Instruction/ maintenance manual of the product X300 Toshiba
Go to page of 231
GMAD00181012 08/08 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 164 in this gui de.
2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical ap.
4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n.
5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can.
6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer .
7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.
8 5.375 x 8.375 ver 2.3 In some situations or en vironments, the use of W ireless LAN may be restricted by the proprietor of the b uilding or responsible representativ es of the organization.
9 5.375 x 8.375 ver 2.3 The term “IC” before the equipment certif ication number only signifies that the Industry Canada technical specifications were met. T o prev ent radio interference to the licensed service, this device is intended to be operated indoors an d away from windo ws to pr ovide maximum shielding.
10 5.375 x 8.375 ver 2.3 The European Union WEEE (W as te from Electrical and Electronic Equipment) Directive Information The European Union WEEE (W aste from Electrical and Electronic Equipment) Dire.
11 5.375 x 8.375 ver 2.3 Howe ver , due to differences between the individual P STNs provided in diff erent countries/re gions the approv al does not, of itself, gi v e an unconditional assurance of successful operation on ev er y PSTN network termination point.
12 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. O F: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m.
13 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on wha t type of wi reless device is in your computer . Not all devices are available on all models. Approved Countries/Regions for use for the Atheros AR5BXB72 2.
14 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special registration with IBPT/BIPT is required.
15 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply .
16 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Atheros AR5BXB63 11g minicard This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
17 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
18 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
20 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that.
21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table.
22 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization.
23 5.375 x 8.375 ver 2.3 Ta i w a n The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations.
24 5.375 x 8.375 ver 2.3 2. Indication The indication shown belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.
25 5.375 x 8.375 ver 2.3 Optical Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model prop erly , read th e user’ s guide carefully and keep it for your fut ure reference.
26 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approval of the U.S. Department of Commerce prior to expor t.
27 5.375 x 8.375 ver 2.3 T rademarks Qosmio is a registered trademark of T oshib a America Information Systems, Inc. and/or T oshiba Corporation. Microsoft, Outlook, Windo ws, and Wi ndo ws V ist a are either registered trademarks or trademarks of Microsoft Corporatio n in the United States and/or other countries.
28 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 35 This guide ...............................................................37 Safety icons ............................
29 Contents 5.375 x 8.375 v er 2.3 Charging the main battery ....................................... 48 Using the computer for the first time ......................49 Opening the display panel .................................49 Your computer’s features and specifications .
30 Contents 5.375 x 8.375 v er 2.3 Customizing your co mputer’s settings ....................87 Caring for your computer ........................................87 Cleaning the computer ......................................88 Moving the computer ..
31 Contents 5.375 x 8.375 v er 2.3 Chapter 3: Mobile Computin g ........................... ...................... 106 Toshiba’s energy-saver design..............................106 Running the computer on battery power ..............106 Battery Notice .
32 Contents 5.375 x 8.375 v er 2.3 Surfing the Internet .........................................130 Internet features ..............................................130 Uploading to, and downloading files from, the Internet ...........................
33 Contents 5.375 x 8.375 v er 2.3 Fingerprint utility limitations ...........................157 Using the Fingerprint Authentication Utility .....157 Fingerprint Logon ...........................................158 Care and maintenance of your fingerprint reader .
34 Contents 5.375 x 8.375 v er 2.3 If you need further assistance ............................... 192 Before you contact Toshiba ............................192 Contacting Toshiba .........................................193 Other Toshiba Intern et Web sites .
35 5.375 x 8.375 ver 2.3 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our Comp uter model may be ENERGY ST AR ® com pliant.
36 Introd uctio n 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would sav e more than $1.
37 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated.
38 Introd uctio n Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data.
39 Introduction Other documentation 5.375 x 8.375 ver 2.3 Other documentation Y our co mputer comes with t he following documentation: ❖ An electronic version of the user’ s guide (this docum ent) ❖ It may also contain guides for other programs that may come with your system.
40 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information.
41 Getting Started Selecting a place to work T o keep your computer in prime operating condition, pro tect your work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
42 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin.
43 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our co mputer may have a CPU cooling fan that cools t he CPU by drawing outside air into the computer .
44 Getting Started Setting up your computer Please handle your computer carefully to avo id scratching or damaging the surface. Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely .
45 Getting Started Re gistering your computer with T oshib a Registering your computer with T oshiba Product registration is strongly reco mmended, and allows T oshiba to send you periodic updates, announcement s, and special offers applicable to your p roduct.
