Instruction/ maintenance manual of the product P332MF Transition Networks
Go to page of 34
Quick Start for Hardware Installation A vaya P332MF S t ackable Switch 10-300712 Issue 1 September 2005.
Copyright 2005, A vaya Inc. All Right s Reserved Notice Every ef f ort was made to ensure that the informati on in this document was complete and accurate at the time of print ing. However , information is subject to change. Wa r r a n t y Avaya Inc. provides a li mite d warranty on this product.
Issue 1 September 2005 3 Chapter 1: Before you S t art . . . . . . . . . . . . . . . . . . . . . . . . . 5 Gathering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Defining the Installation . . . . . . . . . . . . . . .
Contents 4 Quick Start for Hardware Installa tion: P332MF Stackable Switch Installing from the P330 Documenta tion and Utilities CD . . . . . . . . . . . . 32 Install from the Avaya Web Site . . . . . . . . . . . . . . . . . . . . . . . . . 33 Install from your Local Web Site .
Issue 1 September 2005 5 Chapter 1: Before you S t art Before you insta ll your Avaya Switch, prep are all the information, re sources, and tools that you need during the insta llation process. Good prep aration ensures a smooth inst allation with the least amount of interruption.
Before you Sta rt 6 Quick Start for Hardware Installa tion: P332MF Stackable Switch Prep aring Inst allation Files Ensure that you load the latest versions of the firmware file fo r the P330. Y ou can download the firmware file needed for your inst allation from the A vaya Support W eb site, at http:// support.
Choosing the Installation Site Issue 1 September 2005 7 ● The environmental condition s match the requirements listed in Ta b l e 2 . ● The power source matches t he specifications shown in T able 3 : See the Avaya P333T User ’s Guide, 03-30 0148, for additional information on environment al requirements.
Before you Sta rt 8 Quick Start for Hardware Installa tion: P332MF Stackable Switch Building a st ack Follow the guidelines in this section in order to build a working stack using any combination of the following devices: ● P330 series ● P330-ML series ● G700 ● P330 series 1.
Building a stack Issue 1 September 2005 9 Note: Note: Position the C360 switches either at the top or botto m of the stack to ensure mechanical stability . T able 4: Firmware V ersions Matrix Required version St ack with out C360 St ack with C36 0 Switch 3.
Before you Sta rt 10 Quick Start for Hardware Insta llation: P332MF Stackable Switch S t ack Master election rules T able 5 lists the switches in order of elec tion priority from highest to lowest.
Stack Master election rules Issue 1 September 2005 11 Figure 1: Example st ack elections Figure notes: 1. S t ack Master C364T-PWR Layer 3 C363T-PWR Layer 2 P334T-ML Layer 3 P333T G700 P363T-PWR Layer.
Before you Sta rt 12 Quick Start for Hardware Insta llation: P332MF Stackable Switch.
Issue 1 September 2005 13 Chapter 2: Unp ack the Device ELECTROST A TIC ALERT : ! ELECTROSTATIC ALERT : Wear an anti-st atic wrist ground strap whenever yo u handle components o f a P330. Connect the strap to an approved gro und, such as an unpain ted metal surface.
Unpack the Dev ice 14 Quick Start for Hardware Insta llation: P332MF Stackable Switch Document ation ● Avaya P332MF Quick S t art Guide (this document) ● Avaya P330 Release Notes One RJ45 to DB9F .
Documentation Issue 1 September 2005 15 ● Avaya P330 Documentation and Utilities CD (se e detail below) ● Avaya Communication W arranty and License Agreement A vaya P330 Documentation and Utilities CD The CD contain s the latest User's Guides for the A vaya P330 sta ckable switches and files for use with the Embedded W eb Manager .
Unpack the Dev ice 16 Quick Start for Hardware Insta llation: P332MF Stackable Switch.
Issue 1 September 2005 # Chapter 3: Mount the Device Y ou can mount the P330 in a rack. The P330 chassis fits in most standard 19-inch racks. It is 2U (3. 5”, 88 mm) high. Before you Inst all the P330 in a Rack ● Disconnect all cables from th e unit before proceeding with the rack installatio n.
Running H/F 1 # Quick Start for Hardware Installa tion: P332MF Stackable Switch Figure 3: Open hinged end Figure notes: 1. Open hinged end 2. Position the unit in the rack. 3. Secure the unit to the rack, taking care not to overtighten the screws. 4. Snap closed the hinged ends of the front panel.
