Instruction/ maintenance manual of the product TPS22922B Texas Instruments
Go to page of 17
TPS22921/22/22B Load Switch EVM User's Guide Literature Number: SLVU286 January 2009.
2 SLVU286 – January 2009 Submit Documentation Feedback.
Contents 1 TPS22921/22/22B Load Switch Evaluation Module (EVM) ................................................ 5 1.1 Introduction ................................................................................................................... 5 2 Schematics and Bill of Materials .
www.ti.com List of Figures 3-1 TPS22921/22/22B EVM Component Placement ........................................................................ 9 3-2 TPS22921/22/22B EVM Top-Side Layout .................................................................
1.1 Introduction Chapter 1 SLVU286 – January 2009 TPS22921/22/22B Load Switch Evaluation Module (EVM) This user's guide describes the TPS22921/22/22B evaluation module (EVM). This guide contains the EVM schematics, bill of materials, assembly drawings, and top and bottom board layouts.
TPS22921/22/22B Load Switch Evaluation Module (EVM) 6 SLVU286 – January 2009 Submit Documentation Feedback.
2.1 EVM Options 2.2 Schematic A2 B2 C2 A1 B1 C1 U1 TPS22921/22/22B R1 33 R2 330 R3 R OUT1 C OUT1 C IN1 C IN2 C OUT2 R OUT2 R4 C5 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 J6 OUT RES J5 OUT CAP J4 IN CAP C6 1 F µ 1 F µ 10 F µ 0.
2.3 Bill of Materials Bill of Materials www.ti.com Table 2.4. Bill of Materials QTY REFDES VALUE DESCRIPTION SIZE PART NUMBER MFR -01 -02 -03 1 1 1 – – Two-layer, 2420 × 2320 mil, PCB 2420 × 232.
3.1 TPS22921/22/22B EVM Board Chapter 3 SLVU286 – January 2009 Board Layout This section contains three views of the TPS22921/22/22B EVM evaluation board as well as some layout considerations.
TPS22921/22/22B EVM Board www.ti.com Figure 3-2. TPS22921/22/22B EVM Top-Side Layout Figure 3-3. TPS22921/22/22B EVM Bottom-Side Layout Board Layout 10 SLVU286 – January 2009 Submit Documentation Fe.
3.2 Layout Considerations www.ti.com Layout Considerations The V IN and V OUT pins of U1 can carry significant current; so, traces to these pins should be of suitable length and width to minimize voltage drop to the load. Locate the C IN and C OUT bypass capacitors close to the V IN and V OUT pins of U1.
Board Layout 12 SLVU286 – January 2009 Submit Documentation Feedback.
4.1 Recommended Test Equipment 4.2 Calculating Voltage Drop and Load Current Oscilloscope V oltage probe 3.6 V , 2 A Max 7” twisted pair , #20 A WG + IN – + OUT – EVM V oltage probe Chapter 4 SL.
EVM Setup 14 SLVU286 – January 2009 Submit Documentation Feedback.
Chapter 5 SLVU286 – January 2009 Related Documentation from Texas Instruments • TPS22921, TPS22922, TPS22922B, Low-Input Voltage, Ultra-Low r ON Load Switches data sheet (SLVS749) SLVU286 – Janu.
EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
An important point after buying a device Texas Instruments TPS22922B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments TPS22922B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments TPS22922B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments TPS22922B you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments TPS22922B will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments TPS22922B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments TPS22922B.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments TPS22922B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments TPS22922B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
