Instruction/ maintenance manual of the product GEV Trane
Go to page of 90
WSHP-SVX01D-EN Models “A” and later Design Sequence Installation Owner Diagnostics Axiom TM Horizontal/Vertical Water-Source Comfort System Models GEH and GEV 6 - 15 Ton 15 - 25 Ton 1/2 - 5 Ton 6 .
© 2004 American Standard Inc. All rights reserved. WSHP-SVX01D-EN Notice NOTICE: Warnings and Cautions appear at appropriate sections throughout this manual. Read these carefully. WARNING -Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
WSHP-SVX01D-EN 3 Contents Installation/Startup/Commissioning 4 Pre-installation Checklist 4 General Information 5 Dimensions/Weights 7 Installation Instructions 48 Electrical Requirements 67 Pre-Start.
4 WSHP-SVX01D-EN WARNING Fiberglass Wool! Product contains fiberglass wool. Disturbing the insulation in this product during installation, maintenance or repair will expose you to airborne particles of glass wool fibers and ceramic fibers known to the state of California to cause cancer through inhalation.
WSHP-SVX01D-EN 5 General Information Unit Nameplate The unit nameplate is located on the outside of the control box access panel at the front of the unit. It includes the unit model number, serial number, electrical characteristics, refrigerant charge, and other pertinent unit data.
6 WSHP-SVX01D-EN (option) Boilerless Control/Electric Heat Systems that do not contain a boiler may contain a boilerless control with electric heat. Trane offers both a facto- ry mounted electric heat option, and a field mounted duct heater option.
WSHP-SVX01D-EN 7 Table 1: Unit weights GEH 60 HZ GEH 50 HZ GEV 60 HZ GEV 50 HZ Shipping Weight with pallet Shipping Weight w/o pallet 006-015 006-012 188 lb (85 kg) 158 lb (71 kg) 018-030 015-024 278 .
8 WSHP-SVX01D-EN Dimensions/Weights Clearance GEH Clearance Dimensions Access to the unit for service pur- poses should be provided at instal- lation. All 1/2 through 5 ton configurations require an 1.
WSHP-SVX01D-EN 9 Dimensions/Weights Clearance GEV 1/2 through 5 Ton Clearance Dimensions (Figure 1) Access to the unit for service purposes should be provided at installation.
10 WSHP-SVX01D -EN Dimensions/W eights Lef t Return/Lef t Suppl y Unit A B C D E F G H J K L NPTI M NPTI NP Q R S 006,009 40" (1016) 20" (508) 15" (381) 20" (508) 15" (381) 6 7/8" (175) 8" (203) 1 1 1/2" (292) 4 1/4" (108) 2 1/8" (54) 1/2" (12.
WSHP-SVX01D-EN 11 Dimensions/W eights Lef t Return/Bac k Suppl y Unit A B C D E F G H J K L NPTI M NPTI NP Q R S 006,009 40" (1016) 20" (508) 15" (381) 20" (508) 15" (381) 6 7/8" (175) 8" (203) 1 1 1/2" (292) 4 1/4" (108) 2 1/8" (54) 1/2" (12.
12 WSHP-SVX01D -EN Dimensions/W eights Lef t Return/Right Suppl y Unit 60 HZ Unit 50 HZ ABC DEFG H J K L NPTI M NPTI NP Q R 006-009 006 40" (1016) 20" (508) 15" (381) 20" (508) 15" (381) 6 7/8" (175) 8" (203) 1 1 1/2" (292) 4 1/4" (108) 2 1/8" (54) 1/2" (12.
WSHP-SVX01D-EN 13 Dimensions/W eights Right Return/Lef t Suppl y Unit A B C D E F G H J K L NPT I M NPTI NP Q R S 006,009 40" (1016) 20" (508) 15" (381) 20" (508) 15" (381) 6 7/8" (175) 8" (203) 11 1 / 2 " (292) 4 1/4" (108) 2 1/8" (54) 1/2" (12.
14 WSHP-SVX01D -EN Dimensions/W eights Right Return/Bac k Suppl y Unit A B C D E F G H J K L NPTI M NPTI NP Q R S 006,009 40" (1016) 20" (508) 15" (381) 20" (508) 15" (381) 6 7/8" (175) 8" (203) 1 1 1/2" (292) 4 1/4" (108) 2 1/8" (54) 1/2" (12.
