Instruction/ maintenance manual of the product SD-M1612 Toshiba
Go to page of 17
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-M1612 D VD-R OM DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the D VD- R OM Drive .......................
1 INTR ODUCTION – SD-M1612 D VD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (ej ect button, software, emergency eject hole ) Average Random Access Time CD-ROM 85ms DVD 95ms DV.
CD • CD-D A • CD+(E)G • CD-MIDI • CD-TEXT • CD-R OM • CD-ROM-XA • CD-I Bridge (Photo-CD , Video CD) • CD-I • Multi-session (Photo-CD , CD Extra, CD-RW , CD-R) • CD-R (Read) • CD-RW (Read) Front Panel Figure 1.SD-M1612 DVD-ROM Drive Front Panel Loading Tray Load disc using tray.
3 SETUP – SD-M1612 D VD-ROM The following steps must be performe d to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable (o ptional) • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pi n s located on the rear of the DVD-ROM drive.
4 Placing DVD-ROM Drive inside your Computer Now that you have set the jumpers, you are read y to install your DVD- ROM drive inside your com puter. Important Note: Disconnect power fr om your co mputer system before b eginning installation. Remove computer co ver and faceplate if required.
5 Audio Cable (optional) - If you have a sound card and speakers, and would like t o play audio CDs on your computer, you will need to install a CD/DVD audio ca ble. Toshiba's DVD-ROM dri ves use a standard 4-pin audio cable that can be purchased from mo st local computer suppliers.
6 USING THE D VD D VD-R OM Drive – SD-M1612 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
7 Removing a Disc To remove a disc from the DVD-RO M drive, perform the following steps: 1. Open the Loading T r ay by pressing the Eject Button. 2. Grasp disc by edges , and lift out of loading tra y . 3. Press Eject Button again to close Loading T ray .
8 NOTE: Use a bar that is less than 1.5 mm in diameter . Do not insert more than 50mm in depth. Inserting more than 50mm may damag e the DVD-ROM drive. Handling Media DVD media is sensitive to dust and fingerprints. Carefully han dle media by its edges only.
9 TR OUBLESHOO TING – SD-M1612 Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instructi ons to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
10 SPECIFICA TIONS –SD-M1612 General Interface ATAPI Compatible DVD-ROM Standards DVD DVD-ROM (DVD-5, DV D-9, DVD-10, DVD- 18) DVD-R, DVD-RW , DVD-RAM CD CD-DA CD-ROM CD-I Bridge (Photo-CD, Video CD) Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-MINI CD-TEXT CD+(E)G CD-ROM-XA CD-I CD-R (Read) CD-RW (Read) Storage Capacities DVD 4.
11 Performance Rotational Speed DVD-ROM (6.0X - 16X) single layer 9,200rpm (4.1X - 10X) dual layer 6,300rpm DVD-R (Ver 2.0), DVD-RW (2 - 4.8X) 2,780rpm DVD-R (Ver 1.0) (2 - 4.8X) 3,200rpm DVD-RAM (Ver 1.0) (2X) 2,160 - 4,800rpm DVD-RAM (Ver 2.1) (1X) 1,380 - 3,300rpm DVD-Video CSS-disc (2 - 4.
12 Reliability MTBF 100,000 hours P ower ON Hours 5,436 hours/y ear ON/OFF Cycles 313 cycles/ye a Number of Access 600,000 accesses/y ear Operating Duty Cycle 20% of P ower ON time (Reading/Seeki ng) MTTR 0.
13 Power DC Voltage and Current Requi rements 5V 5%, 12V 5% +5V +12V Sleep Standby Idle Random Access (average) 280mA 300mA 580mA (DVD) 600mA (CD) 930mA (DVD) 850mA (CD) 0mA 0mA 50mA (DVD) 50mA (CD) 710mA (DVD) 870mA (CD) Physical Height 5.75" (146mm) Width 1.
14 DRIVE CONNECT ORS –SD-M1612 Figure 1.SD-M1612 DVD-ROM Dri ve Rear Panel - Connectors Po w e r Connector P ower is supplie d to your D VD -ROM drive by t he connection with y our computer's +5V/+12V pow er cabl e to the pow er soc ket at the back of drive .
15 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
An important point after buying a device Toshiba SD-M1612 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba SD-M1612 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba SD-M1612 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba SD-M1612 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba SD-M1612 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba SD-M1612, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba SD-M1612.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba SD-M1612. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba SD-M1612 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
