Instruction/ maintenance manual of the product C722 Taylor
Go to page of 60
Model C 722 So ft S erve Freezer Original Ope ra ting Instruc tions 080568-M 2/22/ 12 (Or igi nal Publ icat ion) Updated 5/ 14/12.
Com plete thi s page for qui ck r efer ence whe n ser vice i s re quir ed: Taylor Distributor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor ma tion found on the data label : Model Num.
Model C7 2 2 Table of Cont ent s Table of Contents Section 1 To the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 ..............................
Table of Cont ent s Mode l C72 2 Table of Contents - P age 2 Prim ing 34 .............................................................. Manual Brush Cleaning 34 ................................................ Draining P roduct From The Fr eezing Cyli nder 35 .
1 Model C7 2 2 To the Insta ller 12041 1 Section 1 To the Installer The f ollowing are general ins tallat ion inst ruct ions. For complet e inst allation det ails, please see t he checko ut card. Installer Safety In all areas of the world, equipment should be installed i n accordanc e with exis ting loc al codes.
2 Model C7 2 2 To the Insta ller This unit m ust be ins talled on a lev el surf ace to avoid t he hazar d of t ipping. E xtr eme car e should be taken i n moving t his equipment f or any reas on. Two or more people ar e required t o saf ely mov e this unit.
3 Mode l C72 2 To the Insta ller 120514 Supply cor ds used with this unit shall be oil-res istant , s heathed f lexible cable not light er t han ordinary poly chloroprene or ot her equivalent synt het.
4 Model C7 2 2 To the Opera tor Section 2 To the Operator Your f reezer has been car efully engineered and manuf actur ed to give y ou dependable operat ion. This unit , when properly operat ed and cared f or, will produce a c onsist ent qualit y produc t.
5 Model C 7 22 Safety Se cti on 3 Sa fety We, at T aylor Company, ar e concerned about the safet y of t he operat or when he or she c omes in contac t wit h the f reez er and its part s. Tay lor has gone to ex trem e eff ort s to des ign and manuf actur e built- in safet y f eatur es to pr otec t bot h you and t he serv ice tec hnician.
6 Model C 7 22 Sa fety 12041 1 S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screw s. S DO NOT rem ove any int ernal oper ating part s (examples: f reez er door, beater, scr aper blades, et c.
7 Model C 7 22 Safety Notes:.
8 Model C 7 22 Operat or Part s Id ent if icati on 120507 Section 4 Operator Parts Identif ication Model C722 Figur e 1.
9 Mo del C722 Op erato r Parts I den ti fi catio n Model C722 Exploded View Par ts Identification ITE M DESCRIPTI ON PART NO. 1 COVER-HOPPER- 14 QT BLACK 041682-BLA 2 OR IFIC E 022465-100 3 O-RI NG- 3/8 OD X . 070W 016137 4 TUBE A.- FEED-SS- 5/32 HOLE X29429-2 5 O-RI NG- .
10 Model C 7 22 Operat or Part s Id ent if icati on Door and Beater Assem bly Figur e 2 ITE M DESCRIPTI ON PART NO. 1 PLUG-PRI ME TWIN 059936 2 O-RI NG- 1/2OD X .
11 Mo del C722 Op erato r Parts I den ti fi catio n X69928-14S Pump A . - Mix S implified S.S . Figur e 3 ITE M DESCRIPTI ON PART NO. 1 ADAPTOR A.- MIX I NLET-SS X80250 2 GASKET-SI MPLIFI ED PUMP 053527 3 CAP-VALVE BODY SS 056874-14 4 O-RI NG- 2-1/ 8 OD X .
12 Model C 7 22 Operat or Part s Id ent if icati on Accessor ies Figur e 4 ITE M DESCRIPTI ON PART NO. 1 LUBRICANT- TAYLOR 047518 2 TOOL-O- RING REMOVAL 048260- WH T *3 SANITI ZER-STERA SHEEN SEE NOTE 4 PAIL- MIX 10 QT 013163 ITE M DESCRIPTI ON PART NO.
13 Mo del C722 Op erato r Parts I den ti fi catio n Br ushes Figur e 5 ITE M DESCRIPTI ON PART NO. 1 BLACK BRISTLE BRUSH 013071 2 DOUBLE END BRUSH 013072 3 WHITE BRI STLE BRUSH (1” x 2”) 013073 ITE M DESCRIPTI ON PART NO.