WSHP-SVX01D-EN 15 Dimensions/W eights Right Return/Right Suppl y Unit A B C D E F G H J K L NPTI M NPTI NP Q R S 006,009 40" (1016) 20" (508) 15" (381) 20" (508) 15" (381) 6 7/8" (175) 8" (203) 1 1 1/2" (292) 4 1/4" (108) 2 1/8" (54) 1/2" (12.
16 WSHP-SVX01D -EN Dimensions/W eights Lef t Return/T op Suppl y Unit GEV AB C D E F G H J K L M N W. I . NPTI W. O . NPTI Drain FPT 006-015 19 1/2" (495) 31 1/4" (794) 21 1/2" (546) 1 .
WSHP-SVX01D-EN 17 Dimensions/W eights Lef t Return/Bac k Suppl y Unit GEV AB C D E F G H J K L M N W. I . NPTI W. O . NPTI Drain FPT 006-015 19 1/2" (495) 31 1/4" (794) 21 1/2" (546) 1 .
18 WSHP-SVX01D -EN Dimensions/W eights Right Return/T op Suppl y Unit GEV AB C D E F G H J K L M N W. I . NPTI W. O . NPT I Drain FPT 006-015 19 1/2" (495) 31 1/4" (794) 21 1/2" (546) 1.
WSHP-SVX01D-EN 19 Dimensions/W eights Right Return/Bac k Supply Unit GEV AB C D E F G H J K L M N W. I . NPTI W. O . NPTI Drain FPT 006-015 19 1/2" (495) 31 1/4" (794) 21 1/2" (546) 1 1.
20 WSHP-SVX01D -EN Dimensional Data GEH-Right Return/Lef t Suppl y GEH 072-1 20 (60 Hz) GEH 60 Hz GEH 50 Hz ABC D 072 - 36 1/4" (921) 15 5/8" (397) 6 5/8" (168) 1 1/4" (32) 090 0 7.
WSHP-SVX01D-EN 21 Dimensional Data GEH-Right Return/Bac k Supply GEH 072-1 20 (60 Hz) GEH 60 Hz GEH 50 Hz AB C D 072 - 36 1/4" (921) 15 5/8" (397) 6 5/8" (168) 1 1/4" (32) 090 072 .
22 WSHP-SVX01D -EN Dimensional Data GEH-Lef t Return/Right Suppl y GEH 072-1 20 (60 Hz) GEH 60 Hz GEH 50 Hz ABC D 072 - 36 1/8" (917) 17" (432) 8" (203) 1 1/4" (32) 090 072 36 1/8&.
WSHP-SVX01D-EN 23 Dimensional Data GEH-Lef t Return/Bac k Suppl y GEH 072-1 20 (60 Hz) GEH 60 Hz GEH 50 Hz ABC D 072 - 36 1/8" (917) 17" (432) 8" (203) 1 1/4" (32) 090 072 36 1/8&q.
24 WSHP-SVX01D -EN Dimensional Data GEH-Right Return/Lef t Suppl y GEH 1 50-1 80 (60 Hz) GEH 1 20-1 5 0 (50 Hz).
WSHP-SVX01D-EN 25 Dimensional Data GEH-Right Return/Bac k Supply GEH 1 50-1 80 (60 Hz) GEH 1 20-1 5 0 (50 Hz).
26 WSHP-SVX01D -EN Dimensional Data GEH-Lef t Return/Right Suppl y G E H 15 0 - 18 0 ( 6 0 H z ) GEH 1 20-1 50 (60 Hz).
WSHP-SVX01D-EN 27 Dimensional Data GEH-Lef t Return/Bac k Suppl y GEH 1 50-1 80 (60 Hz) GEH 1 20-1 5 0 (50 Hz).
28 WSHP-SVX01D -EN Dimensions/W eights F r ont Return/Bac k Suppl y Unit Size A B C 6 T on 6 5/8" (168) 18 3/8" (467) 1 1/4" 7. 5 T o n 6 5/8" (168) 18 3/8" (403) 1 1/4" .
WSHP-SVX01D-EN 29 Dimensions/W eights F r ont Return/T op Suppl y Unit Size A B C 6 T on 6 5/8" (168) 18 3/8" (467) 1 1/4" 7. 5 T o n 6 5/8" (168) 18 3/8" (403) 1 1/4" 10.
