Instruction/ maintenance manual of the product VX4353 Tektronix
Go to page of 62
User Manual VX4353 Relay Switching Module 070-9121-02 This document supports firmware version 1.00 W arning The servicing instructions are for use by qualified personnel only . T o avoid personal injury , do not perform any servicing unless you are qualified to do so.
Copyright T ektronix, Inc. All rights reserved. Licensed software products are owned by T ektronix or its suppliers and are protected by United States copyright laws and international treaty provisions.
.
.
Contacting T ektronix Product Support For application-oriented questions about a T ektronix measure- ment product, call toll free in North America: 1-800-TEK-WIDE (1-800-835-9433 ext. 2400) 6:00 a.m. – 5:00 p.m. Pacific time Or contact us by e-mail: tm_app_supp@tek.
.
EC Declaration of Conformity We T ektronix Holland N.V . Marktweg 73A 8444 AB Heerenveen The Netherlands declare under sole responsibility that the VX4353 meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility and Low V oltage Directive 73/23/ECC for Product Safety .
.
.
.
Appendix E – Performance V erification Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A – 15.
.
! $ # .
.
.
.
.
.
.
.
.
.
.
.
T o avoid electric shock, tighten the module mounting screws after installing the module into the mainframe to ensure that the front panel is properly grounded. Ther e ar e two labeled printed ejector handles on the card. T o install the car d corr ectly , make sur e the ejector labeled “VX4353” is at the top.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
070-9121-02.
VX4353 Page A – 15 Appendix E Performance V erification Procedure The performance verification procedure verifies that the module is operating within specification. Conventions Used In This Procedur e All control of the VX4353 Module will be accomplished through a VXI Slot 0 device.
VX4353 Page A – 16 Equipment Required T able 1–1 lists the equipment required for the performance and verification procedure. T able 1–1: Equipment Required Required tools and equipment Part number VXI Mainframe (such as the T ektronix VX1410) n/a VXI Slot 0 with resource Manager (T ektronix VX4521) and appropriate cables and interface cards.
VX4353 Page A – 17 Digital Multi-Meter Connection and Set Up 1. Connect the DMM signal high and input + side to the “pig tail” that is connected to the VX1780S connector pin-1. 2. Connect the DMM signal low and input – side to the “pig tail” that is connected to the VX1780S connector pin-2.
VX4353 Page A – 18 T esting The Delay Command 1. Send “R lf ” (Reset the VX4353) to the VX4353. 2. Send “D1000C0C1” (Reset, Close CH00 and CH01 on the VX4353) to the VX4353. a. Monitor the time difference between the time it takes for the CH00 LED to light, and the time for the CH01 LED to light.
An important point after buying a device Tektronix VX4353 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tektronix VX4353 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tektronix VX4353 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tektronix VX4353 you will learn all the available features of the product, as well as information on its operation. The information that you get Tektronix VX4353 will certainly help you make a decision on the purchase.
If you already are a holder of Tektronix VX4353, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tektronix VX4353.
However, one of the most important roles played by the user manual is to help in solving problems with Tektronix VX4353. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tektronix VX4353 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