14 Model C 7 22 Operat or Part s Id ent if icati on Optional Car ts Car t A.-ADA (X 69400) Car t A .-Std (X69425) Figur e 6 ITE M DESCRIPTI ON PART NO.
15 Model C7 2 2 Impor ta nt: To the Opera tor Section 5 Important: To the Operator Model C722 Figur e 7 ITE M DESCRIPTI ON 1 POWER SWITC H 2 LIQUI D CRYSTAL DISPLAY 3 KEYPADS 4 MIX OUT I NDICATORS 5 S.
16 Model C 7 22 Im port ant : T o the Opera tor Sym bol De finitions To bet ter comm unicat e in the I nter national arena, sym bols have replac ed words on m any of our operat or switches , func tion, and fault indicat ors . Your T aylor equipm ent is designed wit h these Int ernat ional symbols .
17 Model C7 22 Impor tant : To the Opera tor Sta ndby Sy mbol During long “No S ale” periods, t he unit c an be placed into t he St andby mode. T his maint ains product t emperat ures below 40° F ( 4.4° C) in bot h the hopper and t he freez ing cylinder , and helps pr event overbeat ing and product break down.
18 Model C 722 Im porta nt: T o the Opera tor Operating S creen D escriptions The f luoresc ent display locat ed in the c enter of t he contr ol panel is normally blank during the daily operation of t he machine. T he display is act ivated when the SE L sym bol or t he Manager's Menu is select ed.
19 Model C7 22 Impor tant : To the Opera tor Manager' s Menu The M anager's M enu is used t o enter the oper ator funct ion display s. T o acc ess t he Menu, touc h the cent er of t he CO NE sym bol on the c ontrol panel on the r ight side of t he machine.
20 Model C 722 Im porta nt: T o the Opera tor Menu Options Touch t he ARRO W s ymbols to m ove up or down thr ough the Menu. Selec t a M enu option by t ouching the SE L sym bol. Ex it t he Menu progr am by s electing EXI T F ROM ME NU or touc h the CO NE sy mbol .
21 Model C7 22 Impor tant : To the Opera tor Enter t he correct m onth, day , and year. Aft er they have been ent ered, t ouch t he SEL s ymbol t o adva nce to the DAYLIGHT SAVING TIME (DST) scr een.
22 Model C 722 Im porta nt: T o the Opera tor Enable the A UTO ST ART T IME by s electing t he UP arrow s ymbol t o move t he arrow to “ Enable.” T ouch the SE L sym bol to adv ance to t he next sc reen.
23 Model C7 22 Impor tant : To the Opera tor The F AULT HIS TO RY sc reen display s a hist ory of the las t 100 f aults. P age numbers ar e displayed in the upper right -hand cor ner. P age 1 cont ains the most recent fault. Use the arrow symb ols to cycle thr ough the hist ory pages .
24 Model C 722 Im porta nt: T o the Opera tor The SYSTEM I NFORMATION is displaye d on three separat e scr eens. The f irs t sc reen cont ains t he contr ol and sof twar e version ins talled in t he machine. (S ee Figur e 34.) SOFTWARE VERSION C722 CONTROL UVC4 VERSION V00.
25 Model C 722 Op erati ng Pro ced ures Section 6 Operating Procedures The M odel C722 is a medium c apacit y sof t s erve machine. Mix is st ored in t he hoppers. T he unit is equipped with a t hree spout door and t wo 2. 8 quart (2.7 lit er) capacit y f reezing c ylinders .
26 Model C 722 Operat in g Pro cedu res Step 5 Inser t t he beater driv e shaft t hrough t he rear shell bearing in t he freez ing cylinder and engage the hex end fir mly int o the dr ive coupling. Figur e 41 USE EXT REM E CAUTI ON when handling the beat er ass embly.
27 Model C 722 Op erati ng Pro ced ures Step 9 Slide the beat er as sembly t he res t of t he way into the f reezing c ylinder. Make sur e the beat er ass embly is in posit ion over the driv e shaf t by t urning t he beater slight ly unt il the beater is proper ly seat ed.
28 Model C 722 Operat in g Pro cedu res Step 13 To ins tall t he fr eezer door, ins ert t he baff le rods thr ough the beat ers in t he fr eezing cylinder s. Figur e 49 Wit h the door seat ed on the f reezer st uds, inst all the handscr ews. Us e the long hands crews on t he top and the s hort hands crews on the bot tom .
