Instruction/ maintenance manual of the product U500-ST5307 Toshiba
Go to page of 251
GMAD00208010 08/09 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 182 in this gui de.
2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical ap.
4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n.
5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can.
6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer .
7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.
8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health W ireless LAN products, like other radio de vices, emit radio frequency electromagnetic energy . The lev el of energy emitted by W i reless LAN devices howe ver is f ar much less than the elect romagnetic energy emitted by wireless devices lik e for example mobile phones.
9 5.375 x 8.375 ver 2.3 Canada – Indust ry Canada (IC) This device complies with RS S 210 of Industry Canada. The installer of this radio equipment mu st ensure that the antenna is located or pointe.
10 5.375 x 8.375 ver 2.3 EU Declaration of Conformity TOSHIB A declares that this product conforms to the follo wing Standards: This product is carrying the CE-Mark in accordance w ith the related European Directiv es. The party responsib le for CE-Marking is TOSHIB A Europe GmbH, Hammfelddamm 8, 41460 Neuss, Ger many .
11 5.375 x 8.375 ver 2.3 VCCI Class B Information Modem W arning Notice Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN).
12 5.375 x 8.375 ver 2.3 Using this Equipment in Japan In Japan, the frequency bandwi dth of 2,400 MHz to 2,483.5 MHz for second generation low-po wer data communicatio n systems such as this equipment ov erlaps that of mobile object identifi cation systems (premises radio station and specified lo w-power radio station).
13 5.375 x 8.375 ver 2.3 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.5 MHz. 3. TOSHIB A Direct PC Monday – Friday: 10:00 – 17:0 0 T oll Free T el: 0120-15-1048 Direct Dial.
14 5.375 x 8.375 ver 2.3 Andorra Argen tina CNC: 533AN_HMW : “CNC C-6367” 533AN_MMW : “CNC C-6366” 512AN_HMW : “CNC C-6373” 512AN_MMW : “CNC C-6374” Australia Austria Azerbaijan Bahrai.
15 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Atheros ® Wireless Wi-Fi ® Link AR5B95 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
16 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Portugal Puerto Rico Qatar Romania Russia Saudi Arabia Senegal Serbia Singapore Slov ak R.
17 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply .
18 5.375 x 8.375 ver 2.3 radar system in the area. The presence of nearby radar operation may result in temporary interruption of operation of this device. The Access Point’ s radar detection feature will automatically restart operation on a channel free of radar .
19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8191SE This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
22 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
23 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that.
24 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table.
25 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization.
26 5.375 x 8.375 ver 2.3 The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations.
27 5.375 x 8.375 ver 2.3 Copyright This guide is copyrighted by T oshiba Amer ica Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced i n any form without the prior written permission of T o shiba.
28 5.375 x 8.375 ver 2.3 T rademarks Satellite, ConfigFree, and eco utility ar e either registered trademarks or trademarks of T oshiba Am erica Information Systems, Inc. and/or T oshiba Corporation. Adobe and Photoshop are either registered trademarks or tr ademarks of Adobe Systems Incorporated in the Unite d States and/or other countries.
29 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 37 This guide ...............................................................39 Safety icons ............................
30 Contents 5.375 x 8.375 v er 2.3 Turning on the power .......................................50 Setting up your software ...................................51 Registering your computer with Toshiba ................51 Adding optional external devices.
31 Contents 5.375 x 8.375 v er 2.3 Using and configuring Sleep mode ...................91 Closing the display panel ..................................94 Customizing your co mputer’s settings ....................94 Caring for your computer ..........
32 Contents 5.375 x 8.375 v er 2.3 Playing optical media ......................................113 Recording optical media .................................113 Removing a disc with the computer on (tray-type drive) ....................................
33 Contents 5.375 x 8.375 v er 2.3 Chapter 4: Exploring Y our Co mputer’ s Features ................... 134 Exploring the desktop ........................................... 134 Finding your way around the desktop .............135 Setting up for communications .
34 Contents 5.375 x 8.375 v er 2.3 Using a supervisor password ..........................157 Using a user password ...................................158 Deleting a user password ................................159 TOSHIBA Face Recognition Utility ...
35 Contents 5.375 x 8.375 v er 2.3 Chapter 6: If Something Goes Wrong ............. ...................... 182 Problems that are easy to fix ................................182 Problems when you turn on the computer ............183 The Windows ® operating system is not working .
36 Contents 5.375 x 8.375 v er 2.3 Appendix A: Hot Keys/TOSHI BA Cards .......... ........................ 213 Hot Key Cards .......................................................213 Using the Hot K ey Cards .................................214 Application Cards .
37 5.375 x 8.375 ver 2.3 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our co mputer model may be ENERGY ST AR ® qualified.
38 Introd uctio n 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would sav e more than $1.
39 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated.
40 Introd uctio n Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data.
41 Introduction Other documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are de signed to accommodate all possible configurations for an entire product Series.
42 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information.
