Instruction/ maintenance manual of the product E-FX-HB-0800 Transition Networks
Go to page of 8
Minneapolis, MN 55344 USA 100BASE-FX Fast Ethernet ™ Unmanaged Fiber Hub with TX or FX Uplink E-FX-HB-1600, E-FX-HB-0800 USER’S GUIDE The stackable, rack-mountable E-FX-HB-1600 and E-FX-HB-0800 se.
E-FX-HB-xx00 IN THE NETWORK Install one E-FX-HB-xx00 hub and use fiber cable to set up a workgroup by connecting the hub to terminal devices. Install an optional backbone uplink adaptor at the back of the hub and use copper or fiber cable to connect the workgroup to a network backbone.
CABLE SPECIFICA TIONS T wisted Pair Cable and Connector Specifications MA-TX Category 5 twisted-pair copper Either shielded twisted-pair (STP) or unshielded twisted-pair (UTP) can be used.
INST ALLA TION Optionally Install Expansion Adapter WARNING: Remove AC line cord from power source before installing expansion adaptor in E-FX-HB-xx00.
F AULT ISOLA TION and CORRECTION If the E-FX-HB-xx00 fails, isolate and correct the fault by determining the answers to the following questions and then taking the indicated action: 1.
Install E-FX-HB-xx00 at Site WARNING: During the site installation, handle the E-FX-HB-xx00 in such a way that the E-FX-HB-xx00 does not fall. Failure to observe this warning could result in injury to personnel and/or equipment damage. NOTE: If E-FX-HB-xx00 is shipped with brackets installed, proceed to step 2.
Power the E-FX-HB-xx00 NOTE: When the hub is connected to an AC outlet supplying 100-240VAC at 50-60 Hz, the hub automatically powers ON To power ON the E-FX-HB-xx00: 1. Locate power receptacle at back of E-FX-HB-xx00. 2. Plug unit end (female) of power cord into E-FX-HB-xx00 power receptacle.
Optionally Connect to Backplane through TX Uplink NOTE: Refer to 512-bit rule (page 3) to keep cable lengths within acceptable bounds. To connect twisted-pair cable from E-FX-HB-xx00 100BASE-TX uplink adapter to network: 1. Locate 100BASE-TX uplink adapter installed at E-FX-HB-xx00 back.
An important point after buying a device Transition Networks E-FX-HB-0800 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transition Networks E-FX-HB-0800 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transition Networks E-FX-HB-0800 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transition Networks E-FX-HB-0800 you will learn all the available features of the product, as well as information on its operation. The information that you get Transition Networks E-FX-HB-0800 will certainly help you make a decision on the purchase.
If you already are a holder of Transition Networks E-FX-HB-0800, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transition Networks E-FX-HB-0800.
However, one of the most important roles played by the user manual is to help in solving problems with Transition Networks E-FX-HB-0800. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transition Networks E-FX-HB-0800 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