46 Getting Started Connecting to a power so ur ce Connecting to a power source Y our comp uter requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery .
47 Getting Started Connecting to a po wer sour ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to t.
48 Getting Started Char ging the main battery ❖ Glows red when the main battery is fully char ged ❖ Is unlit when t he main battery has d ischarged, the battery is not charging, or the A C adaptor.
49 Getting Started Using the computer for the f irst time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and be gin using it.
50 Getting Started Using the computer for the fir st time Small bright dots ma y appear on your screen display wh en you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology .
51 Getting Started Adding memory (optional) 3 Press and release the power b utton. The on/off light glo ws red. (Sample Illustration) T urning on the power The preinstalled operating syst em will load automatically . When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely .
52 Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memory mo dule slots on the base of the computer . Y ou will need a small Phillips scr e wdriv er for this procedure. If the computer has been running recently , the memory module may be hot.
53 Getting Started Adding memory (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start , and then click the arrow ne xt to the lock button in the lower -right corner of the Start menu. The Shut Down menu appears.
54 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre w that secures the memory module slot cover . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cov er .
55 Getting Started Adding memory (optional) For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 11 Pick up the memory module by its sides, av oiding any contact with its connector .
56 Getting Started Adding memory (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module.
57 Getting Started Adding memory (optional) 14 Replace the memory modu le slot cov er and secure it using the screw . 15 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 118 .
58 Getting Started Adding memory (optional) The following screen may appear when you turn on the power: If “Start Windows ® Normally” is highlighted, then press Enter .
59 Getting Started Adding memory (optional) 4 Replace the memory modu le slot cov er and secure it using the screw . 5 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 118 .
60 Getting Started Har d Drive Recovery Utilities Hard Drive Recovery Utilities Y our computer has been configured with a hard disk partition to allow you to recov er your hard di sk drive or reinstall selected applications and software features or utilities.
61 Getting Started Har d Drive Recovery Utilities T o create recov ery D VDs: 1 Click Start , All Programs , To s h i b a , Recovery , and then Recovery Disc Creator .
62 Getting Started Har d Drive Recovery Utilities Hard Disk Drive Recovery using the recover y partition During the HDD Recovery Process it is strongly recommended that your computer be connected to an external power source via the AC Adaptor .
63 Getting Started Har d Drive Recovery Utilities ❖ Erase the hard disk (Sample Image) T oshiba Recovery W izard scr een Recovering the original factor y image (recommended recover y method) Recovering a hard disk drive to its out of box state deletes all parti tions on the hard disk drive and you r information will be lost.
64 Getting Started Har d Drive Recovery Utilities 2 Select Recover to out-of-box-state , and then click Next . A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to sa ve your work to ex ternal media before proceeding.
65 Getting Started Har d Drive Recovery Utilities (Sample Image) Er ase the har d disk scr een 3 Select the desired method, and then click Next . A confirmation message displays reminding you that all data will be lost. Be sure you hav e sav ed your work to e xternal media before proceeding.
66 Getting Started Har d Drive Recovery Utilities 2 Select Recover without changing the hard drive partitions . A confirmation message appears, reminding you that all information on the C: driv e will be lost during the recovery process. Be sure you hav e sav ed your work to e xternal media before proceeding.
67 Getting Started Har d Drive Recovery Utilities 2 When the initial screen displays, press F12 . The boot menu appears. 3 Using the arro w keys, select the D VD option and press Enter . 4 The Selecting a Process S creen will appear . Select one of the options an d then click Next .
68 Getting Started Har d Drive Recovery Utilities 6 A warning screen will appear stat ing that when the reco very is ex ecuted all data will be deleted and rewritten. Click Ye s to continue. (Sample Image) W arning screen 7 The T oshiba Recovery W izard screen will appear .
69 Getting Started Using the T ouchP ad™ Checking the HDD operating status After restoring your hard disk driv e, you can check its status as follows: 1 Click Start .
70 Getting Started Using the T ouchP ad™ ❖ T o move it to the left side, slid e your finger from right to left . Because the T ouchPad is much smaller than the display screen, moving your cursor acros s the screen often means having to move your finger several times across the T ouchPad in the preferred direction.
71 Getting Started Using external display de vices Using external display devices Y our computer comes with a built-in display , but you can also connect the following types of external display de vic.