43 Getting Started Selecting a place to work T o keep your computer in prime operating condition, protect you r work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
44 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin.
45 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer .
46 Getting Started Connecting to a power so ur ce Please handle your computer carefully to avo id scratching or damaging the surface. Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery .
47 Getting Started Connecting to a po wer sour ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to t.
48 Getting Started Char ging the main battery The computer’ s main battery light gives you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng ch.
49 Getting Started Using the computer for the f irst time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and be gin using it.
50 Getting Started Using the computer for the fir st time Small bright dots ma y appear on your screen displa y when you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology .
51 Getting Started Re gistering your computer with T oshib a Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely . The names of windows dis played, and the order in whi ch windows appear , may va ry acco rding to your software setup c hoices.
52 Getting Started Adding memory (optional) Adding memory (optional) HINT : T o purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com . Y o u r c o m pu t e r comes with enough memory to run most of today’ s popular applications.
53 Getting Started Adding memory (optional) The computer has two memory slots—Slot A and Slot B. Y ou can install one or two memory modules. Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Sleep or Hibernation mode, data will be lost.
54 Getting Started Adding memory (optional) 5 Remove the main battery . For information on removing the main battery , see “Removing the battery from the computer” on page 127 .
55 Getting Started Adding memory (optional) 7 Remove the memory module slot cover . 8 Place the scre ws and the co ver in a safe plac e so that you can retriev e them later . Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.
56 Getting Started Adding memory (optional) 11 Pick up the memory module by its sides, av oiding any contact with its connector . Position the modul e tow ard the socket, aligning the connector ’ s notch wi th the matching key in the socket.
57 Getting Started Adding memory (optional) cutouts in the side of the module. If the latches and cutouts do not line up correctly , repeat steps 12 - 13 . (Sample Illustration) Pr essing down on the memory module Do not force the memory module into posit ion.
58 Getting Started Adding memory (optional) 16 T urn the computer right side up. Make sure to remov e the soft cloth from the work surface be fore restarting the computer .
59 Getting Started Adding memory (optional) Removing a memor y module If you need to remov e a memory modul e: 1 Complete steps 1 – 8 in “Installing a memory modu le” on page 52 to shut down the computer an d open the memo ry module slot cov er .
60 Getting Started Adding memory (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screws.
61 Getting Started Adding memory (optional) 7 Reconnect the cables. 8 Restart the computer . TECHNICAL NOTE: Y ou must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory mo d u l e , you can check that the computer has recognized the change.
62 Getting Started Recovering the Internal Stor age Drive Recovering the Internal Storage Drive Y our computer includes recovery utilities to allo w you to recover your internal storage dri ve if necessary .
63 Getting Started Recovering the Internal Stora ge Drive ❖ During the internal storage drive recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor . ❖ It is strongly recommended that you create recov er y DVDs/media before using your system for the first time.
64 Getting Started Recovering the Internal Stor age Drive 4 A warning screen appears, statin g that when the reco very is ex ecuted all data will be deleted and rewritten.
65 Getting Started Recovering the Internal Stora ge Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover to out-of-box state . (Sample Image) Reco very of F a ctory Defa ult Software scr een 7 Click Next . A confirmation message displays reminding you that all data will be lost during the recov ery process.
66 Getting Started Recovering the Internal Stor age Drive The “Recov er to a custom size pa rtition” option restores you r C: dri ve to its out-of-box state, and allows you to specify the size for the C: partition.
67 Getting Started Recovering the Internal Stora ge Drive 5 When the T oshiba Recov ery W i zard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
68 Getting Started Recovering the Internal Stor age Drive 9 Click Next to be gin the recov ery . When the process is complete, a message displays indicating that the C: dri ve has been recov ered. 10 Press any k ey on the keyboard to restart the computer .
69 Getting Started Recovering the Internal Stora ge Drive 4 A warning screen appears stati ng that when the recov ery is ex ecuted all data will be deleted and rewritten.
70 Getting Started Recovering the Internal Stor age Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover without changing the hard drive partitions . (Sample Image) Reco very of F a ctory Default Software scr een 7 Click Next .
71 Getting Started Recovering the Internal Stora ge Drive T o create recov ery D VDs/media: 1 Click Start , All Programs , My T oshiba , and th en Recovery Media Creator .
72 Getting Started Recovering the Internal Stor age Drive ❖ Recov er without changing the in ternal storage driv e partitions For more information on these options, see “Recovering the Internal Storage Dri ve” on page 62 .
73 Getting Started Erasing the Internal Storag e Drive Erasing the Internal Storage Drive Erasing the internal storage drive will delete all data on the drive, including the partitions. Be sure to create recovery DVDs/media and back up your data to external media before erasing the internal storage drive.
74 Getting Started Checking the inte rnal stor age drive operating status purposes. This process may take se veral hours, depending on the size of your internal storage dri ve. (Sample Image) Er ase the har d disk scr een 4 Click Next . A confirmation message displays reminding you that all data on the internal storage driv e will be lost.