Issue 1 September 2005 19 Chapter 4: Power Up Connecting the P330 to the main electrical supply provide s power to the switch. VOL T AGE ALERT : ! VOLTAGE ALERT : T o isolate the switch completely , you must disconnect all power connections: AC plug or DC terminal block and DC BUPS power .
Power Up 20 Quick Start for Hardware Insta llation: P332MF Stackable Switch P330 DC version VOL T AGE ALERT : ! VOLTAGE ALERT : Before pe rforming any of the following pr ocedures, ensure that DC power is OFF .
P330 DC version Issue 1 September 2005 21 3. negative to negative ! W ARNING: ! WARNING: Always connect the ground wire first a nd disconnect it last..
Power Up 22 Quick Start for Hardware Insta llation: P332MF Stackable Switch.
Issue 1 September 2005 23 Chapter 5: Prep are for Configuration This chapter provides information on prep aring the P330 for configurati on, a nd discusses the following topics: ● Establishing a Con.
Prepare for Configuration 24 Quick Start for Hardware Insta llation: P332MF Stackable Switch 1. Use the serial cable sup plied to att ach the RJ -45 console connector to the Console po rt of the active P330 switch. Co nnect the DB-9 connec tor to the serial (COM) port on your PC/ terminal.
Establishing a Telnet Conne ct ion Issue 1 September 2005 25 4. At the prompt, type: set interface inband <vlan> <ip_ad dress> <netmask> Replace <vlan> , <ip_address> and <netm ask> with the VLAN, IP address, and net mask of the st ack.
Prepare for Configuration 26 Quick Start for Hardware Insta llation: P332MF Stackable Switch Configuring the Switch This section describes the procedures for the first-time configuration of the A vaya P330. The factory defaults are set out in detail in th e tables included in this ch apter .
Configuring the Switch Issue 1 September 2005 27 5. Press Enter to save the destina tion and gateway IP addresses. A vaya P330 Default Settings If you wish to change the default p arameters shown and configure the mandatory p arameters, we recommend that you use the Command Line Interface (CLI).
Prepare for Configuration 28 Quick Start for Hardware Insta llation: P332MF Stackable Switch Tip : Tip: Functions operate in their default settings unless configured otherwise.
Issue 1 September 2005 29 Chapter 6: Device Manager This chapter describes the inst allation procedur es for the Device Manage r of the Avaya P330. Overview The Device Manager provides the following: ● Managing and monitoring Power over Ethernet. ● Device Configuratio n - Viewing and modify ing the different device configurations.
Device Ma nager 30 Quick Start for Hardware Insta llation: P332MF Stackable Switch Configuring the Device Manager Y ou can configure several Device Manager pa rameters using the CLI.
Running th e De vi ce Ma na g er Issue 1 September 2005 31 - The user name is “root”. - The default p assword for read-only access is “root”. - The default p asswords for re ad-write access is “root”. Note: Note: The P330 Device Manager p asswords are the same as those of the CLI.
Device Ma nager 32 Quick Start for Hardware Insta llation: P332MF Stackable Switch Figure 8: Device Manager 3. If you do not have th e Java plug-in installed, follow the instructions on the Welcome p age for a variety of options to inst all the plug-in (see Installin g the Java Plug-in ).
Installing the On-Line Help and Java Plug-In on your Web Site Issue 1 September 2005 33 4. Browse to the embweb-aux -files folder on the CD. 5. Double-click plugin_a_b_c.exe (a, b a nd c are the version numbers of the plug-in). 6. Follow the on-screen instructions.
Device Ma nager 34 Quick Start for Hardware Insta llation: P332MF Stackable Switch Document ation The Device Manager comes with a det ailed User ’s Guide includ ing a Glossary of T erms and an overview of Data Communications concept s.
An important point after buying a device Transition Networks P332MF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transition Networks P332MF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transition Networks P332MF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transition Networks P332MF you will learn all the available features of the product, as well as information on its operation. The information that you get Transition Networks P332MF will certainly help you make a decision on the purchase.
If you already are a holder of Transition Networks P332MF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transition Networks P332MF.
However, one of the most important roles played by the user manual is to help in solving problems with Transition Networks P332MF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transition Networks P332MF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
