Instruction/ maintenance manual of the product oval 4ft pool Swim'n Play
Go to page of 28
OV AL POOL ASSEMBL Y INSTRUCTIONS Part# 420869-14 313 REGINA A VENUE, RAHW A Y , NEW JERSEY 07065-4891 Phone: (732) 574-1500 • Fax: (732) 574-1551 • www.swimnplay.com • E-mail: info@swimnplay.com DANGER DO NOT DIVE OR JUMP into your pool. Y our pool is approximately 4' deep.
2 CONTRACT INST ALLA TIONS The manufacturer is in no way affiliated with any professional pool installer. Therefore the manufacturer can assume no responsibility for errors in installation by the home owner or said professional installer.
3 SOME FRIENDS TO HELP OUT Hammer Knife Tape Rake 4” Nail Pliers Cloth Tape Center Stake 2 x 4 Sifted Earth or Pre Washed Sand Broom Patio Blocks Carpenters Level Shovel Screwdriver Hoe INTRODUCTION The installation of an average size pool (12' - 30' diameter) will usually require three people to help set it up.
4 INST ALLA TION • ASSEMBL Y STEPS READ CAREFULL Y BEFORE ST ARTING POOL ASSEMBL Y CONSTRUCTION CLOSE-UPS Use the illustrations below as a guide for the assembly of your pool Fig. A Fig. B 6” DELMAR ELAN • OMNI LEXINGT ON POOLS 6” PRINCET ON QUANTUM ZENITH • ST .
5 INST ALLA TION • ASSEMBL Y STEPS READ CAREFULL Y BEFORE ST ARTING POOL ASSEMBL Y CONSTRUCTION CLOSE-UPS Use the illustrations below as a guide for the assembly of your pool Fig. D Fig. F 6” EXTRUDED ALUMINUM POOLS with Box V ertical 9” POOLS Fig.
6 INST ALLA TION • ASSEMBL Y STEPS READ CAREFULL Y BEFORE ST ARTING POOL ASSEMBL Y CONSTRUCTION CLOSE-UPS Use the illustrations below as a guide for the assembly of your pool Fig. H DELUXE POOLS with Column V ertical & W rap Around Covers Fig. I SUPREME POOLS with W rap Around Covers Fig.
DD D D 7 Y our pool must be installed on a solid level surface. After the pool location is selected drive the two end stakes "A" into the ground and mark the center line using string.
Using the “CLEARANCE SIZE” chart on page 6, determine the clearance size for your pool. With the use of the leveling device shown and a shovel start leveling the ground, removing all grass and sharp objects such as sticks and stones. Level area to the lowest spot within the clearance radius.
9 ASSEMBLING THE BO TT OM STRAPS 3 Unpack and assemble the bottom strap s with the buttress bottom plates and brackets as shown using all necessary hardware and tighten securely . Using the chart below determine the quantity of strap assemblies for your pool.
Remove wall from carton. NOTE: the UP arrow on wall. Determine starting point as the filter inlet and outlet holes are at the beginning of the wall. S tarting at the center of a bottom plate insert the bottom edge of the wall into the groove on the bottom rail.
11 CL OSING THE WALL 6 Insert the 1/4" - 20x3/4" truss head screws from inside the pool through the preattached inside closure bar , through inside and outside wall ends, and through outside closure bar . The 1/4" serrated flange nuts are secured to the screws on the out- side of the wall.
12 ASSEMBLE B UTTRESS 7 BUTTRESS TOP PLATE #12 x 1/2” SHEET METAL SCREWS #12 x 1/2” SHEET METAL SCREWS 5/16”-18 x 1/2” HEX HEAD BOLTS 5/16”-18 x 3” HEX HEAD BOLT 5/16”-18 HEX NUT 5/16”.
13 HOLD DO WN SHEET 10 RECHECKING Y OUR W ORK 9 Measure from the last strap to the outer end of the pool. Measurements in both ends should be equal. Also make sure that the sides of the pool between the straps are straight.
14 THR U-THE-WALL SKIMMER 11 IMPORT ANT!! BEFORE CONTINUING WITH THIS STEP YOU MUST KNOW WHICH TYPE OF THROUGH THE W ALL SKIMMER YOU WILL BE USING WITH YOUR POOL Y our pool wall has cutouts to accomodate both standard size skimmers and deluxe wide mouth skimmers.
