Instruction/ maintenance manual of the product 95-8211 Toyota
Go to page of 8
INST ALLA TION INSTRUCTIONS FOR P ART 95-8211 95-8211 KIT FEA TURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision A) Double DIN T rim Plate KIT COMPONENTS A Small Flat Blade Screwdriver • Panel Removal T ool • Phillips Screwdriver • Soc k et Set 1-800-221-0932 © COPYRIGHT 2004 METRA ELECTRONICS CORPORA TION www .
Dash Disassembly - T oyota A valon 2000-2004 (column shift models) . . . . . . . . . . . . . . . . . . . . . 1 - T oyota A valon 2000-2004 (console shift models) . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - D o u b l e D I N R a d i o P r o v i s i o n .
95-8211 DA SH DISASSEMBL Y TO Y OT A A V ALON 2000-2004 (column shift models) A B 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 1 Unsnap the trim below the cli- mate control to reveal (2) 10 MM bolts and remove . (Figure A) 2 Car efully pull air vents above radio towar ds rear of car to unsnap.
2 95-8211 DA SH DISASSEMBL Y R F D C B A E TOY OT A A V ALON 2000-2004 (console shift models) Open the center console armrest, unsnap cover above cup holder and remove (2) Phillips screws tow ard the outside of the panel. (Figure A) 2 Lift up and remove shifter trim/ash- tray assembly .
3 95-8211 KIT ASSEMBL Y A/C OFF A DOUBLE DIN RADIO PROVISION Continue to final assembly . * Note: Refer also to the instructions included with the aftermarket radio. Attach the factory mounting brackets and the Double DIN trim plate to the Double DIN radio using the screws supplied with the radio .
4 95-8211 KIT ASSEMBL Y A/C OFF A ST A CKED ISO MOUNT UNITS PROVISION Continue to final assembly . * Note: Refer also to the instructions included with the aftermarket radio. Attach the factory mounting brackets and the Double DIN trim plate to the stacked ISO Mount units using the screws supplied with the units.
95-8211 FINAL ASSEMBL Y FINAL A SSEMBL Y (A) Strip wire ends back 1/2" B) T wist ends together C) Solder D) T ape A B C D Locate the factory wiring har ness in the dash. Metra recommends using the proper mating adapter and making connections as shown.
95-8211 INSTRUCTIONS 1-800-221-0932 REV . 01/03/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-8211 www .metraonline.com.
An important point after buying a device Toyota 95-8211 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toyota 95-8211 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toyota 95-8211 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toyota 95-8211 you will learn all the available features of the product, as well as information on its operation. The information that you get Toyota 95-8211 will certainly help you make a decision on the purchase.
If you already are a holder of Toyota 95-8211, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toyota 95-8211.
However, one of the most important roles played by the user manual is to help in solving problems with Toyota 95-8211. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toyota 95-8211 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
