Instruction/ maintenance manual of the product 4510 Troy-Bilt
Go to page of 28
TRO Y -BIL T L LC, P .O . BOX 3 6 1 1 3 1 CLEVE LAND, OHIO 4 4 1 36 - 001 9 Print ed In USA O p e r a t O r ’ s M a n u a l Safe Ope ration Practices • Se t-Up • Operatio n • Maintenance • S.
T o Th e O wne r 1 2 Record Product Information Befo re set ting up and o peratin g your new equip ment, pl ease loc ate the mode l plate on the e quipment and re cord the informati on in the provi ded area to the r ight.
Im por tant Sa fe Opera ti on Pra c tic es 2 3 T raining Read, un ders tand, an d follow all ins truc tions on th e 1 . machine an d in the manual(s ) b efore at tempting to assembl e and ope rate. Keep this manual in a s afe place fo r future an d regular re ference and f or order ing replacem ent par ts .
4 s e c t i O n 2 — i M p O r t a n t s a f e O p e r a t i O n p r a c t i c e s Safe Handling of G asoline T o avoid pers onal injur y or prop er t y damage us e ex treme c are in handling gas oline. Gas oline is ex tre mely f lammab le and the vapo rs are ex plosive.
5 s e c t i O n 2 — i M p O r t a n t s a f e O p e r a t i O n p r a c t i c e s Maintena nce & Storag e Never tamp er with s afet y devices . Check the ir prope r 1 . oper ation regul arly . R efer to the mai ntenance and adjustm ent sec tions of this m anual.
6 s e c t i O n 2 — i M p O r t a n t s a f e O p e r a t i O n p r a c t i c e s Safet y S y mbols This pa ge depic t s and describ es saf et y symb ols that may app ear on this pro duct . Read, un ders tand, an d follow all ins truc tions on th e machine b efore at tempting to ass emble and o perate.
Secure th e uppe r handle and l ower handle with th e two 4. wing nut s and carr iage bo lts remove d earlier. Tighten the two w ing nuts alr eady inst alled in th e upper h oles to f irmly secure th e uppe r handle and sup por t tube s. See Figur e 3- 2.
Place chute assembl y onto chute base as shown in Figu re 3-5. Make sure that the chute notches e ngage wi th the spiral en d of chute direc tion al control, and the t wo f lang e keeper s are bene ath the f lange on th e chute base. Secure f lan ge keep er removed earli er with lo ck nuts and s crews.
Auger and Driv e Control Cables W AR NING ! Prior to op erating your snow thrower, caref ully read an d follow all inst ruc tions be low . Perf orm all adjus tments to ver if y your snow thrower is oper ating safe ly and pro perly.
W AR NING ! Do not over-tighten the cab le. Over- tightening may prevent the aug er from dis engaging and comprom ise the saf et y of the snow thrower. If adjus ting the auge r cable, threa d the lock nut d own to 4. length en the cab le as necess ar y to stop the au ger from turning w hen the control is re lease d.
Snow thrower controls and f eatures are descr ibed b elow and illustrate d in Fig. 4 - 1 . NOTE: For de taile d informatio n on all engin e controls, refe r to the sep arate Briggs & Strat ton Engine O perato r’s Manual.
Primer Bulb Pressing the pr imer bulb fo rces fuel dire ctl y into the engine ’ s carbur etor to aid in st ar ting a “Cold” e ngine. NOTE: D o not use the pr imer bulb to res tar t a warm e ngine af ter a shor t shutdown . Oil Fil l Engine oil leve l can be che cked and oil a dded thro ugh the oil f ill.
T w o - Wa y Chute Control ™ The t wo -way chute control is l ocated o n the lef t sid e of the dash pane l and is used to contro l the dista nce of snow discharge f rom the chute. T o change the up per chute angl e to control the dist ance • that snow is thrown, pi vot the lever for ward o r back ward.
Starting The Engine At ta ch spa rk pl ug wir e to sp ar k p lu g. Make ce r ta in the 1. me ta l l oo p o n t he en d o f t he sp ark pl ug wi re ( insi de th e ru bb er bo ot) is fa ste ne d se cur el y ov er the me t al tip on th e sp ar k p lu g. Make cer tain bo th the auger contro l and drive control are 2.