75 Getting Started Using the T ouchP ad™ Installing drivers and applications The T osh iba Application Installer allows you to reinstall the drivers and applications that were original ly bundled with your computer . T o reinstall driv ers and applications: 1 Click Start , All Pr ograms , My T oshiba , and then TO S H IBA Application Installer .
76 Getting Started Using the T ouchP ad™ Refer to the table belo w for speci fic instructions on performing each operation. The pointer is the icon (usually an arrow) that moves on the screen when you slide your finger across the T ouchPad or move a mouse connected to your computer .
77 Getting Started Using the T ouchP ad™ Scroll vertically Slide your finger along the right edge of the T ouchPad in the direction you want to scroll.
78 Getting Started Using the T ouchP ad™ Adjusting T ouchPad™ settings While you are typing, the on-screen pointer may seem to move or jump around “by itself” to ran dom locations on the screen. The on-screen pointer may also seem to automatically select text, click buttons, and activ ate other user interface elements.
79 Getting Started Using external display de vices T ouchPad setting options vary by computer model. The T ouchPad settings are accessible through the Mou se Properties option of the Windows Control Panel. For more information, please visit www .support.
80 Getting Started Using external display de vices Connecting the display device If you are connecting a television or other video display device to the computer’ s HDM I™ Out port, refer to “Connecting an HDMI™-compatible television or VCR/D VD player” on page 80 .
81 Getting Started Using external display de vices For more detailed HDMI-C EC information visi t pcsupport.toshiba.com . Connecting an external monitor or projector Y ou can easily attach an external monitor or projector to your computer if you need a lar ger screen.
82 Getting Started Using an e xternal ke yboar d ❖ Built-in display and TV (or other external video device) simultaneously ❖ Built-in display and external monitor (extended desktop) ❖ Built-in d.
83 Getting Started Connecting a printer Connecting a printer Y our printer documentation may require you to install the printer software before physically connecting the printe r to your computer . If you do not install the software as instructed by the printer manufacturer , the printer may not function correctly .
84 Getting Started T urning off the computer Setting up a printer Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play , follo w these steps to set it up for the first time.
85 Getting Started T urning off the computer Options for turning off the computer Depending on the operating sy stem installed, you have more than one option av ailable for turning off the computer: Shut down, Hibernate, and Sleep. Each option has its advantages.
86 Getting Started T urning off the computer For information on ho w to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 89 .
87 Getting Started T urning off the computer Using the Shut down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns of f your computer .
88 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click P ower b uttons and lid to display the actions that you can configure.
89 Getting Started T urning off the computer Restarting your computer T o start the computer up again, press the po wer b utton unti l the ON/OFF light glows white. If you turn off the computer by closing the display panel, you can start it again by open i ng the display panel .
90 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options screen 5 Select Hibernate for the options you want.
91 Getting Started T urning off the computer Starting again from Hibernation mode T o start up the computer from Hibernation mode, press the power button until the ON/OFF light gl o ws white.
92 Getting Started T urning off the computer T o use any of these methods, you f irst need to enable them using the Power Options feature. 1 Click Start , Contro l Panel , System and Security , and then Po wer Options . The Po wer Options window appears.
93 Getting Started T urning off the computer 4 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 5 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 6 Select Sleep for the options you want.
94 Getting Started Customizing your comp uter’ s settings Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the ON/OF F light glows white.
95 Getting Started Caring for your computer Moving the computer Before moving your computer, e ven across the room, make sure all dri ve acti vity has ended (the internal storage drive and optical dri v e indicator lights stop glowing) and al l external peripheral cables are disconnected.
96 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive.
97 Learning the Basics Using the ke yboar d ❖ Back up your files to ex ternal media on a regular basis. Label the backup copies clearly and store them in a safe place.
98 Learning the Basics Using the ke yboar d Character keys T y ping with the character keys is very much like typing on a typewriter , e xcept that: ❖ The space bar creates a space char acter instead of just passing ov er an area of the page. ❖ The lo wercase letter l (el) and the number 1 are not interchangeable.
99 Learning the Basics Using the ke yboar d Function keys The function k eys (not t o be confused with the Fn key) are the 12 keys at the top of the k eyboard. (Sample Illustration) Function ke ys F1 through F12 are called function keys because the y ex ecute programmed functions when pressed.
100 Learning the Basics Using the ke yboar d Overlay keys The ke ys with gray numbers and symbols on the front of them form the numeric and cursor ov erlay . This overlay lets you enter numeric data or control the cursor as you would using the 10-key ke ypad on a desktop comput er’ s k eyboard .
101 Learning the Basics Starting a pr og ram Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. T o find the file, use the Start menu or W indo ws ® Explorer .
102 Learning the Basics Starting a pr ogram Starting a program from Windows ® Explorer If a program is not listed in th e All Programs menu, yo u can start it from W indows ® E xplorer . W indo ws ® Explorer gi ves you a view of your computer’ s contents as a hi erarchy or “tree.
