Instruction/ maintenance manual of the product HL-630 OPC Summit
Go to page of 46
SU MM IT Technologies Cartridge/Machine Reset Guide Version 16 Now with HP & Lexmark co mmon chip error codes! By Mike Josiah Welcome to the 16 th version of our Reset Guide! This guide continues to expand (sometimes on a daily basis), and it will c ontinue to expand for the for-seeable future.
2 Brother HL-1040 OPC Brother Cartridge Part #DR-300 OEM Stated Yield: 20,000 New drum cartridges com e with a clear “Starter Sheet” installed inside th e cartridge. When the cartridge is installed and th e cover closed, the printer will eject the sheet and at the same tim e, reset the drum counter.
3 Brother HL-3260N OPC Brother Cartridge Part #DR-1200 OEM Stated Yield: 60,000 The HL-3260 is Brothers fi rst high speed printer. The drum cartridge comes with three RED sheets and two pieces of tape installed on the cartridg e. There is a possibility that there is developer inside the drum cartridge.
4 Brother HL-7050 Toner Brother Cartridge Part #TN-700 (TN-5500) OEM Stated Yield: 12,000 Located inside the cartridge handle is a small fuse that looks similar to a resist or.
5 Canon NP-6016/C-160 OPC Canon Cartridge Part # F43-4921-700 (NPG-9) OEM Stated Yield: 40,000 The drum unit for these cartridges is rated for 40,000 pages. The machine will show “Replace Drum” at 40,000 pages or when the waste toner section is full.
6 for 5% pages, so it is very possible that you have an empty cartridge with a green wheel showing, or a half full cartridge with a red wheel showing. It all depends on how much toner is used per page. To reset the counter, grasp the color wheel in your right hand, the gear assembly in your left.
7 Goldstar GL-660 (Xerox W.C. Pro 610) 6R00833 Toner, 13R00532 OPC Toner: 5,000 pages, OPC: 10,000 Pages Toner With the Machine on, open the access cover. Press “MENU”, Press “6”, Press “3” Press “CLEAR”, Press “ENTER” OPC With the Machine on, open the access cover.
8 HP Color LaserJet 2600 HP Black # Q6000A, Cyan Q6001A, Magenta Q6003A, Yellow Q6002A OEM Stated Toner Yield: 2500 Black, 2000 Color These cartridges have what HP now calls “Smart Print Technology Chips”. These are the latest in HP chips, they are very small, and contain all new code.
9 HP Color LaserJet 3700 HP Black # Q2670A, Cyan Q2681A, Yellow Q2682A, Magenta Q2683A OEM Stated Toner Yield: 6000 Black, 6000 Color These cartridges have what HP now calls “Smart Chips” Similar to other HP chips, these chips monitor toner usage, Internet supplies ordering, and a new feature, remote troubleshooting.
10 HP Color LaserJet 4500 Transfer Belt HP OPC Part # C4196A OEM Stated Yield: 100,000 Black, 25,000 Color Press the menu button until “RESET MENU” is displayed. Press the “ITE M” button until “NEW TRANSFER KIT, SELECT IF DONE” is displayed.
11 HP Color LaserJet 5500/5550 HP Black # C9730A, Cyan C9731A, Magenta C9733A, Yellow C9732A OEM Stated Yield: 13,000 Black, 12,000 Color These cartridges have what HP now calls “Smart Chips. Similar to the HP-4100, these chips monitor toner usage, Internet su pplies ordering, and a new feature, remote troubles hooting.
12 HP LaserJet 1300 HP Part # Q2613A/X OEM Stated Yield: 2,500/4,000 The HP-1300 uses the second generation black toner cartridge ARD’s. These chips (ARD’s) only monitor toner usage not page counts. Each chip also has its own serial number wh ich in effect gives the cartridge a serial number.
13 set to YES on the cartridge chip. Even after the cartridge is refilled, the printer display will still show “Toner Low” for the supplies status section of the menu. Since these machines do not have a display, only the supplies status page will show “Non HP Toner cartridge”.
14 the menu. The main display will then show “Non HP Toner cartridge”. If the ch ip is removed, the toner low sensors will be disabled, and will not work again until a new HP cartridge is installed. Replacem ent chips are available. Specific 4250 Error Codes : “10.
15 HP LaserJet 9000 HP Part # C4583X OEM Stated Yield: 30,000 Like the HP-4100, the 9000 cartridge also uses a chip. The chip in the 9000 is the same as the 4100 in that they only monitor usage not page counts. Each chip also has its own serial number which in effect gives the cartridge a seri al num ber.