72 Getting Started Using external display de vices Y our computer will automaticall y detect the external display devic e and activ ate a screen w ith display optio ns.
73 Getting Started Using external display de vices ❖ Using the S/PDIF jack on the si de of the co mputer—This lets you connect to a sound system that can accept the digital optical signal from your com put er . Y ou need an S/PDIF cable (not included with yo ur computer) with a T oslink 1/8" (3.
74 Getting Started Using external display de vices Directing the display output when you turn on the computer Once you connect an external display de vice, you can choose to use the internal display only , the external de vice only , or both simultaneously .
75 Getting Started Using an external k e yboard The right-most icon in the above illustration is for the Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-in Display and External Monitor , or Built-in Display and TV).
76 Getting Started Connecting a printer If your printer sup ports Plug and Play , your computer may automatically recogni ze the printer; th e printer is then ready for use. Refer to your printer docum entation for further in structions. TECHNICAL NOTE: T o determine if your printer supports Plug and Play , check its documentation.
77 Getting Started Connecting an optional external disk ette drive Connecting an optional external diskette drive Some operations, such as creati ng a password service disk ette, require a diskette dri ve designed for use with 3.
78 Getting Started T urning off the computer Options for turning off the computer Depending on the operating sy stem installed, you have more than one option av ailable for turning off the computer: Shut Down, Hibernate, and Sleep. Each option has its advantages.
79 Getting Started T urning off the computer For information on ho w to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 82 .
80 Getting Started T urning off the computer Using the Shut Down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns off your computer .
81 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options scr een 4 Click Power buttons and lid to display the actions that you can configure.
82 Getting Started T urning off the computer Once the computer is conf igured, you can turn it off b y either pressing the power b utton or closing the display panel, depending on the options set . Restarting your computer T o start the computer up again, press the po wer b utton unti l the on/off light glows red.
83 Getting Started T urning off the computer T o use any of these methods, you f irst need to enable them using the Power Options feature. 1 Click Start , Contro l Panel , System and Maintenance , and then Po wer Options . The Po wer Options window appears.
84 Getting Started T urning off the computer ❖ Po wer button action Set this option to Hibernate if you want the computer to go into Hibernation mode wh en you press the power button. ❖ Start menu po wer button Set this option to Hibernate if you want the computer to go into Hibernation mode wh en you click the power button in the Start men u.
85 Getting Started T urning off the computer 2 Click Sleep . The computer sa ves the status of all open programs and files to the memory , turns off the display , and enters into a low-po wer mode. The on/off light blinks amber indicating the computer is in Sleep mode.
86 Getting Started T urning off the computer 4 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. (Sample Image) Advanced settings tab of P ower Options screen 5 Click Power buttons and lid to display the actions that you can configure.
87 Getting Started Customizing your computer’ s settings 7 Click App l y . 8 Click OK . Once the computer is conf igured, you can place it into Sleep mode by either pressing the po wer button or closing the display panel, depending on the Sleep options set.
88 Getting Started Caring for your computer Cleaning the computer Keep liquids, including cleaning fluid, out of the computer’ s keyboard, speaker , and other openings. Never spray cleaner directly onto the computer and/or display . Never use harsh or caustic chemical products to clean the computer .
89 Getting Started Caring for your computer 2 Pass the locking end through the loop. 3 Insert the cable’ s locking end into the security lock slot on your computer , then engage the locking de vice.
90 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive.
91 Learning the Basics Computing tips ❖ Back up your files to disks (or other remov able media) on a regular basis. Label the backup co pies clearly and store them in a safe place.
92 Learning the Basics Using the ke yboar d Using the keyboard Y our co mputer’ s ke yboard contai ns character keys, control ke ys, function ke ys, and special W indo ws ® keys.
93 Learning the Basics Starting a pr ogr am Function keys The function k eys (no t to be confused with the Fn key) are the 12 keys at the top of the k eyboard. (Sample Illustration) Function ke ys F1 through F12 are called function keys because the y ex ecute programmed functions when pressed.
94 Learning the Basics Starting a pr ogra m Starting a program from the Start menu When you install a prog ram, the operating syst em usually puts an icon in the Al l Programs menu.
95 Learning the Basics Starting a pr ogr am 5 In the left part of the window , c lick the line that ends in “Local Disk (C:). ” 6 In the left part of the window , under the Local Disk C: icon, double-click the folder contai ning the program, in this case Program Files .