30 WSHP-SVX01D -EN Dimensions/W eights Bac k Return/Fr ont Suppl y Unit Size A B C 6 T on 6 5/8" (168) 18 3/8" (467) 1 1/4" 7. 5 T o n 6 5/8" (168) 18 3/8" (403) 1 1/4" 1.
WSHP-SVX01D-EN 31 Dimensions/W eights Bac k Return/T op Suppl y 6 - 10 Ton (60 HZ) Unit Size A B C 6 T on 6 5/8" (168) 18 3/8" (467) 1 1/4" 7.
32 WSHP-SVX01D -EN 12 1/2 and 15 Ton (60 HZ) and 10 and 12 1/2 Ton (50 HZ) Dimensions/W eights F r ont Return/Bac k Suppl y.
WSHP-SVX01D-EN 33 12 1/2 and 15 Ton (60 HZ) and 10 and 12 1/2 Ton (50 HZ) Dimensions/W eights Bac k Return/F r ont Suppl y.
34 WSHP-SVX01D -EN 12 1/2 and 15 Ton (60 HZ) and 10 and 12 1/2 Ton (50 HZ) Dimensions/W eights F r ont Return/T op Suppl y.
WSHP-SVX01D-EN 35 12 1/2 and 15 Ton (60 HZ) and 10 and 12 1/2 Ton (50 HZ) Dimensions/W eights Bac k Return/T op Suppl y.
36 WSHP-SVX01D -EN 20 and 25 Ton (60 HZ) and 15 and 20 Ton (50 HZ) Dimensions/W eights F r ont Return/Bac k Suppl y Unit 60 HZ Unit 50 HZ ABCDE 20 T on 15 T o n 15 5/8" (397) 13 1/2" (341) 1.
WSHP-SVX01D-EN 37 20 and 25 Ton (60 HZ) and 15 and 20 Ton (50 HZ) Dimensions/W eights Bac k Return/F r ont Suppl y Unit 60 HZ Unit 50 HZ ABCD E 20 T on 15 T o n 15 5/8" (397) 13 1/2" (341) 1.
38 WSHP-SVX01D -EN 20 and 25 Ton (60 HZ) and 15 and 20 Ton (50 HZ) Dimensions/W eights F r ont Return/T op Suppl y Unit 60 HZ Unit 50 HZ AB CD 20 T on 15 T on 15 5/8" (397) 13 1/ 2" (341) 12.
WSHP-SVX01D-EN 39 20 and 25 Ton (60 HZ) and 15 and 20 Ton (50 HZ) Dimensions/W eights Bac k Return/T op Suppl y Unit 60 HZ Unit 50 HZ ABCD 20 T on 15 T on 15 5/8" (397) 13 1/2" (341) 12".
40 WSHP-SVX01D -EN Model GEH Dimensions/W eights W ater side Economizer Unit 60 HZ Unit 50 HZ A NPTI B NPTI CDE FGH J K LMN Filter Size (nominal) 006-015 006-012 1/2" (12.7) 1/2" (12.7) 16 1/8" (410) 13 5/8" (346) 1 1/2" (38) 10 3/4" (273) 23" (584) 2 1/4" (57) 7 1/2" (191) 1/2" (12.
WSHP-SVX01D-EN 41 Dimensions/W eights W ater side Economiz er Hanging Unit Unit 60 HZ Unit 50 HZ A B C D E Hanging Weig ht Shipping Weig ht 006-015 006-012 38 3/4" (984) 18 3/4" (476) 21 3/4" (552) 17" (432) 0" 54 lbs (24.5 kg) 84 lbs (38.
42 WSHP-SVX01D -EN Dimensional Data W ater side Economizer GEH 072-1 20, Right Return (60 Hz) GEH 60 Hz GEH 50 Hz ABC DE 072-090 072 1 1/4" (32) 1 3/8" (35) 31" (787) 9 7/8" (251) .
WSHP-SVX01D-EN 43 Dimensional Data W ater side Economiz er GEH 072-1 20, Lef t Return (60 Hz) GEH 60 Hz GEH 50 Hz ABC DE 072-090 072 1 1/4" (32) 1 3/8" (35) 31" (787) 9 7/8" (251) .
44 WSHP-SVX01D -EN Dimensional Data W ater side Economizer GEH 1 50-1 80, Right Return (60 Hz) GEH 1 20-1 50, Right R eturn (50 Hz).
