Instruction/ maintenance manual of the product NH TS100-135A Tiger Products Co., Ltd
Go to page of 20
PAGE - 1 INSTRUCTIONS SWEEPER ASSEMBLIES NH TS100-135A 06020012 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.
PAGE - 2 FORWARD 2 TABLE OF CONTENTS 2 SAFETY PERCAUTIONS 3 OPERATIONAL SAFETY PRECAUTIONS 4 OPERATION 5 IMPORTANT INSTRUCTIONS 7 MOUNTING INSTRUCTIONS 8 LEVELING INSTRUCTIONS 10 SUPPORT YOKE ADJUSTME.
PAGE - 3 This symbol means: CAUTION ! Your safety is at rick ! – Any R.O.P.S. (roll over protective structure) should not be drilled, welded on, or altered in any manner. Any alteration may reduce your protection. – Do not bypass the tractor neutral safety swith.
PAGE - 4 OPERATIONAL SAFETY PRECAUTIONS This symbol means: CAUTION ! Your safety is at rick ! – Reduce speed when turning, taking curves, rough ground, or hillsides to reduce chance of rollover. – Always keep tractor in gear when traveling downhill to prevent runaway.
PAGE - 5 OPERATION Be sure the ball valves on the mower hydraulic tank are OPEN before starting the tractor. Serious damage to the hydraulic system can occur if the valves are not OPEN. For brush operation: open the high pressure valve located near the pressure port of the pump and close the high pressure valve located near the electrical solenoid.
PAGE - 6 It is very possible to cut brush life by 50% if the frame is not level. Running an unlevel brush is jast like throwingmoney out the window. The small amount of time spent leveling a brush before sweeping is paed back many times over in longer brush life.
PAGE - 7 1. Do not store sweeper polypropylene brushes in direct sunlight! Direct sunlight will cause the bristles to deteriorate, causing the bristles to become brittle. If the broom is to be stored for any length of time, store it in the shade, inside, or cover the brush with a tarp to protect it from the sun.
PAGE - 8 MOUNTING INSTRUCTIONS Please rea and understand the instructions and schematics completely before beginning assembly. Parts and drawings may vary slightly due to the variety of tractor makes and models. The mounting kit you receive should be correct for your application.
PAGE - 9 11. The spring - chain assemblies are used to help support the weight of the brush head assembly when in the sweeping position. Hook on spring to each of the outside holes in the top plate of the brushhead upright. The chains are con nected to the outside slots in the chain holder on the spring - chain assembly.
PAGE - 10 LEVELING INSTRUCTIONS The sweeper must be leveled t maintain even brush wear and to produce efficient sweeping action. If the broom is not leveled at first and periodically after that, then it will put stress on certain parts causing excessive wear.
PAGE - 11 Make a note of the measurements. Swing the brush head assembly to the left and take the same measurements. If the measurements are not equal, refer to previous leveling steps and illustrations for adjustments. LEVELING INSTRUCTIONS CONTINUED 5.
PAGE - 12 SUPPORT YOKE ADJUSTMENT NOTE: This section applies only to units with serial number 75146 and above. Units with serial number below 75146 do not have adjustable support yokes. Before operating the sweeper the brush head frame support yokes should be checked and if necessary adjusted as follows: 1.
PAGE - 13 BRUSH REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place.
PAGE - 14 MOTOR AND HUB REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place.
PAGE - 15.
PAGE - 16 TRACTOR MOUNT - MAIN FRAME.
PAGE - 17 TRACTOR MOUNT - MAIN FRAME ITEM PART NO. QTY. DESCRIPTION 1 34857 1 MTG,THS 2 06410443 1 MNT,LH,SWPR,CNH,TSA 2 06410442 1 MNT,RH,SWPR,CNH,TSA 4 06430049 4 SPACER,2.00x1.00x3.34 5 41644 1 PLATE,ATTACHING 6 21735 4 CAPSCREW,1/2 x 2 1/2,NC 7 24879 4 CAPSCREW , 20MM x 65MM(2.
PAGE - 18.
PAGE - 19.
PAGE - 20.
An important point after buying a device Tiger Products Co., Ltd NH TS100-135A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tiger Products Co., Ltd NH TS100-135A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tiger Products Co., Ltd NH TS100-135A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tiger Products Co., Ltd NH TS100-135A you will learn all the available features of the product, as well as information on its operation. The information that you get Tiger Products Co., Ltd NH TS100-135A will certainly help you make a decision on the purchase.
If you already are a holder of Tiger Products Co., Ltd NH TS100-135A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tiger Products Co., Ltd NH TS100-135A.
However, one of the most important roles played by the user manual is to help in solving problems with Tiger Products Co., Ltd NH TS100-135A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tiger Products Co., Ltd NH TS100-135A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