W all guard is optional. T ape wall guard (plastic sheeting) to pool wall 12" up from ground and smooth out on ground 12" from wall. This will protect your pools metal p arts from chemical reactions with the soil used in the earth mound. Several commercial products can also be used in place of earth mound.
CAUTION YOUR POOL IS DESIGNED TO PROVIDE AN AMPLE SAFETY MARGIN WHEN IT STANDS ON LEVEL GROUND. FOR THIS PURPOSE A SLOPE IN EXCESS OF 2 INCHES IN ANY DIRECTION WALL TO WALL IS CONSIDERED OFF LEVEL YOUR POOL WARRANTY ONLY APPLIES TO POOLS INSTALLED ON LEVEL GROUND AS DEFINED ABOVE.
17 EZ HOOK LINER INST ALLA TION A TTENTION: An 8 inch cove must be placed all around the inside of the pool 1. Clear all sticks and sharp objects from an area near the pool, that is as large as the pool itself. Remove the liner from it s carton and unfold and open the liner .
18 VERTICALS, T OP PLA TES AND RAILS 15 PRE-ASSEMBL Y OF T OP PLA TES* 14 No. 12 x 1/2” Sheet Metal Screw If fencing or decking is to be installed, refer to the deck and fence instructions before installing verticals. The holes indented in the face of the verticals must be on top.
19 No. 12 x 1/2” Sheet Metal Screw Insert two rails into a plate, in the same manner and using the same spacing as you have done on the bottom rail and plate assembly . Push the rails and plate assembly onto the plastic edging leaving the far end in the air .
Y our pool is equipped with (3) three special warning ledges. The (1) one ledge with a large warning on top is to be installed by the entry point into the pool and is not to be obstructed by any object such as your ladder .
21 INST ALLING T OP CO VERS 17 FOLLOW THE INSTRUCTIONS BELOW FOR THE COVERS FOR YOUR P ARTICULAR POOL 4", 6" & 7" DELUXE T OP COVERS These covers don’t require cage nut s or top cover screws.
22 6" & 7" TWO-PIECE FULL CONT OURED COVER Slide inside cover (the cover which will be closest to the inside of the pool) into position and place outside cover onto top of inside cover aligning the holes together with cage nut att ached to the top plate and secure using the 1/4”-20 x 3/4” screw provided.
23 7" AND 9” TWO-PIECE WRAP AROUND COVER AND PEDEST AL Slide the inside cover (the cover which will be closest to the inside of the pool) into position and align the hole in the cover with the cage nut attached to the top plate. Secure using the 1/4”-20 x 3/4” screw provided.
24 WRAP AROUND PEDEST AL 1 - Insert the logo into the pedestal. 2 - Place the pedestal onto the bottom of the vertical and align the holes on the side of the wrap with the holes on the bottom of the vertical. Secure the pedestal using the #12 x 1/2” screws provided.
25 WARNING Four (4) danger labels have been provided for your safety . Apply these labels to the pool where they are easily visible to all persons using the pool. T o do this, simply peel the backing off the label to expose the self stick back and firmly press to a conspicuous and plainly visible surface on the pool.
26 SAFETY TIPS - R ULES AND REGULA TIONS This section is designed to acquaint you with some guidelines as to the safe operation and use of your pool. • Do not dive or jump into your pool. Your pool is approximately 48" or 52” deep. It is not designed for diving or jumping.
27 W ARNING Check all the metal on the pool frame and pool wall for signs of corrosion or deterioration. Remove any corrosion and touch up with paint. Excessive deterioration can lead to failure of the pool structure, which might release large quantities of water that could cause bodily harm and property damage.
A reliable pool water test kit will help to determine the daily chlorine dosage and the acid-alkaline condition of the water. You will find in the test kit two different color comparators.
An important point after buying a device Swim'n Play oval 4ft pool (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Swim'n Play oval 4ft pool yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Swim'n Play oval 4ft pool - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Swim'n Play oval 4ft pool you will learn all the available features of the product, as well as information on its operation. The information that you get Swim'n Play oval 4ft pool will certainly help you make a decision on the purchase.
If you already are a holder of Swim'n Play oval 4ft pool, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Swim'n Play oval 4ft pool.
However, one of the most important roles played by the user manual is to help in solving problems with Swim'n Play oval 4ft pool. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Swim'n Play oval 4ft pool along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
