Instruction/ maintenance manual of the product 38515 Toro
Go to page of 12
Form No. 3360-738 Rev A CCR™ 2450 GTS ® Snowthrower Model No. 38515—Serial No. 290000001 and Up Operator's Manual Introduction R ead this infor mation carefully to lear n ho w to operate and maintain your product properly and to av oid injur y and product damage.
T raining • R ead, understand, and follow all instr uctions on the machine and in the man ual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Kno w ho w to stop the unit and diseng age the controls quickly .
• Disengag e po wer to the rotor blades when sno w throw er is transported or not in use. • Never operate the sno w thro wer without g ood visibility or light. Always be sure of your footing, and keep a r m hold on the handles . W alk; never r un.
Safety and Instructional Decals Important: Safety and instr uction decals are located near areas of potential danger . Replace damaged decals. 60-9480 104-2767 104-2775 104-4135 105-1978 Reorder part no.
105-1980 Reorder part no. 105-3521 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty . Use 1. No parts required – Unfold the handle. Discharge chute 1 Chute handle 1 Phillips head screws 3 W ashers 3 2.
3. Hook the end of the control cable spring into the bottom hole of the control bar (Figure 4). Figure 4 4. Fully inser t the handle bolts (Figure 5). Important: Ensure that you do not pinch the control ca ble (Figure 5). Figure 5 5. Tighten the knobs until they are sn ug .
Figure 8 1. Key switch 3. Recoil start 2. Primer 4. Choke lever Operation Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. Gasoline is extremely ammable and explosi v e. A re or explosion from gasoline can bur n y ou and others.
Starting the Engine 1. T urn the ignition key clockwise to the On position (Figure 11). Figure 1 1 2. Mov e the chok e lever to the right (Figure 12). Figure 12 3. Fir mly push in the primer 2 times with your thumb , holding the primer in for a second before releasing it eac h time (Figure 13).
Adjusting the Discharge Chute T o adjust the discharge chute , mo v e the chute handle and the chute deector handle as shown (Figure 18). Figure 18 1. Chute handle 2. Chute deector handle Preventing Freeze-up after Use • Let the engine r un for a few min utes to prev ent moving par ts from freezing .
Adjusting the Control Cable Checking the Cable Ser vice Inter v al: After the rst hour Y early—Chec k the control cable and adjust it if necessary . Important: Check the control ca ble for proper adjustment initially , after the r st operating hour, and then annually thereafter .
Inspecting the Rotor Blades Ser vice Inter v al: Y early Before eac h season, inspect the rotor blades for wear . When a rotor blade edge has worn do wn to the w ear indicator hole , hav e an A uthorized Ser vice Dealer replace the rotor blades and the scraper (Figure 22) Figure 22 1.
Conditions and Products Covered under The T oro Starting Guarantee The T oro Company and its af fi liate, T oro W arranty Company , guarantee that your T oro GTS (Guaranteed to Start) engine, when us.
An important point after buying a device Toro 38515 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toro 38515 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toro 38515 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toro 38515 you will learn all the available features of the product, as well as information on its operation. The information that you get Toro 38515 will certainly help you make a decision on the purchase.
If you already are a holder of Toro 38515, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toro 38515.
However, one of the most important roles played by the user manual is to help in solving problems with Toro 38515. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toro 38515 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
