Instruction/ maintenance manual of the product 466 Troy-Bilt
Go to page of 20
Operator's Manual 21" Three-in-One Lawn Mower Model 466 IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal co.
TABLE OF CONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Slope Gauge ...................................................................................................... 6 Assembling Your Lawn Mower .
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if net fol]owed, could endanger the personal safety and/or property of yourself and others. Read and fel]ew all instructiens in this manual before attempting te eperate this machine.
serious personal injury. If you feel you are losing yeur feeting, release the blade control handle immediately and the blade will step rotating within three seconds. "16. Mew in daylight or geod artificial light. Walk, never run. Step the blade when crossing gravel drives, walkways er reads.
fs hot or running. Allow engfne to cool at least two minutes before refueling. "10. Never over fill fuel tank. Ff]l tank to no more than ½ fnch below bottom of ffller neck to provfde space for fuel expansion. "11. Replace gasolfne cap and tighten securely.
4 SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST I I ¢,D 15o WARN,NG Do not mow on inclines with a slope in excess of "I 5 degrees (a rise of approximately 2-'I12 feet every "I 0 feet).
SECTION 3: ASSEMBLING YOUR LAWN MOWER Removing UnitFrom Carton • Remove staples, break g]ue on top flaps or cut tape at carton end and peel along top flap to open Lower Han,,_"_ carton. • Remove loose parts if included with unit (i.e., operator's manual, hardware pack etc.
Insert post of cable ties that are on lower handle into the holes provided on the lower handle. The holes may be on the inside or outside. Pull cable ties tight and cut off the extra.
Figure 9 Removing Grass Catcher • Lift the rear discharge door on the mower. • Lift the grass catcher up, out of the slots in the handle bracket assemblies.
SECTION 4: KNOW YOUR LAWN MOWER Read this owner's manual and safety rules befere operating your lawn mower. Compare the illustrations tn Figure "1 1 with your lawn mewer te familiarize yourself with the location of various contrels and adiustments.
SECTION 5: OPERATING YOUR LAWN MOWER Gas and OilFill-Up WARNING: Never fill fuel tank indoors= or when engine is running or hot. Do not smoke ............. when filling up the fuel tank. • Service the engine with gasoline and oil as instructed in the separate engine manual packed with your mower.
SECTION 6: MAINTAINING YOUR LAWN MOWER WARNING: Always stop the engine and disconnect the spark plug wire before ............ performing any maintenance work or adjustments on your lawn mower. and surrounding areas while the mower engine fs hot because temperature of these areas of the engine may exceed "150 o F.
SECTION 7: SERVICING YOUR MOWER Blade Care Periedically inspect the blade adapter and pulley for cracks, especially if you strike a foreign object. Replace when necessary. _%== WARNING: When remeving the cutting _ blade for sharpening or replacement, protect w hands by using heavy gleves or a thick rag te grasp the cutting blade.
Loosen this screw Right Front Left Front Wheel Wheel 4 / Shoulder Screw Screw Transmission Front Drive Cover Figure 14 • Slide the belt off the engine pulley and around the blade. See Figure 15. ,_.= WARNING: As always, use a thick piece of _rag to handle the blade while sliding the belt _ around it.
, Handle Notch J AdjustTnent Lever Figure 17 Cutting Height IMPORTANT: All wheels must be placed in the same relative position. • For rough or uneven lawns, move the height adjustment lever tea higher pesition. This will help stop scalping of the grass.
SECTION 10: TROUBLE-SHOOTING GUIDE Problem Possible Ceuse Corrective Action Engine fails to start 1. Blade control hand]e disengaged "1. Engage blade control handle 2. Spark plug wire disconnected 2. Connect wire to spark plug 3. Fuel tank empty, or stale fuel 3.
Safety & Decorative Labels iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ¸_(Mo_ELi_TEiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii 777_0118 777D6002 ....... iiiiii_7_B060!0iiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii _NOI'E: _lqO r',.
SECTION 11: PARTS LIST FOR MODEL 466 11 4 17 24 25 49 7O IMPORTANT: For a proper working machine, use Factory Approved Parts, V-BELTS are specially designed to engage and disengage safely. A substitute (non OEM) V-Belt can be dangerous by not disengaging completely.
Model 466 Ret. Pert No. No. 1. 747-2136 2. 647-0004 3. 749-1501 4. 710-1270 5. 746-0883 6. 712-0324 7. 746-0551 8. 749-0928A 9. 746-1146 10. 710-0606 11. 710-1174 12. 720-0284 13. 736-0451 14. 720-0279 15. 710-1205 16. 764-0310 17. 764-0311 18. 631-0075B 23.
MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Efilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories.
An important point after buying a device Troy-Bilt 466 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Troy-Bilt 466 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Troy-Bilt 466 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Troy-Bilt 466 you will learn all the available features of the product, as well as information on its operation. The information that you get Troy-Bilt 466 will certainly help you make a decision on the purchase.
If you already are a holder of Troy-Bilt 466, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Troy-Bilt 466.
However, one of the most important roles played by the user manual is to help in solving problems with Troy-Bilt 466. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Troy-Bilt 466 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center