103 Learning the Basics Saving your work Starting a program using the Search programs and files field This example uses the Start menu’ s Search programs and f iles field to start W ordPad: 1 Click Start to display the Start menu. The Search programs and files f ield appears at the bottom of the Start menu.
104 Learning the Basics Saving your work Saving files 1 Click on the arrow in the upper -left corner of your W indows ® -based application to display the drop-down menu, and then click Sav e . If you are working with a docum ent that already has a f ile name, this i s all you need to do.
105 Learning the Basics Printing your work File names The W indo ws ® operating system supp orts long file names that can contain up to 260 characters and can include spaces. Some applications do not support long file names and require file names limited to no more th an eight characters.
106 Learning the Basics Backing up your work 2 Click on the arrow in the upper -left corner of your W indows ® -based application to display th e drop-down menu, and then click Print . The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters.
107 Learning the Basics Using the optical drive Restoring your work T o restore information from your backu p media to your internal storage driv e, use the Restore option in the Windo ws ® Backup and Restore program. Look in the online Help or your op erating system documentation for informati on on restoring files.
108 Learning the Basics Using the optical drive For optimum DVD performance, it is recommended that you play DVDs while running the computer on AC power . When viewing DVD movies use the DVD Player software that came with your computer . Optical drive components The optical dri ve is located on th e side of the computer .
109 Learning the Basics Using the optical drive Manual eject hole (a vailable on certain models) —Use if you need to release the disc tray when the power is off. Use a straightened paper clip or o ther na rro w object to press the manual eject button located inside the hole.
110 Learning the Basics Using the optical drive Inserting an optical disc (slot-type drive) (A vailable on certain models) T o insert an optical disc into the dri ve: 1 Hold the disc by its edges and check that it is clean and free of dust. Handle DVDs and CDs carefully , making contact only with the center hole and edge.
111 Learning the Basics Using the optical drive Removing a disc (slot-type drive) Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing. Doing so could damage the dis k or the drive. The computer must be powered on to eject a disc.
112 Learning the Basics Using the optical drive 6 Place the disc carefully in th e disc tray , label side up. (Sample Illustration) P ositioning the disc in the drive 7 Gently press the disc onto the center spindle until it clicks into place. Handle DVDs and CDs carefully , making contact only with the center hole and edge.
113 Learning the Basics Using the optical drive Playing an audio CD Insert an audio CD and close the disc tray . If the computer is turned on, the default player opens. ❖ T o play the CD or to pause, click the Play/Pause button. ❖ T o stop the CD, click the Stop button.
114 Learning the Basics Using the optical drive Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your T .
115 Learning the Basics T oshiba’ s online r esour ces Removing a disc with the co mputer off (tray-type drive) T o remov e a disc with the computer turned of f: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole.
116 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your com puter while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process.
117 Mobile Computing Running the computer on battery power Running the computer on battery power The computer contains a remov abl e Lithium-Ion (Li-Ion) battery that provides po wer when you are aw ay from an A C outlet. Y ou can recharg e it many ti mes.
118 Mobile Computing Char gi ng batteries TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on. Power management Y our computer ships with t he pow.
119 Mobile Computing Char ging ba tteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet.
120 Mobile Computing Monitoring main battery power T o recharge the R TC battery , plug the computer into a li v e electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC battery because it charges while the computer is on.
121 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ), the ON/OFF light ( ), and the powe r button light (near the upper -left corner of the keyboard).
122 Mobile Computing Monitoring main battery power Determining remaining battery power Wait at least 16 se conds after turning on the computer before trying to monitor the remaining battery power . The computer needs this time to check the battery’ s remaining capac ity and perform its calculations.
123 Mobile Computing Monitoring main battery power Setting batter y notifications Y ou can set two notifi cations. Each notification can be set to alert you when a specified percentage of remaining battery po wer has been reached.
124 Mobile Computing Monitoring main battery power ❖ Ho w much you use the internal storage driv e, optical dri ve, diskette dri ves, or other optional de vices ❖ Where you are working, since oper.
125 Mobile Computing Monitoring main battery power 2 Select an appropriate plan for your work en vironment or create your own custom plan. 3 Click Create a po wer plan in the left pane to set up a new plan. T o edit a plan or to edit advanced settings, continue to the following steps.
126 Mobile Computing Using the T OSHIB A eco power plan 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: eco and Balanced. 3 Release the Fn key . The hot ke y card disappears. Y ou are now in the selected mode.
127 Mobile Computing Changing the main battery Changing the main batter y When your main battery has ru n out of power , you have two options: plug in the A C adaptor or install a char ged main battery .
128 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease lock 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer .
129 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks.
130 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 127 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life.
131 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
132 Mobile Computing Disposing of used b atteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you hav e fully rech arged the battery .
133 Mobile Computing T raveling tips T o shiba is dedicated to preservi ng the en vironment by sponsoring Call2Recycle™ , a program of the Rechar geable Battery Recycling Cor por ati on. For more information and for drop-of f locations, visit www .rbrc.