29 Model C 722 Op erati ng Pro ced ures Step 18 Slide the piv ot pin t hrough t he draw handles as the handles are ins erted int o t he draw valves . Figur e 54 Note: T his f reezer f eatures thr ee adjust able draw handles to pr ovide port ion cont rol, giving a bet ter consis tent quality to y our produc t and c ontrolling cost s.
30 Model C 722 Operat in g Pro cedu res Mix Pum p Assem bly Step 1 Ins pect t he rubber pump part s. O -rings and gas ket must be in 100% good condit ion for t he pump and entir e machine t o operat e properly. T he o-rings and gasket cannot proper ly ser ve their intended f unct ion if nicks, cuts, or holes in the materi al are pre sent.
31 Model C 722 Op erati ng Pro ced ures 120507 Step 7 Inser t t he valve body cap int o the hole in t he mix inlet adapt er. (See F igure 64. ) Figur e 64 Step 8 Inser t t he mix inlet ass embly int o the pum p cylinder . (See F igure 65. ) Figur e 65 The adapt er mus t be pos itioned int o the not ch located at t he end of t he pump c ylinder.
32 Model C 722 Operat in g Pro cedu res Step 11 Inst all one red o- ring on each end of t he mix f eed tube, and t horoughly lubric ate. (S ee Figur e 68.) Figur e 68 Step 12 Lay the pum p assem bly, pum p clip, cot ter pin, m ix feed t ube, and t he agitat or in t he bott om of t he mix hopper for s anitizing.
33 Model C 722 Op erati ng Pro ced ures 120507 Step 3 While t he solut ion is flowing int o t he freez ing cylinder , t ake part icular c are to br ush-c lean the mix level sens ing probe, t he mix hopper, the m ix inlet hole, t he air/ mix pump, t he pump clip, t he mix f eed tube, t he cott er pin, and t he agitat or.
34 Model C 722 Operat in g Pro cedu res 120507 Note: I f the agit ator should s top t urning during normal oper ation, with sani ti zed h and s , remov e agitat or f rom agit ator drive s haft housing and br ush clean wit h sanitiz ing solution. I nst all the agit ator back ont o the agit ator driv e shaft housing.
35 Model C 722 Op erati ng Pro ced ures Dr aining P roduct Fr om The Freez ing Cylinder Step 1 Wit h a pail beneath t he door s pouts, open t he draw valve. T ouch the W AS H and PUMP s ymbols . IMP ORT ANT! DO NO T all ow t he pu mp to keep running when the dra w va lve is c losed.
36 Model C 722 Operat in g Pro cedu res Step 6 Raise the pr ime plug. Step 7 When a s teady s tr eam of c leaning solut ion is flowing fr om the pr ime plug opening in t he bott om of t he fr eezer door, open t he draw valv e. Draw of f all t he soluti on.
37 Model C 722 Op erati ng Pro ced ures Br ush Cleaning Step 1 Prepar e a sink wit h cleaning/s anitiz ing solution wit h an act ive chlorine c oncent rate of 100 - 200 PPM . USE WARM WAT ER AND FOLLOW THE MANUFACTURER 'S SPECIFICATI ONS. Make sure all brushes provided wit h the f reez er are available for brush c leaning.
38 Model C7 22 Impor tant : Oper at or Che ck list Section 7 Important: Operator Checklist Dur ing Cl eaning and Sani tizing ALWAYS FOLLOW LOCAL HEALTH CODES. Clean in g and san i tiz in g sched u les are govern ed by fe dera l, st ate , or loca l re gulat ory age ncie s, and mu st be f ol lo w ed acco rdi ng l y.
39 Model C7 22 Impor ta nt: Oper at or Che ck list Winter S tor age If t he place of bus iness is to be c losed during t he winter mont hs, it is import ant t o protect t he freezer by following c ert ain precaut ions, part icularly if t he building is subjec t t o fr eezing condit ions.
40 Model C7 22 Impor tant : Oper at or Che ck list Section 8 Troubleshooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed. a. Low on mix. T he MI X OUT light is on. a. Add mix t o mix hopper. Retur n to AUT O m ode. 34 b.
41 Model C7 22 Impor ta nt: Oper at or Che ck list PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 4. The pr oduct is too t hick . a. F reezing c ylinder not primed co rrectly. a. Drain t he f reezing cy linder and reprim e the mac hine. 34 b. Air /m ix pump incor rect ly assem bled.