96 Learning the Basics Saving your work Saving your work Before you turn off the computer using the Shut Down command, sav e your work on the internal storage driv e, diskette, flash media, or optical disc. This is one of the most important rules of computing.
97 Learning the Basics Printing your work HINT : T o make another copy of the file you are currently working with, click File , and then Save As , and give the new file a different name. File names The W indo ws ® operating system supp orts long file names that can contain up to 260 characters and can include spaces.
98 Learning the Basics Backing up your work 2 In your W indows ® -based application, click File , and then Print . The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters. For e xample, the range of pages and number of copies to print.
99 Learning the Basics Using the optical drive Restoring your work T o restore information from your backu p media to your internal storage dri ve, use the Restore page in t he backup program. Look in the online Help or your op erating system documentation for information on restoring files.
100 Learning the Basics Using the optical drive When viewing DVD movies use the DVD Player software that came with your computer . Optical drive components The optical dri ve is located on the side of the computer .
101 Learning the Basics Using the optical drive Media control buttons The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or D VD movies when the computer is on.
102 Learning the Basics Using the optical drive Inserting an optical disc T o insert an optical disc into the dri ve: 1 Make sure the computer is turned on. The dri ve will not open if the computer’ s power is of f. 2 Make sure the dri ve’ s in-use indicator light is off.
103 Learning the Basics Using the optical drive Handle DVDs and CDs carefully , making contact only with the center hole and edge. Do not touch the surface of the disc. Do not s tack discs. If you incorrectly handle the discs, you c ould lose data. 8 Make sure the disc is completely on the spindle and is lyin g flat on the tray .
104 Learning the Basics Using the optical drive Recording optical media Depending on the configuration, your computer may come with an optical driv e that allows you to: ❖ Play pre-recorded and recorded optical media. ❖ Read/write data and multi -media files to recordable optical media.
105 Learning the Basics T oshiba’ s online r esour ces Removing a disc with the computer off T o remov e a disc with the computer turned of f: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole. The disc tray slides partially out of the dri ve (about 1 inch).
106 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your comput er while trav eling. T oshiba’ s energy-saver design Y our co mputer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process.
107 Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specif ications depending on product model, configuration, applications, power management settings and features utilized, as well as th e natural performance variations produced by the design of indi vidual components.
108 Mobile Computing Char ging batteries Power management Y our co mputer ships with t he power management options preset to a configuration that will prov ide the most stable opera ting en vironment and optimum system performan ce for both A C po wer and battery modes.
109 Mobile Computing Char ging ba tteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet.
110 Mobile Computing Monitoring main battery power If the R TC battery is lo w , the real-time clock and calendar may display the incorrect tim e and date, or stop working. T o recharge the R T C battery , plug the computer into a li ve electrical outlet and leav e the computer powered on for 24 hours.
111 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the batter y light ( ), the on/off light ( ), and the power button light. When the on/off light or power button light flashes amber , it indicates that the system is suspended (us ing the Windows ® operating system Sleep command).
112 Mobile Computing Monitoring main battery power Highlight the power icon in the Notification Area. A pop-up message displays the remaining battery power as a percentage. W ith repeated discharges and rechar ges, the battery’ s capacity gradually decreases.
113 Mobile Computing Monitoring main battery power T o change the default notification settings: 1 Click Start , Contro l Panel , Mobile PC , and th en Power Options . The Po wer Options window appears. 2 Click Change plan s ettings under the po wer plan to be customized.
114 Mobile Computing Monitoring main battery power There are v arious ways in which you can conserv e power a nd extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves.
115 Mobile Computing Monitoring main battery power T o edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change Plan Se ttings to choose the plan you want to edit.
116 Mobile Computing Changing the main battery 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: Balanced, Po wer Sa ver , and High Performance. 3 Release the Fn key . The hot ke y card disappears.
117 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease lock 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer .
118 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks.
119 Mobile Computing T aking car e of your battery 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 116 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on ho w to take care of your battery and prolong its life.
120 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
121 Mobile Computing Disposing of used batteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main batt ery light flashes amber shortly after you hav e fully rech arged the battery .
122 Mobile Computing T raveling tips T o shiba is dedicated to preservi ng the en vironment by sponsoring Call2Recycle™ , a program of the Rechar geable Battery Recycling Cor por atio n. For more information and for drop-off locations, visit www .rbrc.