134 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system.
135 Exploring Y our Computer’ s Features Exploring the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, taskbar , notification area, and background pattern.
136 Exploring Y our Computer’ s Features Explorin g the desktop Y our desktop may contain othe r icons depending on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it.
137 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines wit.
138 Exploring Y our Computer’ s Features Setting up for communications Connecting your computer to a network Y ou can connect your computer to a network to increase its capabilities and functionali ty using one of its communication ports.
139 Exploring Y our Computer’ s Features Setting up for communications ❖ Communicate with your of fice’ s local area network (LAN) or larger corporate wide area netw ork (W AN) For specif ic information about connecting to a LAN or W AN, consult your network administrator .
140 Exploring Y our Computer’ s Features An overview of using the Internet Now you are ready to send a fax or use the modem to connect to an online service or the Internet.
141 Exploring Y our Computer’ s Features An overview of using the Internet Connecting to the Internet T o connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A W eb browser ❖ An Internet Service Provider (ISP) account Once you hav e established an ISP account, you can connect to the Internet.
142 Exploring Y our Computer’ s Features An overview of using the Internet ❖ Internet chat roo ms A chat room is a W eb site that offers a place whe re people with similar interests and ideas comm unicate in real-time, one-on- one or in groups, by typing messages which are instantly viewed by others on their computer screens.
143 Exploring Y our Computer’ s Features Explorin g audio featur es Exploring audio features Y ou can use your computer to record sounds using the com puter’ s internal microphone (av ailable on certain models) or an opti onal external microphone.
144 Exploring Y our Computer’ s Features Using the W eb Camera TECHNICAL NOTE: When using amplified speakers, use speakers that require an external power source.
145 Exploring Y our Computer’ s Features Using an ExpressCar d ® Using an ExpressCard ® The ExpressCard ® slot supports the use of Ex pressCard media. The slot also supports ho t swapping, which allo ws you to replace one ExpressCard with another while the computer is on.
146 Exploring Y our Computer’ s Features Using the Memory Car d Reader 4 Grasp the ExpressCard an d pull it straig ht out. (Sample Illustration) Removing an Expr essCar d Using the Memory Card Reade.
147 Exploring Y our Computer’ s Features Using the Memory Car d Reader Inserting memory media The follo wing instructions apply to all types of supported media devices. 1 T urn the media so that the cont acts (metal areas ) are face do wn. 2 Push the media into the ad apter until it locks in place.
148 Exploring Y our Computer’ s Features Using the eSA T A/USB combo port Do not remove memory media while data is being written or read. Even when the Windows ® message “copying...” disappears, writing to the media might still be in progress and your data could be destroyed.
149 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help yo u to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns.
150 Utilities TOSHIB A Assist ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ TOSHIB A Accessibility ❖ Fingerprint Authentication Utilit y ❖ TOSHIB A eco Utility™ ❖ TOSHIB A Ser.
151 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings (Sample Image) T OSHIBA Assist window – Connect ta.
152 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secur e tab.
153 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility ❖ TOSHIB A HDD Protection Utility (Sample Image) T OSHIBA Assis.
154 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Se tup (Hardware Settings) ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Butto.
155 Utilities TOSHIB A Applicati on Installer TOSHIBA Application Installer The TOSHIB A Application Installer allows you to reinstall the dri vers and applications that were originally bundled with your computer . T o reinstall driv ers and applications: 1 Click Start , All Pr ograms , My T oshiba , and then TO SH I BA Application Installer .
156 Utilities Setting passwor ds Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again.
157 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to se.
158 Utilities Setting passwor ds 6 Click OK . The supervisor password u tility dialog bo x appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK .
159 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , TOSH IBA , Utilities , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab .
160 Utilities TOSHIB A F ace Recognition Utility TOSHIBA Face Recognition Utility Y our computer may come with the TOSHIB A Face Recognition utility . This utility provides another way to log on to y our computer . For high security purposes, TOSHIBA Face Recognition is not a suitable substitute for Windows ® passwords.
161 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have.
162 Utilities TOSHIB A HDD Pr otection Utility TOSHIBA HDD Protection Utility The TOSHIB A HDD Protection Utility controls your compu ter’ s hard disk dri ve (HDD) protection feature, which parks the HDD whene ver motion is detected on the computer .
163 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contro l Panel , Hardware and Sound , and then under Devices and Printers , click Mouse , or click the Mouse icon in the Op timize tab of TOSHIB A Assist .
164 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshib a configuration management tool av ailable through th e W indows ® operating system.
165 Utilities T O S H I BA H a rd w a re S e t u p ❖ Button Sett ing —Lets you set the conditions for th e po wer button and/or the other buttons. (Sample Image) TOSHIB A HWSetup screen - Button S.
