Instruction/ maintenance manual of the product WB-31 Toa
Go to page of 12
FLAT LCD DISPLAY MOUNT MODEL INSTALLATION MANUAL WB-31 Swingout Arm Mount.
WB-31 T ABLE OF CONTENTS Parts List 4 Installation T ools 4 5 d u t s d o o W - n o i t a l l a t s n I e t a l p k c a B 6 e c a f r u S e t e r c n o C - n o i t a l l a t s n I e t a l p k c a B 7 .
WB-31 Installation Instructions Page 3 W arning S tatements W ARNING : THE W ALL STRUCTURE MUST BE CAP ABLE OF SUPPOR TING A T LEAST A MAXIMUM WEIGHT OF 50 LBS. IF NOT , THE W ALL MUST BE REINFORCED. PROPER INST ALLA TION PROCEDURE BY A QUALIFIED SER VICE TECHNICIAN, AS OUTLINED IN THE INST ALLA TION INSTRUCTIONS, MUST BE ADHERED T O.
WB-31 Page 4 Installation Instructions Parts List NOTE : This mount is shipped with all intallation hardware and components. Make sure that none of these parts are missing and/ or damaged before beginning installation. If there are parts missing and/or damaged, please stop and contact TOA Electronics, Inc.
WB-31 Installation Instructions Page 5 Backplate Installation - W ood S tud NOTE : These installation instructions will apply to the WB-31 Swingout Arm Mount. The following steps will outline how the back plate will be mounted. 1. Determine where the mount location will be.
WB-31 Page 6 Installation Instructions Backplate Installation - Concr ete Surface NOTE : These installation instructions will apply to the WB-31 Swingout Arm Mount. The following steps will outline how the back plate will be mounted. 1. Determine where the mount location will be.
WB-31 Installation Instructions Page 7 WB-31 Installation 1. The reverse side of the mount must be mounted to the back plate that is attached to the wall.
WB-31 Page 8 Installation Instructions Figure 7. Cable Routing Installing the Monitor 1. Loosely tighten two (2) M4 x 10mm Phillips Head screws to the top of the mounting points.
WB-31 Installation Instructions Page 9 Adjusting the Swingout Arm This unit comes pre-tensioned at the factory . T o adjust the swingout Arm so that there will not be any move- ment, perform the following steps (Figure 8). 1. Remove the Plastic End Caps.
WB-31 Page 10 Installation Instructions Adapter Plate Installation NOTE : If your flat panel is not a VESA 75/100, the 200x200 or the 100x200 Adapter Plates must be used. 100x200 Aapter Plate 1. Attach the 100x200 Adapter Plate to the back of the display using the provided hardware (see Parts List, page 4).
WB-31 Installation Instructions Page 1 1 T echnical Specifications Figure 1 1. WB-31 Swingout Arm.
WB-31 Page 12 Installation Instructions IN-WB31.R2 W ALL MOUNT Mfg. Date PN E255449 29GZ.
An important point after buying a device Toa WB-31 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toa WB-31 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toa WB-31 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toa WB-31 you will learn all the available features of the product, as well as information on its operation. The information that you get Toa WB-31 will certainly help you make a decision on the purchase.
If you already are a holder of Toa WB-31, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toa WB-31.
However, one of the most important roles played by the user manual is to help in solving problems with Toa WB-31. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toa WB-31 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
