Instruction/ maintenance manual of the product FCB1010 Behringer
Go to page of 16
Users Manual ENGLISH Version 1.4 M arch 2003 MIDI FOOT CONTROLLER FCB1010.
MIDI FOOT CONTROLLER FCB1010 2 This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosurevoltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature.
MIDI FOOT CONTROLLER FCB1010 3 F C B 1010 MIDI FOOT CONTROLLER Ultra-Flexible MIDI FOOT CONTROLLER with Two Expression Pedals and MIDI Merge Function s 10 banks of presets, each with 10 fully user-edi.
MIDI FOOT CONTROLLER FCB1010 4 FOREWORD Dear Customer, welcome to the team of BEHRINGER users, and thank you very much for expressing your confi- dence in us by pur- chasing the FCB1010 .
MIDI FOOT CONTROLLER FCB1010 5 1. INTRODUCTION Congratulations! With the BEHRINGER MIDI FOOT CONTROLLER FCB1010 you purchased an ultra-flexible controller unit for a wide range of applications, whethe.
MIDI FOOT CONTROLLER FCB1010 6 2. PROGRAMMING THE FCB1010 1.3.2 Rear panel Fig. 1.2: Rear panel connectors FUSE HOLDER / VOLTAGE SELECTOR. Please make sure that your local voltage matches the voltage indicated on the unit, before you attempt to connect and operate the FCB1010.
MIDI FOOT CONTROLLER FCB1010 7 2. PROGRAMMING THE FCB1010 Fig. 2.2: PRESET selection with DIRECT SELECT enabled As this example shows, the DIRECT SELECT feature gives you a faster access to BANKS and PRESETS than without this function. Which option to use is entirely up to you.
MIDI FOOT CONTROLLER FCB1010 8 1 SW I T CH 1 Determines if UP k ey toggles SW I TCH 1 relay while DI RECT SELECT is enabl ed. 2 SW I T CH 2 Determines i f DOW N k ey t oggles SW I TCH 2 relay while DI RECT SELECT is enabl ed. 5 COPY PRESET Enables copying preset s (see c h.
MIDI FOOT CONTROLLER FCB1010 9 s If you have selected EXP A or EXP B , you can now enter the controller number the EXPRESSION PEDAL of your choice is aimed to send values for. Confirm your selection with UP/ENTER and enter the lower value (pedal up). Confirm with UP/ENTER.
MIDI FOOT CONTROLLER FCB1010 10 s Activate the expression pedal you wish to program by keeping the corresponding foot key pressed for a few seconds (foot keys 8 or 9). The foot key LED blinks after you briefly press the foot key yet again. s Confirm with UP/ENTER.
MIDI FOOT CONTROLLER FCB1010 11 2.5 Controller toggle function This function allows you to configure one controller so that it alternately sends two different values, e.g. effect bypass, drive on/off, etc. s In order to enable the controller switch-over function, you need to globally select the same MIDI channel for CNT1 and CNT2 (see chapter 2.
MIDI FOOT CONTROLLER FCB1010 12 Fig. 2.5: Sending a SysEx-Dump 2.7.2 Receiving SysEx dumps To send back FCB1010 data stored on a sequencer/computer before, please follow the instructions below: s Connect the MIDI OUT connector of your sequencer or computer to the MIDI IN connector of the FCB1010 (see fig.
MIDI FOOT CONTROLLER FCB1010 13 s Keep the switches 1 and 3 pressed while powering up the unit. This puts your FCB1010 i nto self-test mode , and all LEDs are being tested. s Please wait until all switch LEDs light up. Then press all the switches, including the UP/ENTER and DOWN/ESCAPE keys, so that all LEDs are turned off.
MIDI FOOT CONTROLLER FCB1010 14 4. MIDIA STANDARD, A REVOLUTION In the early 80s several leading manufacturers of electronic musical instruments developed a common standard, which was soon to revolutionize the entire MI industryboth from a technical and musical point of view.
MIDI FOOT CONTROLLER FCB1010 15 6. SPECIFICATIONS 4.2.4 Running status Since the MIDI standard uses a serial transmission format, i.e. transmits data successively, it was soon found that the transmission rate is too low if the system is exploited to its full capacity.
MIDI FOOT CONTROLLER FCB1010 16 7. WARRANTY The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or transmitted in any form or by any .
An important point after buying a device Behringer FCB1010 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Behringer FCB1010 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Behringer FCB1010 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Behringer FCB1010 you will learn all the available features of the product, as well as information on its operation. The information that you get Behringer FCB1010 will certainly help you make a decision on the purchase.
If you already are a holder of Behringer FCB1010, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Behringer FCB1010.
However, one of the most important roles played by the user manual is to help in solving problems with Behringer FCB1010. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Behringer FCB1010 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
