Instruction/ maintenance manual of the product SD-R1312 Toshiba
Go to page of 16
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-R1312 CD-R W/D VD-R OM COMBO DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the Com bo Drive ...........................
1 INTR ODUCTION – SD-R1312 General Features Reads and record s digital data on CD-R/-RW discs at 32X/10X 3-way Disc Eject (ej ect button, software, emergency eject hole ) Average Random Access Time .
Front Panel Figure 1.SD-R1312 DVD Write able Drive Front Panel Loading Tray Load disc using tray. Busy Light LED The LED lights green or amber whe n the drive is operating (LED is amber whe n drive is writing.) Eject Button The Eject button is used to open the disc tra y so you can install or remove a disc.
3 SETUP – SD-R1312 The following steps must be performe d to properly install your drive: • Set Drive J umper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach P ow er Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pi n s located on the rear of the Combo drive.
4 Placing Combo Drive inside your Computer Now that you have set the jumpers, you are read y to install your Combo drive inside your computer. Important Note: Disconnect power fr om your co mputer system before b eginning installation. Remove computer co ver and faceplate if required.
5 Audio Cable (optional) - If you have a sound card and speakers, and would like t o play audio CDs on your computer, you will need to install a CD/DVD audio ca ble. Toshiba's Combo drives use a sta ndard 4-pin audio cable that can be purchased from mo st local computer suppliers.
6 USING THE D VD Combo Drive – SD-R1312 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
7 Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the Combo drive, perform the following steps: 1. Open the Loading T r a y by pressing the Eject Button. 2. Slide disc holders a wa y from disc. 3. Grasp disc by edges , and lift out of loading tra y .
8 Emergency Ejection CAUTION: The following procedure is intended on ly as a last resort when pressing the eject button fails to open the Loading Tray 1. T ur n computer powe r OFF by properly shutting down system. 2. Inser t a solid bar (i.e. large paper clip) into Emergency Eject hol e and push in until loading t ra y opens.
9 TR OUBLESHOO TING – SD-R1312 Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instructi ons to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
10 SPECIFICA TIONS – SD-R1312 General Interface: ATAPI Applicable Formats - Write: Formats for Writing Disc at once, Track at once , session at once, Packet Write, increm ental write, restri cted ov.
11 CD-R (Write) 5,940 – 6,800r pm (12/16/20/24/32X ZCL V) 5,100 – 5,940rpm (12/15/20/24X ZCL V) 2,550 – 5,940rpm (12X CL V) 850 – 1,980prm (4X CL V) High Speed CD-R W (Write) 2,125 – 4,950rp.
12 Relativ e Humidity Operating 8% to 80% Storage/Shipping 5% to 95% (wet bulb 40° C ma x) Vibration Operating (5 to 500 Hz) (re ad) 2.45 m/s 2 (0.25G) (O-P) Operating (5 to 500 Hz) (wr ite) 2.45 m/s 2 (0.25G) (O-P ) Non-operatin g (10 to 500Hz) 9.8 m/s 2 (1.
13 DRIVE CONNECT ORS – SD-R1312 Figure 1.SD-R1312 Combo Drive Rear Panel - Connectors Power Connector Power is supplied to your DVD d rive by the connection with your computer's +5V/+12V power cable to the power socket at the back of dri ve.
14 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
An important point after buying a device Toshiba SD-R1312 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba SD-R1312 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba SD-R1312 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba SD-R1312 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba SD-R1312 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba SD-R1312, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba SD-R1312.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba SD-R1312. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba SD-R1312 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
