ˚ F (-10 ˚ C) to bring down the temperature more quickly. (max.comp.run time = 120 min.) 2. If you push the Q.C. button again during QUICK Cooling mode, the compressor will return to the normal operation.
8 Turbo air 1. It displays the inside temperature. 2. Display range is 14 ˚ F to 69 ˚ F (-10 ˚ C ~ +20 ˚ C). 3. When the inside temperature is lower than 14 ˚ F, the panel will display ‘ ’. and, higher than 69 ˚ F, the panel will display ‘ ’.
9 Turbo air B ASIC OPERA TION 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run. 2. The default temperature setting is No.
10 Turbo air DISPLA Y P ANEL OF FREEZER 9 TEMPERA TURE D.F . 8 7 6 5 4 3 2 1 FA N DOOR MANU AL DEFROST TEMPERA TURE ˚F TEMP . SETTING MANUAL DEFROST F AN RUNNING DOOR OPENING MANUAL DEFROST BUTTON TEMP . CONTROL BUTTON (SEE T O P AGE 1 1) INNER TEMP .
11 Turbo air 1. If you push MANUAL DEFROST button for 5 seconds, the Defrost will start. 2. During the Manual Defrost mode, the Up/Down button for the temperature control can not make the compressor cycle ON or OFF. 3. If you want to change the Manual Defrost mode to the normal mode, push MANUAL DEFROST button for 5 seconds.
12 Turbo air 1. It displays inside temperature. 2. Display range is -50 ˚ F to 50 ˚ F (-45 ˚ C ~ +10 ˚ C). 3. When inside temperature is lower than -50 ˚ F, the panel will display ‘ ’. and, higher than +50 ˚ F, the panel will show ‘ ’. 1.
13 Turbo air BEFORE REQUESTING SER VICE SYMPT OMS CA USES SOLUTIONS Freezer is melting f ood. The unit does not refrigerate at all. The unit does not refrigerate well. There is a loud noise. There are dew-dr ops on the unit exterior . There are dew-dr ops on the unit interior .
14 Turbo air MANUF A CTURING COMP ANY Turbo air warrants to the original purchaser of every new-Turbo air refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or w.
15 Turbo air WHA T IS NO T CO VERED BY THIS W ARRANTY Turbo air’s obligation under warranty is limited to either repair or replacement of parts, subject to the additional limitation s below. This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this warranty.
Warranty Claims... All claims for parts or labor must be made directly thorough Turbo Air. All claims should include: model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all pertinent information supporting the alleged defect.
An important point after buying a device Turbo Air MSR-72G-3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Turbo Air MSR-72G-3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Turbo Air MSR-72G-3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Turbo Air MSR-72G-3 you will learn all the available features of the product, as well as information on its operation. The information that you get Turbo Air MSR-72G-3 will certainly help you make a decision on the purchase.
If you already are a holder of Turbo Air MSR-72G-3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Turbo Air MSR-72G-3.
However, one of the most important roles played by the user manual is to help in solving problems with Turbo Air MSR-72G-3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Turbo Air MSR-72G-3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