166 Utilities TO S H I B A H a rd w a re S e t u p ❖ Ke y b oa rd —All ows you to access the w ake-on keyboard function ❖ LAN —Allows you to set networking functions ❖ Illumination— Allows.
167 Utilities USB Sleep and Char ge Utility USB Sleep and Charge Utility This utility displays w hether the “USB Sleep and Charge function” is enabled or disabled and shows the position of the USB port that supports the “USB Sleep and Charge function.
168 Utilities USB Sleep and Char ge Utility ❖ When “USB Sleep and Charge function” is set to Enabled, USB bus power (DC 5V) will be supplied to the compatible port even when the power of the computer is turned OFF . USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports.
169 Utilities USB Sleep and Char ge Utility Enabling USB Sleep and Charge This utility can b e used to enable or disable the “USB Sleep and Charge function” group . Check the check box fo r the group to enable the “USB Sleep and Charge function” for the USB port assigned to that group.
170 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 227 ).
171 Utilities TOSHIB A Button Support TOSHIBA Button Support TOSHIB A Button Support allows you to customize the Mute and Media buttons . These buttons ar e located on the system control panel directly above the keyboard. T o access TOSHIB A Button Support: 1 Click the TO SHIB A Button Support icon in the Optimize tab of TOSHIB A Assist .
172 Utilities TOSHIB A Accessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required.
173 Utilities F ing erprint Authent ication Utility Fingerprint Authentication Utility (A vailable on certain models) The fingerprint authentication utility (av ailable on certain models) can be used to replace the ke yboard-based user password authentication syst em when booti ng up.
174 Utilities F ing erprint Authenticati on Utility The Fast User Switching feature of the W indo ws ® operating sy stem is also supported. If user A is logged on and the fingerprint utilit y verif ies the fingerprint of user B (who is already enrolled), the utility recognizes the fingerprint and switches th e users.
175 Utilities F ing erprint Authent ication Utility Observe the follo wing to improve the f ingerprint recog nition success rate. ❖ Enroll two or more f ingers. ❖ Enroll additional fingers if r ecognition failure occurs often using enrolled fingers.
176 Utilities TOSHIB A eco Utility™ TOSHIBA eco Utility™ The T oshiba eco u tility™ monitors y our power sa vings from using the eco po wer plan by tracking real-time po wer consumption and accumulated savings o ver time.
177 Utilities TOSHIB A Service Station TOSHIBA Service Station The TOSHIB A Service Station helps you keep your ne w computer running at its best by notifying you when updated software, firmw are, documentation or othe r information is av ailable for your computer .
178 Utilities ConfigF r ee® The TOSHIB A PC Health Mo nitor software does n ot extend or modify T oshiba's obligatio ns under its standard limited warranty in any way .
179 Utilities ConfigF r ee® ❖ Click the Conf igFree icon in the notification area, and then click the desired utility . If your computer is not connected to a network, the ConfigFree icon in the notification area is displayed with an “X.
180 Utilities ConfigF r ee® Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices. Y ou can switch network settings simply by selecting the profile with the desired settings.
181 Utilities ConfigF r ee® 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Create Prof ile W izard.
182 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself.
183 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask .
184 If Something Goes Wrong Pr oblems when you turn on the computer V erify that the computer is on by looking at the ON/OFF indicator . If the indicator is glowing, the computer is on.
185 If Something Goes Wrong Pr oblems when you turn on the computer T o charge the battery , leave the computer plugged into a liv e wall outlet for sev eral hours. For more information see “Charging batteries” on page 118 . The computer displays the Non-System disk or disk error message.
186 If Something Goes Wrong The W indo ws ® operating system is not working 5 V erify that the A C adaptor is th e correct unit for your computer model.
187 If Something Goes Wrong The W indo ws ® operating system is not working Using Startup options to fix problems If the operating system fails to start properly , you may ha ve to change your system’ s configuratio n or verify the startup procedure to fix the problem.
188 If Something Goes Wrong The W indo ws ® operating system is not working Internet problems My Internet connection is v ery slow . Many f actors contribute to the speed with which you can surf the Internet.
189 If Something Goes Wrong F ixing a pr oblem with Device Manag er Fixing a problem with Device Manager Device Manager pro vides a way to check and change the configuration of a de vice. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable.
190 If Something Goes Wrong Memory pr oblems Memory problems Incorrectly connected or faulty memory modu les may cause errors that seem to be hardware or ev en software related. It is worthwhile checking for these firs t: 1 Click Start , and then click the Shut do wn button in the lo wer-right corner of the Start menu.
191 If Something Goes Wrong P ower and the batteries The A C power light does not come on when y ou plug in the A C adaptor and power cord/cable. Make sure the A C adaptor and po wer cord/cable are firmly plugged into both the wall outlet and the computer .
192 If Something Goes Wrong K e yboar d pr oblems site at accessories.toshiba.com. Refer to this site often to stay current on the most recent software and hardware options for your computer , and for other product information. For more information on maintaining battery power , see “Char ging batteries” on page 118 .