123 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system.
124 Exploring Y our Computer’ s Features Explorin g the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, T askb ar , Notification Area, and background pattern.
125 Exploring Y our Computer’ s Features Exploring the desktop Y our de sktop may contain other icons dependi ng on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it.
126 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines wit.
127 Exploring Y our Computer’ s Features Setting up for communications Accessing a network T o access a network: ❖ At the of fice, c onnect an Ethern et cable to the RJ45 jack on your computer . For specific info rmation about connecting to the network, consult your netw ork administrator .
128 Exploring Y our Computer’ s Features Setting up for communications Before you can communicate using th e modem, you need to connect it to a telephone line. Y ou r computer’ s b uilt-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line.
129 Exploring Y our Computer’ s Features An overview of using the Internet An overview of using the Internet The following sections giv e a quick introduction to t he Internet and some of its exciti.
130 Exploring Y our Computer’ s Features An overview of using the Internet Connecting to the Internet T o connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A W eb browser ❖ An Internet Service Provider (ISP) account Once you hav e established an ISP account, you can connect to the Internet.
131 Exploring Y our Computer’ s Features Explorin g audio featur es ❖ Internet chat roo ms A chat room is a W eb site that offers a pla ce where people with similar interests and ideas comm unicate in real-time, one-on- one or in groups, by typing messages which are instantly viewed by others on their computer screens.
132 Exploring Y our Computer’ s Features Explor ing audio feat ur es 2 Click Start , All Programs , Acces sories , and then Sound Recorder . (Sample Image) Soun d Recor der scr een 3 Click the Start Recording button. 4 Speak normally into the microphon e.
133 Exploring Y our Computer’ s Features FM tuner FM tuner (A vailable on certain models) Y our computer may come equipped with a built-in FM tuner and a separate FM antenna. With this FM tuner feature you can listen to li ve local FM radio stations.
134 Exploring Y our Computer’ s Features Using an Expr essCard ® The W eb Camera soft ware, by default, should already be running in the Notification Area.
135 Exploring Y our Computer’ s Features Using the Bridge Media Adapter Slot 3 Grasp the ExpressCard an d pull it straight out. (Sample Illustration) Removing an Expr essCard Using the Bridge Media .
136 Exploring Y our Computer’ s Features Using the i.LINK ® port When inserting memory media, do not touch the metal contacts. Y ou could expose the storage area to static electri city , which can destroy data.
137 Chapter 5 Utilities Y our comp uter includes sev eral utilities designed to help you to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns.
138 Utilities TOSHIB A Assist TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings. T o access TOSHIB A Assist, click Start , All Programs , To s h i b a , Utilities , and then TOSHIB A Assist .
139 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings ❖ Bluetooth ® Local COM Setting s (Sample Image) .
140 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secur e tab.
141 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility (Sample Image) T OSHIBA Assist window – Pr otect & Fi x tab.
142 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Setup ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ CD/D V.
143 Utilities Setting passwor ds Setting passwords Setting a password lets you walk aw ay from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again.
144 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to se.
145 Utilities Setting passwor ds 6 Click OK . A pop-up screen ap pears asking for the User Password Mode. 7 Select whether the user password allo ws the user to change the hardware configuration: ❖ .
146 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , To s h i b a , Utilit ies , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab .
147 Utilities TOSHIB A PC Dia gnostic T ool Utility 4 Click Not Registered. A pop-up screen ap pears asking for a password. 5 Enter the user password, then click OK . TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose problem s with devices in your computer .
148 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contr ol Panel , and then Mouse under Hard ware and Sound , or click the Mouse icon in the Optimize tab of TOS HI BA A ss is t .
149 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshiba configuration management tool av ailable through th e W indows ® operating system.
150 Utilities TO S H I B A H a rd w a re S e t u p ❖ CPU —Allows you to enable or disable CPU frequency switching modes Dynamically Swit chable —This mode is th e default setting for your comput.
151 Utilities TO S H I B A H a rd w a re S e t u p Ho wev er , the “USB Sleep and Char ge function” may not w ork with certain external devices ev en if they are compliant with the USB specification. In those cases, turn the power of the computer ON to charge the de vice.
152 Utilities TO S H I B A H a rd w a re S e t u p USB Sleep and Char ge function Settings —The default setting is Disabled. Changing the settin g to Enabled enables the use of this function. T o change the setting, launch TOSHIB A Hardware Setup and click on the USB tab .
