Instruction/ maintenance manual of the product Cost Control Technoline
Go to page of 8
Operating Manual Cost Control - Po wer Consumption Monitor Contents Introduction 1.0 The Cost Control 2.0 Features 3.0 Cost Monitoring 4.0 Cost Forecas ting 5.0 Instantaneous power c onsumption 6.0 The maximum power consumption 7.0 Total power consu mption 8.
pressed once more to confirm the se tting of all digits ( the last digit on the left had side will stop fla shing). 5. Once the Tariff i s set, pl ug the Cost C ontrol into the mains supply and then plug the electrical appliance in to the Co st Control.
Betriebsanleitung Cost Controller Stromverbrauchs-Über wachung Inhalt Vorstellung 1.0 Der Cost Controller 2.0 Merkmale 3.0 Kostenüberwachung 4.0 Kostenvorhersage 5.0 Augenblicklicher Leistu ngsverbrauch 6.0 Maximaler Leistungsv erbrauch 7.0 Gesamtleistungsv erbrauch 8.
1. Drücken und halten Sie die ″ TA RIFF ″ -Taste (etwa 3 Se kunden), bis die am weitesten rechts stehende Zi ffer anfängt zu blinken . 2. Betätigen Sie zur Einstellung der gewünschten Zahl entw eder die ″ POWER ″ - oder die ″ COST ″ -Taste .
Mode d'emploi Moniteur de Consommation Cost Con trol Table des matières Introduction 1.0 Le Cost Control 2.0 Caractéristiques 3.0 Suivi des coûts 4.0 Prévision des coû ts 5.0 Consommation instantanée 6.0 Consommation maximum 7.0 Consommation totale 8.
"POWER" augmente les chiffres de 0 à 9, et "COST" le s fait défiler à rebours de 9 à 0. 3. Une fois qu'un chiffre e st réglé, appuyer une fois sur "TARIFF" pour passer au chiffre suivant. 4. Répéter les étapes 2 et 3 jusqu'à ce que les v aleurs des kWh désirées soient réglées.
Handleiding Kostenmeter – Monitor van Stroomv erbruik Introductie 1.0 De Kostenmeter 2.0 Eigenschappen 3.0 Registratie Kosten 4.0 Prognose Kosten 5.0 Huidig Stroomverbruik 6.0 Maximaal Stroomverbruik 7.0 Totaal Energieverbruik 8.0 Bedoeld Gebruik 9.
2. Druk vervolgens op de ‘POWER” of “C OS T”-knop om het gewenste cij fer in te stellen. Elke kee r drukken doet het getal met één toenemen. De “POWER”-knop vermeerdert het getal v an 0 tot 9, en d e “COST”-knop vermindert het v an 9 tot 0.
An important point after buying a device Technoline Cost Control (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Technoline Cost Control yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Technoline Cost Control - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Technoline Cost Control you will learn all the available features of the product, as well as information on its operation. The information that you get Technoline Cost Control will certainly help you make a decision on the purchase.
If you already are a holder of Technoline Cost Control, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Technoline Cost Control.
However, one of the most important roles played by the user manual is to help in solving problems with Technoline Cost Control. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Technoline Cost Control along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