WSHP-SVX01D-EN 45 Dimensional Data W ater side Economiz er GEH 1 50-1 8 0, Lef t Return (60 Hz) GEH 1 20-1 50, Lef t Return (50 Hz).
46 WSHP-SVX01D -EN Dimensions/W eights W ater side Economizer 6 - 10 Ton (60 HZ) 6 and 7 1/2 Ton (50 HZ) Unit Size A B C 6 & 7 1/2 T on 1 3/8" (35) 1 3/8" (35) 4" (1 02) 10 Ton 1 5/.
WSHP-SVX01D-EN 47 Dimensions/W eights W ater side Economiz er Unit 60 HZ Unit 50 HZ A NPTI B I.D. CD OPERA TING WEIGHT 12 1/2, 1 5 T on 1 0, 12 1/2 T on 1 1/2"" (38) 1 5/8" (41) 15 7/8&.
48 WSHP-SVX01D-EN General Installation Checks The checklist below is a summary of the steps required to successfully in- stall a commercial unit. This checklist is intended to acquaint the installing personnel with what is required in the installation process.
WSHP-SVX01D-EN 49 Supply-Air Ductwork Install the 1" (25.4 mm) supply-air duct flange to the vertical and horizontal equipment with the (8) 5/16" (7.
50 WSHP-SVX01D-EN Dual Filtration (GEH 1/2 to 5 ton) The horizontal, GEH model, allows the installer flexibility in design applica- tions such as a dual filtration option. With the dual filtration design, the unit will contain a lower static which trans- lates into a decrease in filter mainte- nance.
WSHP-SVX01D-EN 51 Sound Attenuation Pad For sound sensitive installations, a vi- bration pad (field provided) should be placed beneath the horizontal or verti- cal equipment. For the horizontal unit, the pad should be approximately twice the size of the unit foot print.
52 WSHP-SVX01D-EN Supply/Return Pipe Connections Connect the supply and return hoses to the water-inlet (from supply) and water-outlet (to return) of the unit. For vibration isola- tion, it is rec- ommended that flexible steel braided hoses be in- stalled instead of hard piping the equipment to the main loop system.
WSHP-SVX01D-EN 53 Types of Hose Connections (3) A circuit setter provides a means of manually balancing the water flow to the heat pump. This manual in-line balancing method is accurate up to ±20%. In order to determine flow rate, the user must record both handle posi- tion, and differential pressure drop.
54 WSHP-SVX01D-EN Connecting a Water Regulating Valve The water regulating valve assembly is shipped as a separate item. Connec- tions from the valve assembly to the unit must be made by the installing contractor. IMPORTANT : These valves are not positive shut-off devices.
WSHP-SVX01D-EN 55 Field Installed Power Wiring Power wiring to the equipment must conform to National and Local Electric Codes (NEC) by a professional electrician. WARNING Live Electrical Components! During installation, testing, ser- vicing and troubleshooting of this product, it may be necessary to work with live electrical compo- nents.
56 WSHP-SVX01D-EN Thermostat Location Location of the thermostat or zone sensor is an important element of ef- fective room control. Areas where the thermostat or zone sensor should not be located inc.
WSHP-SVX01D-EN 57 Controls Using 24 VAC There are two factory thermostat op- tions for the dual circuited (6 through 25 ton) equipment. Low voltage con- nection diagrams for deluxe 24 volt control packages for these thermo- stats mounted on 6 through 25 ton equipment sizes are shown in Figure 11 .
58 WSHP-SVX01D-EN Blower Motor Speed-Tap Retrofit (for 1/2 Through 5 Ton Units ONLY) Motors installed in the unit include 4-speed and 3-speed configurations. All voltages include a 4-speed configuration, with the exception of 380V, 415V, 460V which contain a 3-speed arrangement and 575V which contains a 2-speed arrangement.
WSHP-SVX01D-EN 59 Air Flow Adjustment (6 through 25 ton units ONLY) To increase CFM , loosen the turns open set screw on the sheave, and turn the sheave clockwise. To decrease CFM , Loosen the turns open set screw on the sheave, and turn the sheave counterclockwise.
60 WSHP-SVX01D-EN WARNING Hazardous Voltage! Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power can not be inadvertently energized. Failure to disconnect power before servicing could result in death or serious injury.