193 If Something Goes Wrong Display pr oblems HINT : Holding the Fn key and pressing the F5 key several times will advance you through the display options. If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’ s po wer cord/cable is f irmly plugged into a working p ower outlet.
194 If Something Goes Wrong Disk or storag e drive pr oblems The display mode is set to Simultaneous and the exter nal display de vice does not work. Make sure the e xternal monito r is capable of displaying at resolutions of 800 x 600 or higher .
195 If Something Goes Wrong Disk or storag e drive pr oblems This feature is not available for optical drives. 4 Click the T ools tab. 5 Click the Check now ... button. The Check Disk box appears. 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system er rors ❖ Scan for and attempt reco very of bad sectors 7 Click Start .
196 If Something Goes Wrong Optical drive pr oblems (tra y-type drive) The drive cannot r ead a diskette. T ry another diskette. If you can access the second diskette, the first diskette (not the drive) is probably causi ng the problem.
197 If Something Goes Wrong Sound system pr oblems If the problem is with an optical dat a disc, refer to the software’ s documentation and check that the hardware configuration meets the program’ s needs. The disc will not come out of the driv e when y ou click the eject button on the scr een.
198 If Something Goes Wrong Expr essCar d ® pr oblems ExpressCard ® checklist ❖ Make sure the card is insert ed properly into the slot. ❖ Make sure all cables are securely connected. ❖ Occasionally a defecti ve ExpressCard ® slips through quality control.
199 If Something Goes Wrong Expr essCar d ® pr oblems ❖ If no resource conflict is indicated, contact the card manufacturer for additional troubleshooting assistance. 6 Click OK to conf irm the uninstal l. 7 In the Device Manager window , click the Action menu and select Scan for Hard ware changes .
200 If Something Goes Wrong Printer pr oblems Printer problems This sectio n lists some of t he most common pr inter problems . The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper .
201 If Something Goes Wrong W ireless networking pr oblems Check the communications paramete rs (baud rate, parity , data length and stop b its) specified in the communicatio ns program. It should be set up to transmit at 300, 1 200, 2400, 4 800, 9600, 1 4400, 28800, 33600 bps (bits per second) or higher .
202 If Something Goes Wrong W ireless networking pr oblems site, the ISP’ s (Internet Serv ice Provider) service may be disrupted. ❖ V erify that the Service Set Id entifier (SSID), or netw ork name, is correct— i.e., that it matches the SSID assigned to the access point you are attempting to connect through.
203 If Something Goes Wrong D VD operating pr oblems The Windo ws ® operating system wir eless management utility does not work. If you are using an external W i-Fi ® adapter (an ExpressCard ® , USB adapter , or other variety), check if the adapter comes with its o wn management utility .
204 If Something Goes Wrong Develop good computing habits 4 Click Sav e changes . The screen sa ver runs while y ou ar e watching a movie or title. If the screen sav er is enabled, it runs on top of any movie or title you are watching. T o disable the screen sa ver: 1 Right-click on the desktop and click Personalize in the menu.
205 If Something Goes Wrong Develop good computing habits Get familiar with all the user’ s gu ides provided with your co mputer , as well as the manuals that come with the programs and de vices you purchase. Y our local com puter store or book store sells a v ariety of self-help books you can use to supplement the information in the manuals.
206 If Something Goes Wrong Develop good computing habits displays a message that the resto re point was successfully created. 5 Click Close . Then, at a later time, you can re-establish your Windo ws ® configuration using the sa ved restore point.
207 If Something Goes Wrong Develop good computing habits from optical discs. External opti cal disc writers are also w idely av ailable. Follo w these steps to back up y our computer or files to optical discs, or a storage driv e: Y ou cannot back up the computer while running on battery power .
208 If Something Goes Wrong Develop good computing habits successfully . Always carefully follo w the installation instructions that accompany the hardware or software.
209 If Something Goes Wrong If you need further assistance The “USB W akeup function” does not work. ❖ When the “USB Sleep and Charge function” is set to Enabled the “USB W akeup function” does not work for ports that support the “USB Sleep and Charge function .
210 If Something Goes Wrong If you need further assistance For the detailed s pecificati ons for your computer , visit pcsupport.toshiba.com . C lick Produ ct Support , search for your model, and then click Detailed Specs .
211 If Something Goes Wrong Other T oshiba Internet W eb sites Other T oshiba Internet Web sites T oshiba’ s worldwide offices toshiba.com W orldwide T oshiba corporate site laptops.toshiba.com Marketing and product information in the USA accessories.
212 If Something Goes Wrong T oshiba’ s worldwide off ices For more information on additio nal T osh iba worldwide locations, please visit: www .t oshiba.
213 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards provi de a quick way to modify selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot Ke y Cards and Application Cards.
214 Hot Keys/TOSHIBA Cards Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off.
215 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 150 . TOSHIB A HDD Protection utility For more information, refer to “TOSHIB A HDD Protection Utility” on page 16 2 .