153 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 209 ).
154 Utilities TOSHIB A Button Support The zoom in and zoom out hot keys will now w ork with the applications you selected. T o zoom in, hold down the Fn key and press 2 ; to zoom out, hold down the Fn ke y and press 1 .
155 Utilities CD/D VD Drive Acousti c Silencer CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical driv e to make it run more quietly .
156 Utilities TOSHIB A Accessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required.
157 Utilities F ing erprint Au thentication Utility Fingerprint Authentication Utility (A vailable on certain models) The fingerprint authentication utility (av ailable on certain models) can be used to replace the ke yboard-based user password authentication syst em when booti ng up.
158 Utilities F ing erprint Authenticati on Utility Fingerprint Logon The fingerprint utility enables logon to your comp uter using fi ngerprints. During us er enrollment, f ingerpr int samples are sav ed and associated with the user’ s W indows ® user account.
159 Utilities F ing erprint Au thentication Utility ❖ A void the follo wing finger conditions for enrollment or recognition as they may result in fingerprint enrollment erro rs or a drop in the f ingerprint recognitio n success rate. ❖ Soaked or swollen fi nger (e.
160 Utilities ConfigF r ee® ❖ The recognition success rate may dif fer from user to user . ❖ T oshiba does not guarantee that this fingerprint recognition technology will be error -free. T oshiba does not guarantee that the f ingerprint reader will recognize the enrolled user or accu rately screen out unauthorized users at all times.
161 Utilities ConfigF r ee® Starting ConfigFree ® T o start ConfigFree ® , be sure the computer has a wired or wireless connection. Then perform any of the follo wing steps: ❖ Click Start , All Programs , To s h i b a , Networking , and then Conf igFree .
162 Utilities ConfigF r ee® ❖ Status of W ireless Connection switch (Sample Image) Connect ivity Doctor scr een Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices.
163 Utilities ConfigF r ee® T o create a profile: 1 Click the icon in the Notif ication Area. 2 Mov e the pointer to Prof ile . 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF r ee Prof ile Settings window 4 Click Add to start the Create Prof ile W izard.
164 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself.
165 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask .
166 If Something Goes Wrong Pr oblems when you turn on the computer If you are using an A C adaptor , v eri fy that the computer is recei ving power from the external po wer source by looking at the A C power light. If the indicator is glo wing, th e computer is conn ected to a liv e external po wer source.
167 If Something Goes Wrong Pr oblems when you turn on the computer If you are running on battery power , it is recommended that you do not lea ve the computer in Sleep mode for lo ng periods of time. T o charge the battery , leav e the computer plugged into a li v e wall outlet for sev eral hours.
168 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the A C adaptor is th e correct unit for your computer model.
169 If Something Goes Wrong The W indo ws ® operating system is not working ❖ Safe Mode with Command Pr ompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Kno wn Good C.
170 If Something Goes Wrong Resolving a hardwar e conflict The Windows ® operating system can help you If the operating system has started properly but you still ha ve a problem using your co mputer , the online Help can assist you in troubleshooting the pro blem.
171 If Something Goes Wrong Resolving a har dwar e conflict The device most recently connected to the system is th e one most likely to be causing a conflict. Resolving conflicts There are sev eral things you can do to resolve hardw are conflicts: ❖ Get the most recent dri vers from the manuf acturer .
172 If Something Goes Wrong Resolving a hardwar e conflict ❖ The Resources tab, which lists resources assigned to the monitor , optional external opti cal driv e, optional external diskette dri ve, and other power -using functions. This tab does not appear if the device is not using resources.
173 If Something Goes Wrong Resolving a har dwar e conflict For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A.
174 If Something Goes Wrong Resolving a hardwar e conflict The battery appears not to power the computer f or as long as it usually does. If you frequently repeat shallow char ge and disch a rge, the battery meter may become in accurate. Let the battery discha rge completely , then try charging it ag ain.
175 If Something Goes Wrong Resolving a har dwar e conflict Display problems Here are some typical displ ay problems and their sol utions: The screen is blank. Display Auto Off may ha ve gone into ef fect. Press any ke y to acti vate the screen. Y ou may have acti v ated the instan t password feature by pressing Fn and F1 simultaneously .
