Instruction/ maintenance manual of the product VFST-CMN-2 TOA Electronics
Go to page of 24
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 1 Unvented Decorative Gas Fireplaces P/N 903571 REV. H 12/2007 VFST -CMN-2 VFPF-CMN-2 VFST -CMP-2 VFPF-CMP-2 MODELS ST ANDARD SERIES FOR USE ONLY WITH DECORATIVE TYPE UNVENTED ROOM HEATERS. DO NOT BUILD A WOOD FIRE.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 2 Caulking materials (noncombustible) Fireplace surround materials Check the inventory list to be sure that you have all the necessary parts in usable condition. Also check for concealed damage. IMPORTANT SAFETY INFORMATION INSTALLER: PLEASE LEAVE THESE INSTRUC- TIONS WITH THE OWNER.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 3 Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning are similar to the flu with headaches, dizziness and/or nausea.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 4 Your options are: a. Rework equations adding the space of ad- joining room(s). If the extra volume provides an unconfined space, then remove door or add ventilation grills between rooms. Refer to National Fuel Gas Code, ANSI Z223.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 5 Carefully inspect the heater case and contents for shipping damage and immediately inform the dealer from whom you purchased the gas fireplace if any damage is found. The appliance is shipped with all gas controls and components installed and pre-wired.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 6 VFST FRAMING SPECIFICATIONS VFST APPLIANCE SPECIFICATIONS C A B Gas Line 2 x 4 Wall Framing T op View *1/2" (13mm) Required Air Space Clearance D.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 7 Figure 6 Figure 7 Figure 8 C A B Gas Line VFPF FRAMING SPECIFICATIONS VFPF APPLIANCE SPECIFICATIONS Gas Line Energy Wall 2 x 4 Outside Wal l Drywall Dr ywall * Bracket Bracket Framing T op View * 1/2" (13mm) Required Air Space Clearance A 22-3/4" (578 mm)* B 40-1/8" (1016 mm) Min.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 8 All appliances have a 3" long 3/8" NPT nipple installed at the valve. To quickly and easily complete the gas line routing, use the gas flex line kit, Model GFLV. Figure 9 Step 3 . Remove the nailing flanges from the lower control compartment and install in place with three (3) screws each.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 9 Finished Wall Details It is sometimes best to frame the appliance after it has been positioned in place. Frame with 2 x 4s or heavier lumber. Always frame in accordance with local building codes. Note: The header may rest on the top spacers but must not be notched to fit around them.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 10 Figure 15 Figure 17 Pilot Cut Out Assembling the Logs WARNING: DO NOT ADD EXTRA LOGS OR ORNAMENTS SUCH AS PINE CONES, VER- MICULITE OR ROCK WOOL. USING THESE ADDED ITEMS CAN CAUSE SOOTING. WARNING: DO NOT PLACE ANY LAVA ROCK ON LOGS OR BURNERS.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 11 Figure 19 OPTIONAL EQUIPMENT An incomparable package of options are avail- able for use with these appliances. These op- tions can both customize the operation of these unique appliances and enhance their beauty and charming appeal.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 12 Optional on Unit Rocker Switch An optional rocker switch kit can be installed directly on all VFST series appliances to provide for On and Off operation in lieu of a wall switch.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 13 ACCESSORIES AND COMPONENTS Forced Air Kit FAB-1100 RCL Remote Control Kit RCL-STAT Rocker Switch Kit FRS Wall Switch Kit FWSK REPLACEMENT PARTS An exploded view of the room heater with numbered parts and a parts list can be found on page 19.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 14 Gas Flex Line Kit FFGC Brass Louvers –Main Panel VF6-BRLK –End Panel VF6-BRLEK Note: Model DAT-6-4 may not be used in conjunction with Model SPK-6. Note: Model DAT-6-1 may not be used in conjunction with Model SPK-6.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 15 1. When igniter button is pressed, there is no spark at ODS/pilot. 2. Heater produces unwanted odors. 3. Heater shuts off in use (ODS operates). 4. Gas odor even when control knob is in “OFF” position.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 16 OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS 1. Stop! Read the safety information above. 2. Make sure manual shut-off valve is fully open. 3. Locate gas control knob and piezo.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 17 Note: Knob cannot be turned from “PILOT” to “OFF” unless the knob is pushed in slightly. Do not force.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 18 VFST REPLACEMENT PARTS LIST VFST-CMN VFST-CMP No. Description Part No. Qty. Part No. Qty. 1. Valve - Millivolt 903489 1 901917 1 2. Injector, Burner 110389 2 110384 2 3. Pilot 110344 1 901915 1 4. Regulator, Pilot 903218 1 112081 1 5.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 19 REPLACEMENT PARTS – VFST 7 8 6 2 14 1 4 9 10 12 15 13 12 3 16 5 11.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 20 VFPF REPLACEMENT PARTS LIST VFPF-CMN VFPF-CMP No. Description Part No. Qty. Part No. Qty. 1. Valve - Millivolt 903489 1 901917 1 2. Injector, Burner 110389 2 110384 2 3. Pilot 110344 1 901915 1 4. Regulator, Pilot 903218 1 112081 1 5.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 21 REPLACEMENT PARTS – VFPF 15 12 16 20 19 19 9 18 13 12 1 14 3 6 2 1 10 9 17 4 7 8 5 11.
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 22 NOTE: THIS PAGE INTENTIONALLY LEFT BLANK..
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 23 NOTE: THIS PAGE INTENTIONALLY LEFT BLANK..
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 24 Printed in U.S.A. © 1998 by Lennox Hearth Products P/N 903571 REV. H 12/2007 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
An important point after buying a device TOA Electronics VFST-CMN-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics VFST-CMN-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics VFST-CMN-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics VFST-CMN-2 you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics VFST-CMN-2 will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics VFST-CMN-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics VFST-CMN-2.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics VFST-CMN-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics VFST-CMN-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