WSHP-SVX01D-EN 61 8 Thread the bulb and wire through the low voltage hole of the water- source heat pump. Step 8 9 Wire-tie the sensor to the water SUPPLY side of the piping (ON, or BEFORE) the 2-position valve. Step 9 10 Bundle excess sensor wire, and wire tie the bundle neatly.
62 WSHP-SVX01D-EN 19 Field pipe the drain lines of the waterside economizer and wa- ter-source heat pump together prior to installing a condensate trap.
WSHP-SVX01D-EN 63 WARNING Hazardous Voltage! Disconnect all electric power, in- cluding remote disconnects be- fore servicing. Follow proper lockout/tagout procedures to en- sure the power can not be inad- vertently energized. Failure to disconnect power before servic- ing could result in death or seri- ous injury.
64 WSHP-SVX01D-EN Start-up Sequence 1 Set the thermostat to the highest position. 2 Set the thermostat system switch to COOL with the fan control to AUTO. The compressor should NOT run . 3 Reduce the thermostat setting until the compressor, reversing valve, solenoid valve, and loop pump are energized.
WSHP-SVX01D-EN 65 Waterside Economizing Three-Way Valve Specifications The valve body is constructed from forged brass with nickel plating, with the ball and stem constructed of stainless steel. For other information pertaining to the economizing water valve, see the valve’s data plate.
66 WSHP-SVX01D-EN Electrical Requirements E1-Electrical performance Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No. of Compres. Cmp MCC Blower Motor FLA Blower Motor HP Fan Motor Num Minimum Circuit Ampacity Maximum Overcur- rent Protec- tive Device Electric Heat kW Electric Heat Amps 006 115/60/1 6.
WSHP-SVX01D-EN 67 Electrical Requirements E2-Electrical performance (continued) Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No. of Compres. Cmp MCC Blower Motor FLA Blower Motor HP Fan Motor Num Minimum Circuit Ampacity Maximum Overcur- rent Protec- tive Device Electric Heat kW Electric Heat Amps 024 208/60/1 12.
68 WSHP-SVX01D-EN Electrical Requirements E3-Electrical performance (continued) Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No. of Compres. Cmp MCC Blower Motor FLA Blower Motor HP Fan Motor Num Minimum Circuit Ampacity Maximum Overcur- rent Protective Device Electric Heat kW Electric Heat Amps 042 - Hi Static 208/60/1 21.
WSHP-SVX01D-EN 69 Electrical Requirements E4-Electrical performance (continued) Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No. of Compres. Cmp MCC Blower Motor FLA Blower Motor HP Fan Motor Num Minimum Circuit Ampacity Maximum Overcur- rent Protective Device Electric Heat kW Electric Heat Amps GEH 072 208/60/1 38.
70 WSHP-SVX01D-EN Electrical Requirements E5-Electrical performance (continued) Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No. of Compres. Cmp MCC Blower Motor FLA Blower Motor HP Fan Motor Num Minimum Circuit Ampacity Maximum Overcur- rent Protective Device Electric Heat kW Electric Heat Amps GEV 090 208/60/3 28.
WSHP-SVX01D-EN 71 Electrical Requirements E6-Electrical performance (continued) Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No. of Compres. Cmp MCC Blower Motor FLA Blower Motor HP Fan Motor Num Minimum Circuit Ampacity Maximum Overcur- rent Protective Device Electric Heat kW Electric Heat Amps GEH 150 208/60/3 44.
72 WSHP-SVX01D-EN Electrical Requirements E7-Electrical performance (continued) E8-Electrical minimum and maximum Model No. Volts Total FLA Comp RLA (ea) Comp LRA (ea) No.
WSHP-SVX01D-EN 73 Pre-Start Checklist Pre-Start-up Checklist Before energizing the unit, the following system devices must be checked: __ __ Is the high voltage power supply correct and in accordance .
74 WSHP-SVX01D-EN Initial Unit Start-up Note: Start-up for the Terminal Unit Controller (TUC) may be found in WSHP-IOP-1. Start-up for the Tracer ZN510 controller may be found in WSHP-IOP-2. Start-up for the Tracer ZN524 controller may be found in WSHP-PRB002-EN.
WSHP-SVX01D-EN 75 Operating Pressures GENERAL: There are many variables (airflow, air temperatures) in an air conditioning system that will affect operating refrigera nt pressures and temperatures. The charts below shows approximate conditions and is based on air flow at the rated SCFM, entering air at 80.
