Instruction/ maintenance manual of the product SCSCF30XX-10X Transition Networks
Go to page of 7
* Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. Part Number Port One - Copper Port Two - Duplex Fiber-Optic SCSCF3011-100 75 ohm coax (BNC) ST, 1300 nm multimode 2 km (1.2 miles)* SCSCF3013-100 75 ohm coax (BNC) SC, 1300 nm multimode 2 km ( 1.
2 SCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Part Number Port One - Copper Port Two - Single Fiber Optic SCSCF3029-102 and -103 are intended to be installed in the same network where one is the local converter and the other is the remote converter.
4 SCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the jumper. Failure to observe this caution could result in damage to, and subsequent failure of, the Device.
SCSCF30xx-10x 6 Operation After installation, the Device should function without operator intervention. Use the status LEDs to monitor the Device operation in the network. SDC Green on The coax link is up. Green flashing The coax link is in loop-back mode.
8 SCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Cable Specif ications -- Continued SCSCF3029-102 1310 nm (TX) / 1550 nm (RX) simplex SCSCF3029-103 1550 nm (TX) / 1310 nm (RX) simplex Fiber-optic Transmitter Power: min: -8.
10 SCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 6. Is Data Transfer Failing? YES • Verify the local copper connection by starting a local copper loop-back (set the loop-back switch on the local Device to “CL”) and then use a bit error test unit at the local location to run a bit error test.
Trademark Notice All trademarks and registered trademarks are the property of their respective owners. Copyright Restrictions © 2001, 2004 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means - graphic, electronic, or mechanical - without written permission from Transition Networks.
An important point after buying a device Transition Networks SCSCF30XX-10X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transition Networks SCSCF30XX-10X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transition Networks SCSCF30XX-10X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transition Networks SCSCF30XX-10X you will learn all the available features of the product, as well as information on its operation. The information that you get Transition Networks SCSCF30XX-10X will certainly help you make a decision on the purchase.
If you already are a holder of Transition Networks SCSCF30XX-10X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transition Networks SCSCF30XX-10X.
However, one of the most important roles played by the user manual is to help in solving problems with Transition Networks SCSCF30XX-10X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transition Networks SCSCF30XX-10X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