176 If Something Goes Wrong Resolving a hardwar e conflict The built-in scr een flickers. Some flickering is a normal result of the way the screen produces colors. T o reduce the am ount of flickering, try using fe wer colors. T o change the number of colors displayed: 1 Right-click in a blank area of the W indo ws ® desktop.
177 If Something Goes Wrong Resolving a har dwar e conflict Disk or internal storage drive problems Problems with the internal storage dri ve or with a diskette dri ve usually sho w up as an inability to access the driv e or as sector errors. Somet imes a dri ve pr oblem may cause one o r more f iles to appear to hav e garbage in them.
178 If Something Goes Wrong Resolving a hardwar e conflict Y our data files are damaged or corrupted. Refer to your software documentation for file recov ery procedures. Many software packages auto matically create backup files. Y ou may also be able to recover lost data using utility software.
179 If Something Goes Wrong Resolving a har dwar e conflict Y ou press the disc eject b utton, but the drive tray does not slide out. Make sure the computer is connect ed to a po wer source and turned on. The optical dri ve eject me chanism requires po wer to operate.
180 If Something Goes Wrong Resolving a hardwar e conflict The computer emits a loud , high-pitched noise. This is feedback between the mi crophone and the speakers. It occurs in any sound system when i nput from a micropho ne is fed to the speakers and the speak er volume is too loud.
181 If Something Goes Wrong Resolving a har dwar e conflict 2 Double-click the appr opriate ExpressCard, which w ill be listed under one of the categories sho wn, for example: Disk driv es, Network adapters, Other , etc.
182 If Something Goes Wrong Resolving a hardwar e conflict An ExpressCard ® er ro r occurs. Reinsert the card to make sure it is properly connected. If the card is attached to an e xternal device, check that the connection is secure. Refer to the card’ s documentation, which should contain a troubleshooting section.
183 If Something Goes Wrong Resolving a har dwar e conflict Modem problems (A vailable on certain models) This section lists comm on modem problems. The modem will not r eceive or transmit pr operly . Make sure the cable from the modem to the telephone line is firmly connected to the computer’ s modem port and the telephone line jack.
184 If Something Goes Wrong Resolving a hardwar e conflict T o determine if your computer has an internal Wi-Fi ® adapter , check the device list in Device Manager (part of the Windows ® Control Panel, Hardware and Sound). Some T oshiba models may have a Wireless antenna ON/OFF switch even though they do not have an internal Wi-Fi ® adapter .
185 If Something Goes Wrong Resolving a har dwar e conflict 3 At the top-left of the Start menu, click cmd.exe to open the command prompt. 4 Enter IPCONFIG / ALL and press Enter .
186 If Something Goes Wrong D VD operating pr oblems DVD operating problems If you experience a problem playing D VDs, you may be able to fix the problem yourself. For general problems playing a D VD title, try the following steps: 1 V erify that the disc is in a format that the dri ve supports.
187 If Something Goes Wrong Develop good computing habits Develop good computing habits Sa ve y our work fr equently . Y ou can never predict when your co mput er will lock, fo rcing you to close a program and lose unsaved changes. Man y software programs build in an automatic backup, but you should not rely solely on this feature.
188 If Something Goes Wrong Develop good computing habits Data and system configuration backup in the Windows ® operating system The W indo ws ® operating system offers some easy-to-use features for backing up your Windo ws ® settings and your data—docum ents and other important files.
189 If Something Goes Wrong Develop good computing habits Then, at a later time, you can re-establish your Windo ws ® configuration using the saved Restore Point. T o do this: 1 Click Start , All Programs , Acces sories , System T ools , and then System Restore .
190 If Something Goes Wrong Develop good computing habits Follo w these steps to back up y our computer or f iles to optical discs, or a storage driv e: Y ou cannot back up the computer while running on battery power . Connect the AC adaptor before continuing.
191 If Something Goes Wrong Develop good computing habits ❖ Hav e your factory Restore/Reconfiguration CD(s) on hand in case you need any f iles from them (av ailable on certain models).
192 If Something Goes Wrong If you need further assistance ❖ T urn OFF the computer while e xternal de vices are connected. ❖ Connect external de vices afte r turning OFF the computer . If this function cannot be used, change the settin g to Disabled.
193 If Something Goes Wrong If you need further assistance ❖ If the problem occurs while you are running a program, consult the program’ s documentation fo r troubleshooting suggestio ns. Contact the software company’ s technical support group for their assistance.