Operating Tips NOTE : Allow the engin e to warm up for a f ew minutes. Th e engine w ill not develop f ull power until it re aches op erating temperature. W AR NING ! The temp erature of th e muf f ler and the surroun ding areas may excee d 1 50° F .
With the mo unting ho les toward the back , slid e the new s have 4. plate into positio n and secur e with the fas tener s removed previousl y . Lubric ation Gear Shaft The g ear (hex) sha f t should be lu bricated at l east once a se ason or af ter ever y t went y-f ive (25) hours of op eratio n.
Figur e 6 -5 Auger S haf t At least once a seas on, one at a tim e, remove the shear p ins from the auge r shaf t. Spray lubri cant inside the hub o f each auger spiral asse mbly and aro und the spa cers on the au ger shaf t. Grease f it tings c an also be fou nd at each end of th e auger shaf t .
Loosen t he two nu ts which s ecure the chute b racket and 1 . repositi on it slightly. Refer to Figure 6 -5. Retighten th e nuts. 2. Drive Con trol Refe r to “ Au ger an d Dr ive Cont rol C ab les ” of the Asse mbly & Se t-Up - Sec tion 3 f or instru ctio ns to adjust the dri ve control.
Belt Replac ement Belt Remo val Preparation Disconnect the chute crank assembly at the discharge 1 . chute end by remo ving the hairpin clip and the f lat washer . Refer to Figure 7 - 1 . Remove the hex screws and lock nuts securing the 2 . for ward end of the suppor t tubes to the back of the auger housing, and pivot the tubes upward.
Slip the auger con trol b elt ( the f ront belt) off the engine 2. pulley . Pull the 3. brake bracket as se mbly towards t he c able guide roller and unhook the auger cable “Z” f it ting. Refer to Figure 7 -5 . F rom b oth sides of the frame assembly , use a 1 /2" 4.
If also replacing the drive belt, proceed to the “Drive 1 1 . Belt ” instruc tion. If not, reposition the transmission frame back onto the auger housing. Install the drive belt on the engine pulley , re -connec t the auger cable “Z” f itting and auger idler ro d ferrule to the brake bracket.
Slide the bearing onto the left e nd of the hex shaf t and 1 4. press int o the ho le on the lef t side the frame. Plac e the b elleville washer ( rounded side toward head) 1 5. onto the hex screw remov e d earlier , and insert the screw int o the threaded ho le of the hex shaf t.
Of f- S eason S torage If the snow throw er will not be use d for 30 days or longer , the equipment needs to be stored prop erly . Follow storage instructions be low to ens ure top per formance from the snow thro wer for many more years.
24 Problem Cause Remedy Engine fa ils to star t Choke control not in O N position . 1. Spark plu g wire disconne cte d. 2. Fuel tank empt y or s tale f uel. 3. Engine not p rimed . 4. F ault y sp ark plug. 5. Safet y key not ins er ted . 6. Move choke control to ON p osition.
R epla cem ent P art s 9 25 Component Description P ar t Num ber Ex tention Cord, 1 1 0V 929 - 0 0 71 Auger Drive Belt 9 5 4 - 0 413 1 Wheel D rive Belt 95 4 - 03 67 F ric tion Whe el Assembly 9 1 8 - 0 4 17 8 F ric tion Whe el w/Bonded Rubber 718 - 0 4 0 3 4 Halogen L amp, 1 2V , (#8 9 0) 7 2 5 -16 5 8 Shear Pin, 1 .
No te s 10 26.
27 s e c t i O n 1 0 — n O t e s.
MANUF A CTURER’S LIMITED W ARRANTY FOR GDO C - 100 0 20 R E V . A Th e limi te d wa rr an t y s e t for th bel ow is g iv en by T r oy- Bil t LLC w i th re spe c t to ne w mer ch an dis e purc ha se.
An important point after buying a device Troy-Bilt 4510 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Troy-Bilt 4510 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Troy-Bilt 4510 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Troy-Bilt 4510 you will learn all the available features of the product, as well as information on its operation. The information that you get Troy-Bilt 4510 will certainly help you make a decision on the purchase.
If you already are a holder of Troy-Bilt 4510, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Troy-Bilt 4510.
However, one of the most important roles played by the user manual is to help in solving problems with Troy-Bilt 4510. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Troy-Bilt 4510 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
