Instruction/ maintenance manual of the product T-106 Troy-Bilt
Go to page of 17
Owner’s Manual • SET-UP • OPERATION • MAINTENANCE IMPORTANT Read Safety Rules and Instructions Carefully PRINTED IN CANADA OG-4003 Walk Behind Mower Model: T-106.
2 CALLING CUSTOMER SUPPORT • L OCA TE YOUR MODEL NUMBER AND SERIAL NUMBER which appears on your unit and record the information in the space provided below . IMPORTANT: You must have these numbers, along with the date and proof of purchase to receive warranty or service.
GENERAL OPERATION • Read, understand, and follow all instruc - tions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering re - placement parts.
tive and may result in personal injury through contact with the rotating blade. The blade control handle must operate easily in both directions and automatically return to the disengaged position when released. • Never operate the mower in wet grass.
self or your clothes which can ignite. Wash your skin and change clothes immediately . a) Use only an approved gasoline con - tainer . b) Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner . Always place containers on the ground away from your vehicle before filling.
6 15 º USE THIS SHEET AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. A CORNER OF A BUILDING FOLD ON DOTTED LINE, REPRESENTING A 15 º SLOPE OR A FENCE POST SIGHT AND HOL D THIS LEVE.
UNPACKING • Remove the lawn mower and all parts from the carton. Make certain all parts and litera- ture have been removed from the carton before the carton is discarded. CAUTION: Disconnect spark plug wire. if the wire is not equipped with a rubber boot, see separate engine manual for grounding procedure.
ATTACHING THE BLADE CONTROL CABLE • The brake cable is attached to the engine, and has a “Z” fitting on the loose end. Route the brake cable over the lower handle. Place end of cable through the hole in the control box as shown in figure 3. Push the plastic fitting until it locks into the hole in the throt - tle box.
TO CONVERT YOUR MOWER FROM A MULCHER TO A SIDE DISCHARGE MOWER • Lift mulching plug. Slide the two hooks on the side discharge deflector under the hinge pin on the mulching plug assembly .
FOR THE BEST RESULTS WHEN MULCHING: Clear lawn of debris. Be sure that the lawn is clear of stones, sticks, wire or other foreign objects which could damage the lawnmower.
• Remove the hairpin clips from the weld pins on the handle brackets. Press out on the legs of the lower handle. Remove lower han - dle from the mower . • T urn the lower handle around so the notch on the bottom of the lower handle is facing forward as shown in Figure 10.
CAUTION: Cutting grass in sandy soil condition causes abrasive wear to the blades. After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the original shape. Cutting effi - ciently will be reduced and the blade should be replaced.
13 Engine Shroud Chart NOTE: this chart shows all the optional engine shrouds for the lawn mowers covered in this manual. To order replacement parts, please refer to the shroud and hardware applicable to your lawn mower unit.
14 2 3 4 5 6 7 8 9 10 11 12 13 8 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 32 33 34 33 36 37 38 35 46 46 45 22 20 39 40 27 21 26 19 23 24 25 41 42 43 44 38 1 14 38 1 31.
REF P ART NO. NO . N° DE N° DE RÉF PIÈCE DESCRIPTION DESCRIPTION 1 647-0004 Control Handle Guidon de la commande 2 710-1270 Oval C-Sunk Scr 1/4-20 X 1.31" Lg. Vis à tête noyée 1/4-20 X 1,31 po de lg. 3 712-0324 Hex Ins. L -nut 1/4-20 Gr . 8 Nylon Écrou hex.
16 THREE (3) YEAR LIMITED WARRANTY For three (3) years from the date of original purchase of our products, we will either repair or replace, at its option, free of charge, F.O.B. Factory or authorized service firm, any part found to be DEFECTIVE IN MATERIAL and WORKMANSHIP for the original purchaser.
17 note s....
An important point after buying a device Troy-Bilt T-106 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Troy-Bilt T-106 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Troy-Bilt T-106 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Troy-Bilt T-106 you will learn all the available features of the product, as well as information on its operation. The information that you get Troy-Bilt T-106 will certainly help you make a decision on the purchase.
If you already are a holder of Troy-Bilt T-106, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Troy-Bilt T-106.
However, one of the most important roles played by the user manual is to help in solving problems with Troy-Bilt T-106. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Troy-Bilt T-106 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