194 If Something Goes Wrong Other T oshiba Internet W eb sites Other T oshiba Internet Web sites T oshiba’ s worldwide offices toshiba.com W orldwide T oshiba corporate site computers.toshiba. com Marketing and product information in the USA accessories.
195 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additio nal T osh iba worldwide locations, please visit: www .toshiba.
196 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards prov ide a quick way to modif y selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot K ey Cards and Application Cards.
197 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off.
198 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 138 .
199 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Card s: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stack ed” card on the far right of the display .
200 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards.
201 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer .
202 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window .
203 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep m ode” on page 84 .
204 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 82 .
205 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i s pl a y o p t i o ns (only the .
206 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode.
207 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module.
208 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T ouchPad. For more information on using the T ou chPad, see “Disabling or enabling the T ouchPad™” on page 70 .
209 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution.
210 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot key tu rns the T OSHIB A Zo o mi n g Utility to zoom-out.
211 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our co mputer ships w ith the correct po wer su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world.
212 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide.
Glossary 213 DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M digital versatile (or video) disc read-only memory ECP enhanc.
214 Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SSD Solid State Driv e SVGA super video graphics adapter TFT thin film transistor USB univ ersal serial b us URL uniform resource lo cator WA N wide area netw ork www W orld Wide W eb Te r m s The following terms may appear in this user’ s guide.
Glossary 215 baud rate — The speed at which a comm unication de vice, such as a printer or mo dem, transmits in formation. Baud rate is the numb er of signal changes per second (not necessarily the same as bits per second). See also bits per second .
216 Glossary central processing unit (CPU) — The chip that functions as the “brain” of the computer . It takes informa tion from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information.
Glossary 217 D default — The setting selected by a program when the user does not specify an alternati ve setting. device — A component attached to the computer . Devices may be external (outside the computer’ s case) or internal (inside the computer’ s case).
218 Glossary double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device. In the W indows ® operating system, this refers to the pointing device’ s left button, unless otherwise stated.
Glossary 219 F fil e — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — The section of a s t o r a g e d r i ve that keeps track of the location of stored files.
220 Glossary Hibernation — A feature of many T oshiba computers that sav es to the internal storage driv e the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned of f.
Glossary 221 liquid crystal disp lay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it.
222 Glossary N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail.
Glossary 223 Plug and Play — Generally , refers to the com puter’ s ability to automatically configure itsel f to work with peripheral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device.
224 Glossary RJ11 — A modular connector used o n most U.S. telephone systems and direct-connect modems. The RJ11 co nnector is a 6-wire connector . R OM (read-only memory) — Non-v olatile memory that can be read but not written to. Non-volatile here means that information in ROM remains whether or not the computer is recei ving power .
Glossary 225 T TFT display — See active-ma trix display . U universal serial bus (USB) — USB is a serial b us that supports a data transfer rate of up to 4 80 Mbps (480 million bi ts per second). USB can connect up to 127 peripheral de vices through a single all- purpose USB port.
226 Index A A C adaptor 46 AC p o w e r connecting adaptor 47 accessories memory 51 adding memory 51 Alt keys 92 Application Cards 198 audio fil e s 131 audio features 131 B backing up files 91 batter.
227 Index moving 88 non-system disk or disk error message 167 not accessing disk driv es 166 running on battery power 106 setting up 43 , 53 warning resume failure messag e 166 computer lock 88 comput.
228 Index external display , adj usting 75 F F A T (File Allocation T able) 177 file e xtensions 97 file, backing up 91 fil e s backing up 98 printing 97 restoring 99 saving 96 fi ngerprint authentica.
229 Index using 92 keyboard, e xternal 75 L lock computer , using 88 M main battery removing 116 memory adding 51 problem solving 172 remo ving memory modul e slot cov er 54 memory module inserting 55.
230 Index printer connecting 75 problem solving 182 printing a file 97 problem solving AC p o w e r 173 accessing disk dri ves 166 battery charge does not last 174 battery not charging 173 cannot inse.
231 Index adding memory 51 computer 43 , 53 work en vironment 40 setting up a connection 127 Sleep mode 79 hot key 203 starting again from 87 solid state dri ve (SSD) 101 sound problem solving 179 sou.
An important point after buying a device Toshiba X300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba X300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba X300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba X300 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba X300 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba X300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba X300.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba X300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba X300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