76 WSHP-SVX01D-EN Operating Data Model GEH/GEV Entering Water Temp, °F Water Flow GPM Cooling Heating Suction Pres- sure, PSIG Discharge Pressure, PSIG Water Temp Rise °F Air Temp Drop °F DB Suction Pressure PSIG Discharge Pressure PSIG Water Temp Drop °F Air Temp Rise °F DB 018 (60 HZ) 015 (50 HZ) 35° 3.
WSHP-SVX01D-EN 77 Operating Data Model GEH/GEV Entering Water Temp, °F Water Flow GPM Cooling Heating Suction Pres- sure, PSIG Discharge Pressure, PSIG Water Temp Rise °F Air Temp Drop °F DB Suction Pressure PSIG Discharge Pressure PSIG Water Temp Drop °F Air Temp Rise °F DB 042 (60 HZ) 036 (50 HZ) 35° 7.
78 WSHP-SVX01D-EN Operation Pressures Operating Data Model GEH/GEV Entering Water Temp, °F Water Flow GPM Cooling Heating Suction Pres- sure, PSIG Discharge Pressure, PSIG Water Temp Rise °F Air Tem.
WSHP-SVX01D-EN 79 Operating Data Model GEH/GEV Entering Water Temp, °F Water Flow GPM Cooling Heating Suction Pressure, PSIG Discharge Pressure, PSIG Water Temp Rise °F Air Temp Drop °F DB Suction Pressure PSIG Discharge Pressure PSIG Water Temp Drop °F Air Temp Rise °F DB 150 (60 HZ) 120 (50 HZ) 35 25.
80 WSHP-SVX01D-EN Operation Pressures Water Pressure Drop Tables 8 and 9 should be used to define feet of head/pressure drop. Please note the feet of pressure (ft/head) provided is at AR I/ISO stan- dard. Note: To calculate feet of head, when using gauges that read in PSIG,multiply PSI by 2.
WSHP-SVX01D-EN 81 Start-up Checklist and Log Installing Contractor: Use this form to thoroughly check-out the system and units before and during start-up. (This form need not be returned to the factory unless requested during technical service support).
82 WSHP-SVX01D-EN Preventive Maintenance Maintenance on the unit is simplified with the following preventive sugges- tions: Filter maintenance must be performed to assure proper operation of the equipment. Filters should be inspect- ed at least every three months, and re- placed when it is evident they are dirty.
WSHP-SVX01D-EN 83 Warranty Information Standard Warranty The standard water-source heat pump warranty is The Trane Company parts-only warranty, running 12 months from startup, not to exceed 18-months from shipment. Extended Warranty The optional extended warranty is a second through fifth year warranty.
84 WSHP-SVX01D-EN WARNING Hazardous Service Procedures! The maintenance and trouble shooting procedures recommended in this section of the manual could result in exposure to electrical, mechanical or other potential safety hazards. Always refer to the safety warnings provided throughout this manual concerning these procedures.
WSHP-SVX01D-EN 85 Troubleshooting Checklist Deluxe Controls Troubleshooting units which contain the deluxe control option may be made easy by using the three LEDs (light emitting diodes). These LEDs are provided for indicating the operating mode of the controller.
86 WSHP-SVX01D-EN 208 V-60 HZ-1 PH Unit Wiring Basic.
WSHP-SVX01D-EN 87 380-420V-50 HZ-3 PH Unit Wiring Deluxe.
88 WSHP-SVX01D-EN 208V-60 HZ-1 PH Unit Wiring ZN510.
WSHP-SVX01D-EN 89 460 V-60 HZ-3 PH Unit Wiring ZN524.
Trane has a policy of continuous product and data improvement and reserves the right to change design and specifications without notice. Literature Order Number WSHP-SVX01D-EN File Number SV-UN-WSHP-SVX01D-0404 Supersedes SV-UN-WSHP-SVX01C-0104 Stocking Location Inland Trane A business of American Standard Companies www.
An important point after buying a device Trane GEV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Trane GEV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Trane GEV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Trane GEV you will learn all the available features of the product, as well as information on its operation. The information that you get Trane GEV will certainly help you make a decision on the purchase.
If you already are a holder of Trane GEV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Trane GEV.
However, one of the most important roles played by the user manual is to help in solving problems with Trane GEV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Trane GEV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
