Instruction/ maintenance manual of the product WUVCLP-C Bard
Go to page of 12
WALL MOUNT SERIES UV LIGHT PACKAGE Mode l: WUVCLP-A & WUVCLP-C READ THESE INSTRUCTIONS CAREFULLY AND COMPLETE LY BEFORE PROCEEDING WITH THE INSTALLATION LEAVE THE INSTALLATION INST RUCTIONS WITH THE OWNER/O PERATOR OF THE DEVICE AFTER OPENING THE CARTON, UNPACK AND INSPECT THE UNIT AND LAMP FOR DAMAGE.
Page 2 Table of Contents Page No. General Unpacking ...................................................................................................Page 1 Description .................................................................................
Page 3 I. GENERAL This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigati on, treatment, or prevention of any disease or condition.
Page 4 Compatibility Chart: Table 1 WA18*-A WH18*-A WH26*-A SH26*-A WA24*-A WH24*-A WH31*-A SH31*-A WA30*-A WH30*-A WH38*-A SH37*-A WUVCLP-A WA37*-A WH36*-A WH43*-A SH43*-A WA42*-A WH42*-A WH49*-A SH4.
Page 5 II. INSTALLATION B ASIC I NSTALLATION 1. Before doing any service work, the unit disconnect must be turn ed off and locked to prevent injury or death due to electrical shock or contact with moving parts. The thermostat must also be turned off. 2.
Page 6 4. Remove the exterior blower access panel from the wall mount unit and set it aside. (See Figure 2) 5. Using the top screw hole for the blower door panel a s a starting point, drill two ¼ inch holes on each side of the unit to secure the mounting brackets of the WUVCLP.
Page 7 7. Slide the left bracket tight against the left side of the unit. Insert two self drilling screws on the left side of the unit and into the left side mounting bracket of the WUVCLP light assembly. Use the pilot holes in the mounting brackets for alignment.
Page 8 2. Remove outer and inner control panel covers . Install the 3 pin accessory plug from the parts bag into the contro l panel if not alr eady equipped. See figure 7A for side installation on the 5 or 6 ton cabinet size. See figure 7B fo r back installation on the 2 and 3 ton cabinet size.
Page 9 3. Remove outer and inner control panel cove rs. Install the 3 pin accessory plug from the parts bag into the control panel if not already equipped. See figure 6A for side installation the 5 or 6 ton cabinet size. S ee figure 6B for back inst allation on the 2 and 3 ton cabinet size.
Page 10 WARNING: Hazard of Electric Shock • Electric shock can cause serious injury or death • Disconnect power before servicing the light WARNING: Hazard of Ultraviolet Type C Light • Looking directly at the UVC light may c ause permanent eye damage or blindness.
Page 11 IV. WIRING DIAGRAM.
Page 12 P/N 46441700 Rev B 01/04.
An important point after buying a device Bard WUVCLP-C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bard WUVCLP-C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bard WUVCLP-C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bard WUVCLP-C you will learn all the available features of the product, as well as information on its operation. The information that you get Bard WUVCLP-C will certainly help you make a decision on the purchase.
If you already are a holder of Bard WUVCLP-C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bard WUVCLP-C.
However, one of the most important roles played by the user manual is to help in solving problems with Bard WUVCLP-C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bard WUVCLP-C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
