Instruction/ maintenance manual of the product SD-M1201 Toshiba
Go to page of 8
SD-M1201 D VD-R O M with REALmagic Hollywood+ Playback Card Installation Instructions Congratulations on your purchase of a T oshiba SD-M1201 D VD-R OM dri ve and REALmagic Hollyw ood+ D VD/MPEG-2 Playback Card Kit. The following information will help you in the simple installation of your ne w D VD-ROM.
The follo w steps must be performed to properly install y our D VD-R OM. l Set D VD-R OM drive jumper settings. l Connect audio cable. l Install SCSI host adapter board. l Attach SCSI interface cable. l Mount D VD-R OM. SETTING JUMPERS The block of mode select jumpers are located on the rear of the DVD- R OM.
PR V/AL W - This jumper is used to inhibit the dri ve’ s EJECT button. When the jumper is ON, the EJECT button will not operate. T est - This setting selects the dri ve operation between normal CD-R OM and CD-Audio player mode. When jumper is set to ON position, com- mands from the host computer are ignored.
4 If you ar e r eplacing your CD-R OM : connect DVD-R OM to the SCSI interface connector that the CD-R OM was connected to. If D VD-ROM is not r eplacing a CD-R OM or is an addition to a CD-R OM: daisy-chain the D VD-R OM dri ve with a custom built SCSI interf ace cable (not supplied with kit).
5 Daisy-Chaining - If the D VD-R OM you are installing is one of two or more SCSI devices you are connecting to your system, you will need to use a custom built SCSI interface cable. Remember that the terminator jumper on the D VD-R OM dri v e must ha ve the jumper installed when the drive is the last device in the chain.
2.5 - 3.5mm Surface of side or bottom of DVD-ROM drive Mounting frame of host computer Mounting Screw M3 6 COMPLETING INST ALLA TION After you ha ve connected all the necessary cables, push the D VD-R OM completely into the computer’ s drive slot. Mount drive accord- ing to your computer’ s instruc- tions.
D VD-R OM BA CK P ANEL The photo illustrates the follo wing features of the SD-M1202 D VD-ROM back panel: ① Analog audio out connector ② Mode select jumper ③ SCSI interface connector ④ Power c.
SD-M1201 SPECIFICA TIONS D V D CD-ROM Data Capacity (bytes/block) 2,048 mode 1 mode 2 2,048 2,336 Rotational Speed (approx. rpm) 2,900 13.8 ~ 32X: 6,900 8.6 ~ 20X: 4,300 (CD-RW) 4 ~ 5.7X: 1,200-2,000 (audio) Sustained Data Transfer Rate 2,797 ~ mode 1 mode 2 (kbytes/sec) 6,760 2,069 ~ 2,360 ~ 4,800 5,475 Access T ime (T yp.
An important point after buying a device Toshiba SD-M1201 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba SD-M1201 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba SD-M1201 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba SD-M1201 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba SD-M1201 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba SD-M1201, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba SD-M1201.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba SD-M1201. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba SD-M1201 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
