Instruction/ maintenance manual of the product TCB-AX21UL Toshiba
Go to page of 16
REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE) Installation Manual Installation Manua l Remote controller for air conditioner (Split type) 1 English Manuel du propriet aire Télécommande pour cli.
Wireless remote controller kit Installation Manual –1– Contents 1 ACCESSORY PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT . . . . . . . . . . 3 3 INSTALLATION LOCATION OF SIGNAL RECEIVING UNIT .
Wireless remote controller kit Installation Manual –2– EN 1 ACCESSORY PARTS No. Parts Quantity 1 Signal receiving unit (provided 7.9” (200 mm) power cable) 1 2 Mounting bracket 1 3 Screws ∅ 0.16” x 1.0” (M4 x 25 mm) 2 4 Screws ∅ 0.16” x 1.
Wireless remote controller kit Installation Manual –3– 2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT 1 3 2 4 6 5 Screw Remove Face plate Remove the face plate from Signal receiving unit.
Wireless remote controller kit Installation Manual –4– EN 3 INSTALLATION LOCA TION OF SIGNAL RECEIVING UNIT • Do not install in a location where the air contains oil mist, such a s in a kitchen or factory. • Do not install next to a window, or in an y other location directly exposed to sunlight and outside air.
Wireless remote controller kit Installation Manual –5– 4 HOW TO INSTALL THE SIGNAL RECEIVING UNIT NOTE • To avoid malfunction of the re mote controlle r, do not assemble or run remote control wiring together w ith the power cabl es, an d do not enclo se them in the same metal conduit.
Wireless remote controller kit Installation Manual –6– EN 2. In order to later pass the Signal r eceiving unit wiring out through the upper case (thin part at the top center), use nippe rs or a similar tool to cut a notch in t he same size as the Signal receiving unit cord (optional).
Wireless remote controller kit Installation Manual –7– 4. Use bracket parts (A) and (B) t o securely grip the ceiling material. (Fig. E) 5. Connect the Signal receiving unit wire (2-core) to the wire from the indoor unit. (Refer to “Wiring the Signal receiving unit.
Wireless remote controller kit Installation Manual –8– EN 5 HOW TO PERFORM CABLING OF THE SIGNAL RECEIVING UNIT Flush Mounting Connection diagram Provided wire joint (WHT 2) 1. Strip the insulation to approximately 0.55” ( 14 mm) from the ends of the wires to be connected.
Wireless remote controller kit Installation Manual –9– 6 REQUIREMENT The control by two remote controll ers is enab led by in stalling the wireless remote contro ller with the wired remote controller for an indo or unit. (Max. 2 remote controllers of wireless or wired are insatiable.
Wireless remote controller kit Installation Manual –1 0– EN To operate a group control of mult iple indoor units by 2 remote controllers MAIN and SUB remote controll ers are operable even if they are installed to any indoor u nit.
Wireless remote controller kit Installation Manual –1 1– 8 HOW TO SET THE ADDRESS SWITCH • When the multiple Signal receiving units are in stalled in the same room, an address can be set to prevent cross communication.
Wireless remote controller kit Installation Manual –1 2– EN 10 SELF-DIAGNOSIS TA BLE AND MEASURES Lamp indication of Signal receiving unit 11 CAUTIONS FOR INSTALLATION OF THE REMOTE CONTROLLER • To operate the remote control ler by fixing it to the wall, etc.
Wireless remote controller kit Installation Manual –1 3– 12 EXPLANATION TO CUSTOMERS • Hand over the “Owner’s Manual” and “Insta lla tion Manuals” to the customer after installation works. • Explain usage and maintena nce of the remote controller according to “Owner’s Manual”.
Wireless remote controller kit Installation Manual –1 4– EN 14 TEST RUN Before test run • Before turning on the power supply switch, carry out the follo wing procedure. 1 Using 500V-megger, check 1M Ω or more exists between the terminal block 1 to 3 and the earth.
(EH99677601) 85464369216000 +00EH99677601_01EN_remo _IM.book Page 15 Thu rsday, October 8, 2009 4:12 PM.
An important point after buying a device Toshiba TCB-AX21UL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba TCB-AX21UL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba TCB-AX21UL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba TCB-AX21UL you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba TCB-AX21UL will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba TCB-AX21UL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba TCB-AX21UL.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba TCB-AX21UL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba TCB-AX21UL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