216 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Not all functions are supported on all models. Using the Application Cards T o launch an application using the Applicati on Cards: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen.
217 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Card Case The Card Case feature allows you to choose which cards appear in the Application Car d display (see “Using the Applicati on Cards” on page 216 ). T o use the Card Case: 1 Click Start , All Programs , TOSH IBA , Utilities , and then Settings for Flash Cards .
218 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Volume Mute or Fn + This TOSHIB A Card or hot ke y enables/disables volume mute on your computer .
219 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer .
220 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window .
221 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep m ode” on page 91 .
222 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 89 .
223 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i sp l a y o p t io n s (only the .
224 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode.
225 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module.
226 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad. For more information on using the T ou chPad, see “Using the T o uchPad™” on page 75 .
227 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution.
228 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot key turns the curs or control ov erlay on and o ff. Fn + This hot key turns the numeric overlay on and of f. Fn + This hot key turns the scroll lock feature on and off.
229 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer ships w ith the correct power su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world.
230 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide.
Glossary 231 DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M dig ital versatile (or video) disc read-only memory ECP enhan.
232 Glossary RFI radio frequency interference RO M read-only memory RT C real-time clock SCSI small computer system interface SD Secure Digital SDRAM synchronous dynamic ran dom access memory SRAM sta.
Glossary 233 application — A computer program that yo u use to perform tasks of a specific type. Applications includ e wo rd processors, spreadsheets, and database management systems. See also pro gram . B backup — A copy of a file, usually on a remov able disk, kept in case the original file is lost or damaged.
234 Glossary CD — An individual compact disc. See also CD-R OM. CD-R OM (compact disc r ead-only memory) — A form of high- capacity storage that uses laser opt ics instead of magnetic means for reading data. See also CD . Compare DV D - RO M . central processing unit (CPU) — The chip that functions as the “brain” of the computer .
Glossary 235 cursor — An on-screen symbol (usually a flas hing verti cal line) that indicates the position where charact ers will appear when you enter data. D default — The setting selected by a program when the user does not specify an alternati ve setting.
236 Glossary document — Any file created with an application and, if sa ved to disk, gi ven a name by which it can be retrie ved. See also fil e . double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device.
Glossary 237 F fil e — A collect ion of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — The section of a s t o r a g e d r ive that keeps track of the location of stored files.
238 Glossary Hibern ation — A feature of many T oshiba computers that saves to the i n t e r n a l s t o r a g e d r iv e the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned of f.
Glossary 239 liquid crystal disp lay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it.
240 Glossary N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail.
Glossary 241 Plug and Play — Generally , refers to the com puter’ s ability to automatically configure itsel f to work with peripheral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device.
242 Glossary res ta r t — Synonymous with reboot. T o reset the computer by reloading the operating system without tu rn ing the computer off. See also boot . RJ11 — A modular connector used o n most U.S. telephone syst ems and direct-connect modems.
Glossary 243 system prompt — The symbol (in the MS-DOS ® operating system, generally a drive letter followed b y a “greater than” sign) indicating where users are to enter commands.
244 Index A A C adaptor 46 A C po wer (DC-IN) connecting adaptor 47 A C power light 46 Alt keys 98 Application Cards 215 audio fil e s 143 audio features 143 B backing up files 97 battery Call2Recycle.
245 Index charging the battery 48 checking device properties 189 communications network connection 138 set up 137 compact discs handling 110 inserting 110 compact discs (slot-type driv e) removing 111.
246 Index non-system disk or disk error 185 problem with display settings/ current settings not wor king with hardware 193 warning resume failure 184 Error-checking 194 eSA T A connecting to the eSA T.
247 Index ExpressCards® 145 installation memory module 52 installing main battery 127 , 129 memory modules 52 mouse 82 Internet bookmarked site not found 188 connecting to 141 features 141 slow conne.
248 Index wireless 137 notification area 136 O optical disc handling 112 inserting (slot-type driv e) 110 inserting (tray-type drive) 111 positioning 112 optical driv e driv e in-use indicator light 1.
249 Index fault y memory 190 high-pitched noise 19 7 Internet bookmarked site n ot found 188 Internet connection is slo w 188 keyboard not responding 184 keyboard produces unexpected characters 192 mi.
250 Index speakers using external 143 start button 136 starting a program 101 Search programs and f iles field 103 W indo ws® Explorer 102 W indows® Start menu 101 starting up the computer from Shut.
251 Index W war ran ty standard limited warranty 41 We b 140 We b C a m e r a using 144 We b s i t e s 210 Wi - F i ® wireless netw orking 137 W indo ws® Explorer 102 W indows® operating system Hel.
An important point after buying a device Toshiba U500-ST5307 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba U500-ST5307 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba U500-ST5307 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba U500-ST5307 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba U500-ST5307 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba U500-ST5307, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba U500-ST5307.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba U500-ST5307. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba U500-ST5307 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
