Instruction/ maintenance manual of the product 1F80-0471 Technics
Go to page of 16
Index Page Installation 2 Wiring Connections 2 Thermostat Quick Reference 3 Installer Con fi guration Menu 4 Operating Y our Thermostat 6 Programming 6 T roubleshooting 8 Save these instructions for future use! Description Gas or Oil Heat Y es Electric Furnace Y es Heat Pump (No Aux.
Thermostat installation and all components of the control system shall conform to Class II circuits per the NEC code. W ARNING ! INST ALLA TION Remove Old Thermostat A standard heat/cool thermostat consists of three basic parts: 1. The cover , which may be either a snap-on or hinge type.
3 Time Day of Week Setting T emperature Room T emperature T emperature Up/Down HOLD Button SYSTEM Button FA N Button SYSTEM Indicator FA N Indicator MENU/SCHEDULE/RUN Button Displays the po wer lev el of the 2 "AA" batteries: indicates good power le vel.
4 INST ALLER/CONFIGURA TION MENU With thermostat in Heat, Cool or Auto, in normal operation, press the Menu button for at least 5 seconds. The display will show item #1 in the table below . Press Menu to advance to the next menu item. Press or to change an item option.
5 INST ALLER/CONFIGURA TION MENU 4) Energy Management Recovery: (this step is skipped if con fi gured to be non-programmable). Energy Management Recovery (E) On enables the ther- mostat to start heating or cooling early to make the building temperature reach the program setpoint at the time you specify .
6 OPERA TING YOUR THERMOST A T Choose the Fan Setting (Auto or On) Set the F AN Switch to Auto or On . Fan Auto is the most commonly selected setting and runs the fan only when the heating or cooling system is on. Fan On runs the fan continuously for increased air circulation or to allow additional air cleaning.
7 Energy Saving Factory Pre-Program The 1F80-0471 thermostats are programmed with the energy saving settings shown in the table below for all days of the week. If this program suits your needs, simply set the thermostat clock and press the RUN button.
Symptom Possible Cause Corrective Action No Heat/No Cool/No Fan (common problems) 1. Blown fuse or tripped circuit breaker . 2. Furnace power switch to OFF . 3. Furnace blower compartment door or panel loose or not properly installed. 4. Loose connection to thermostat or system.
Instalación 2 Conexiones eléctricas 2 Guía de referencia rápida del termostato 3 Menú instalador/de con fi guración 4 Cómo usar el termostato 6 Programación 6 Solución de problemas 8 www .
La instalación del termostato y de todos los componentes del sistema de control debe ajustarse a las normas del código NEC para los circuitos Clase II. INST ALACIÓN Figura 2 – Base y vista posterior del termostato Retire el termostato viejo Un termostato de calor/frío estándar consta de tres partes básicas: 1.
3 Hora Día de la semana T emperatura de ajuste T emperatura ambiente Subir/Bajar temperatu r Botón HOLD Botón SYSTEM Botón FA N Indicador SYSTEM Indicador FA N Botón MENU/SCHEDULE/RUN Muestra el nivel de carga de las 2 pilas "AA": indica buen niv el de carga.
4 MENÚ INST ALADOR/DE CONFIGURACIÓN Con el termostato en Heat, Cool o Auto, en operación normal, presione el botón Menu durante 5 segundos como mínimo. La pantalla mostrará la opción 1 tal como se describe en la siguiente tabla. Presione Menu para pasar a la siguiente opción del menu.
5 MENÚ INST ALADOR/DE CONFIGURACIÓN Cuando esta función está en OFF (desactivada), no se realizarán cambios cuando el sistema de enfriamiento está funcionando de forma continua durante los períodos de alta demanda. 4) Control de energía (EMR) – (este paso se pasa por alto si se con fi gura como no programable).
6 CÓMO USAR EL TERMOST A TO Elija la con fi guración del ventilador (Auto/On) Coloque el interruptor F AN en Auto (automático) u On (activado). Auto es la con fi guración más comúnmente seleccionada y hace funcionar el ventilador únicamente cuando el sistema de calefacción o enfriamiento está encendido.
7 Pre-programación de ahorro de energía de fábrica Los termostatos 1F80-0471 están programados con los ajustes de ahorro de energía indicados en la siguiente tabla para todos los días de la semana. Si este programa es adecuado para sus necesidades, simplemente ajuste el reloj del termostato y presione el botón RUN.
Síntoma Causa posible Acción correctiva El sistema no cali- enta/El sistema no enfría/No funciona el ventilador (problemas comunes) 1. Se quemó el fusible o se disparó el disyuntor . 2. El interruptor de alimentación del calefactor está en OFF .
An important point after buying a device Technics 1F80-0471 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Technics 1F80-0471 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Technics 1F80-0471 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Technics 1F80-0471 you will learn all the available features of the product, as well as information on its operation. The information that you get Technics 1F80-0471 will certainly help you make a decision on the purchase.
If you already are a holder of Technics 1F80-0471, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Technics 1F80-0471.
However, one of the most important roles played by the user manual is to help in solving problems with Technics 1F80-0471. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Technics 1F80-0471 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center