42 Model C7 22 Impor tant : Oper at or Che ck list PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 11. Exc essive mix leakage into t he drip pan. a. The s eal on drive shaf t is improper ly lubricat ed or is worn. a. Lubric ate pr operly or replace t he seal.
43 Mo del C722 Parts Rep lacemen t S ched ul e Section 9 Parts Replacement Schedule PART DESCRIPTI ON EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Scr aper Blade X Drive S haft Seal X Fr eezer Door Gas ket .
Section 10 Parts List 44 Parts List Model C7 22 120413 C72227FW BE - 208-230V 60HZ 1P H & 208-230V 60HZ 3PH - A/C- BRIST O L-( R404A) - ROHS CO MP LI ANT DESCRI PT IO N PART NUMBER QTY. WARR. CLASS RE MARKS ACCUMULATOR-COPPER 2" DIA 10" LG 047062 1 103 ACTUATOR A.
45 Model C 722 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER BRACKET-RECEI VER MOUNT 052990 1 103 BRACKET-VALVE- DANF-LWR 069197 1 103 BRACKET-VALVE- DANF-UPR 080241 1 103 BRUSH-REAR .
46 Parts List Model C7 22 DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER COMPRESSOR TL3G-R134A 047701- 27 1 512 +CAPACITOR- START 60UF-220/ 275V 047703 1 103 +COVER-TERMI NAL-COMPRESSOR 047739 1 103 +DRYER-CAP.
47 Model C 722 Parts List 120424 DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER +O-R ING- 1/2OD X .070W 024278 4 000 +O-RI NG-1/4 OD X .070W 50 DUR 015872 3 000 +O-R ING- 7/8 OD X .
48 Parts List Model C7 22 120424 DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER GU IDE A .-DRIP P AN X51567 1 103 GU IDE A .-DRIP P AN -MIX P UM P X80225 2 103 GUIDE- DRIP PAN 068932 2 103 GUIDE-.
49 Model C 722 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER SHOE-FRONT HELI X *FRONT* 050347 2 000 KIT A. -PUMP- SIMPLI FIED SS/ SH X56200-10 2 000 GASKET-SI MPLIFI ED PUMP VALVE 053527 1 000 O-RI NG- 1-3/ 4 OD X .139W 008904 1 000 O-RI NG- 11/16ODX.
50 Parts List Model C7 22 DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER +SHROUD-DANFOSS 068883 1 103 +SCREW-10- 32X3/8 UNSL HWH SERR 039381 2 000 +GUARD-FAN 028534- 1 1 103 MOTOR-GEAR SENSORLESS BLDC 24V 068542-05 2 103 NUT-STUD- BLACK 2.563 LONG 058764 2 103 NUT-STUD- BLACK 3.
51 Model C 722 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER PLATE-DEC 080158 1 103 PLATE A.- MOTOR MOUNT-R X80145 1 103 PLATE A.- MOTOR MOUNT-L X80147 1 103 PROBE A.
52 Parts List Model C7 22 DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER SHAFT-DRI VE-MI X PUMP-HOPPER 041948 2 103 SHAFT-BEATER * C722* 080617 2 40870 +SEAL-DRI VE SHAFT 032560 2 000 SHELF-DRI P TRAY 068863 1 103 SHELL A.
53 Model C 722 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. PART NUMBER +OVERLOAD-THERM AL-1P- 4.0/ 6.5A 067461- 1J 2 103 STUD-NOSE CONE 055987 4 103 TOOL-O- RING REMOVAL- F REEZER 048260-WHT 1 000 TOOL-MI X PUMP SHAFT REMOVAL 057167 1 000 TRANS.
54 Parts List Model C7 22 C72240FW BE - 220-240V 50HZ 1PH - A/C-BRIST OL - ( R404A) - ROHS CO MPLI ANT - HOPPER AG IT ATOR DESCRI PT IO N PART NUMBER QTY. WARR. CLASS RE MARKS BLOCK-TERMI NAL 2P L1,N 039421 1 103 BRACKET-CAPACI TOR C 059353 1 103 CAPACITOR A.
Model C 722 080525-27 5/12.
Model C 722 080525-40 5/12.
An important point after buying a device Taylor C722 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Taylor C722 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Taylor C722 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Taylor C722 you will learn all the available features of the product, as well as information on its operation. The information that you get Taylor C722 will certainly help you make a decision on the purchase.
If you already are a holder of Taylor C722, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Taylor C722.
However, one of the most important roles played by the user manual is to help in solving problems with Taylor C722. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Taylor C722 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
