Instruction/ maintenance manual of the product SD-M1712 Toshiba
Go to page of 16
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-M1712 D VD-R OM DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the D VD- R OM Drive .......................
1 INTR ODUCTION – SD-M1712 D VD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (ej ect button, software, emergency eject hole ) Average Random Access Time CD-ROM 85ms DVD 95ms DV.
CD • CD-D A • CD+(E)G • CD-MIDI • CD-TEXT • CD-R OM • CD-ROM-XA • CD-I Bridge (Photo-CD , Video CD) • CD-I • Multi-session (Photo-CD , CD Extra, CD-RW , CD-R) • CD-R (Read) • CD-RW (Read) Front Panel Figure 1.SD-M1712 DVD-ROM Drive Front Panel Loading Tray Load disc using tray.
3 SETUP – SD-M1712 D VD-ROM The following steps must be perfo rmed to properly install your drive: • Set Drive J umper Settings • Connect A udio Cab le (optional) • Attach IDE BUS Cable • Attach P ow er Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pi n s located on the rear of the DVD-ROM drive.
4 Placing DVD-ROM Drive inside your Computer Now that you have set the jumpers, you are read y to install your DVD- ROM drive inside your computer. Important Note: Disconnect power fr om your co mputer system before b eginning installation. Remove computer co ver and faceplate if required.
5 Audio Cable (optional) - If you have a sound card and speakers, and would like t o play audio CDs on your computer, you will need to install a CD/DVD audio ca ble. Toshiba's DVD-ROM dri ves use a standard 4-pin audio cable that can be purcha sed from most local computer suppliers.
6 USING THE D VD D VD-R OM Drive – SD-M1712 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
7 Usage Guidelines • K eep the disc tra y closed when not using the D VD-ROM Drive . • Do not press do wn on the disc tra y when opening or clo sing it. • Do not place objects on the disc tra y . • Ne ve r use a damaged, broken, or def or med disc.
8 TR OUBLESHOO TING – SD-M1712 Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instr uctions to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
9 SPECIFICA TIONS –SD-M1712 General Interface ATAPI Compatible DVD-ROM Standards DVD DVD-ROM (DVD-5, DV D-9, DVD-10, DV D-18) DVD-R, DVD-RW, D VD-RAM CD CD-DA CD-ROM CD-I Bridge (Photo-CD, Video CD) Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-MINI CD-TEXT CD+(E)G CD-ROM-XA CD-I CD-R (Read) CD-RW (Read) Storage Capacities DVD 4.
10 Performance Rotational Speed DVD-ROM (6.0X - 16X) single layer 9,200rpm (4.1X - 10X) dual layer 6,300rpm DVD-R (Ver 2.0), DVD-RW (2 - 4.8X) 2,780rpm DVD-R (Ver 1.0) (2 - 4.8X) 3,200rpm DVD-RAM (Ver 1.0) (2X) 2,160 - 4,800rpm DVD-RAM (Ver 2.1) (1X) 1,380 - 3,300rpm DVD-Video CSS-disc (2 - 4.
11 Spin-up Time DVD 1.5s Typ DVD-RAM (Ver 2.1) 1.5s Typ DVD-RAM (Ver 1.0) 1.9s Typ CD 1.4s Typ Data Buff er 192Kb ytes Reliability MTBF 100,000 hours P ower ON Hours 5,436 hours/y ear ON/OFF Cycles 313 cycles/ye a Number of Access 600,000 accesses/y ear Operating Duty Cycle 20% of P ower ON time (Reading/Seeki ng) MTTR 0.
12 Power DC Voltage and Current Requi rements 5V 5%, 12V 5% +5V +12V Sleep Standby Idle Random Access (average) 200mA 240mA 410mA (DVD) 430mA (CD) 660mA (DVD) 600mA (CD) 0mA 0mA 50mA (DVD) 50mA (CD) 730mA (DVD) 830mA (CD) Physical Height 5.75" (146mm) Width 1.
13 DRIVE CONNECT ORS –SD-M1712 Figure 1.SD-M1712 DVD-ROM Dri ve Rear Panel - Connectors Power Connector Power is supplied to your DVD-ROM drive b y the connection with your computer's +5V/+12V power cable to the powe r socket at the back of drive.
14 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
An important point after buying a device Toshiba SD-M1712 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba SD-M1712 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba SD-M1712 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba SD-M1712 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba SD-M1712 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba SD-M1712, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba SD-M1712.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba SD-M1712. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba SD-M1712 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