16 Kyocera F-3010 OPC Kyocera OPC Part # DK-2 OEM Stated Yield: 10,000 There is a small black fuse located on the board inside the cartridge. This fuse must be replaced each cycle by un-soldering the ol d and soldering in the new. This fuse is a special 250mA one that should be purchased from your supp lier.
17 Lexmark 4023 (Optra W820/Xerox 4525) Lexmark Cartridge Part # 12B0090 OEM Stated Yield: 5840/5740: 10,000. 5845/5745: 25,000 The “Return” cartridges have an ARD on a small board located inside th e right end cap of the cartridge.
18 E-120 Drum cartridge: With the printer turned on, open the front door. Press and hold the CANCEL button until all the lights be gin to cycle. Close the front door.
19 Lexmark E238 Lexmark Toner Cartridge Part #’s 23800SW, (Return Program), 23820SW (Standard) OEM Toner Stated Yield: 2,000 OEM Drum cartridge 12A8302, Stated drum yield: 30,000 Toner cartridges : The “Return” toner cartridges have an ARD on a small board located inside the right end cap of the cartri dge.
20 Lexmark E321/323 Lexmark Cartridge Part 12A7400/12A7405 (Prebate), 12A7305 (Non Prebate)) OEM Stated Yield: 3,000 (7400), 6000 (7305) The “Return” cartridges have an ARD on a small board located inside th e right end cap of the cartridge.
21 Lexmark T620/622 Lexmark Cartridge Part # 12A6760/12A6860 12A6765/12A6865 OEM Stated Yield: 6760/6860 10,000: 6765/6865 20,000 The “Return” cartridges have an ARD installed on the right side of the cartri dge, (as the cartridge would be inserted into the machine.
22 Lexmark W812 (Fuji-Xerox XP-26) Lexmark Cartridge Part # 14K0050 OEM Stated Yield: 12,000 These cartridges use a chip, but it is not the “Killer type” These chips monitor the “Toner Low” as well as tell the machine the brand of cartridge it is.
23 Minolta PageWorks 1400 Minolta Toner cartridge Part #9J04203 Minolta Drum Cartridge Part # M4519401 OEM Stated Yield Toner: 2,000 OEM Stated Yield OPC: 20,000 Toner Cartridge: These toner cartridges have a chip that must be replaced each cycle. The chip is located on the bottom left side of the cartridge.
24 engine is the Okidata OL-400/800 , but the first actual reset procedure is for the OL-800 series only, followed by other machines that use the same engine but have different reset pr ocedures. Just to make things a little crazier, ther e are also m achines that use different engines, but use the same reset procedure.
25 Okidata C3000 Series Okidata OPC Color Cartridge Part # 42126661, 42126660, 42126659, 42126658 OEM Stated Yield: 15,000 All These machines have a glass fuse that is used to reset the machine. The fuse is located in the ge ar end cap of the cartridge.
26 Okidata OL-400e OPC Okidata OPC Cartridge Part # 56116801 OEM Stated Yield: 20,000 (The procedure for these machines is the same as used for the Okidata OL-1200, OP-20) Turn off the printer While holding the MENU1/MENU2 button down, turn the printer back on.
27 Okidata OL-1200 OPC Okidata OPC Cartridge Part # 56118801 OEM Stated Yield: 30,000 (The procedure for these machines is the same as used for the Okidata OL-400e, and OP-20) Turn off the printer While holding the MENU1/MENU2 button down, turn the printer back on.
28 Okidata OP-14e Okidata OPC Cartridge Part #41331601 (Type 8) OEM Stated Yield: 20,000 (The procedure for these machines is the same as used for the Okidata OP-6e, OL-600e, OP-10e) From the computer the printer is directly hooked up to, enter the Printer Status Monito r.
29 Panasonic KXP-4420 Toner/4420 OPC Panasonic cartridge Part #’s KX-P451, KX- PDM2 OEM Stated Yield: 18,000 Both of these cartridges use a simple 1/16 amp fuse that must be soldered in. The OEM fuse looks like a black transistor. Most of the replacement fuses being sold are in a resistor t ype package.
30 will momentarily press in a lever ins ide the machine and start to reset the coun ter. The tap e will then break releasing the lever finishing the reset procedure. Make sure you use a thin tape and not a packing tape, as it is important that the tape break fairly easily.
31 Samsung CLP-600 Toner/OPC Cartridges Samsung Cart. # CLP-K600A, CLP-C600A, CLP-M600A, CLP-Y600A OEM Stated Yield: 4,000 Black, 4,000 Color These cartridges use a chip that must be replaced each cycle. The chip is located on the rear of the waste hopper.
32 Samsung ML-2150 Toner Cartridges Samsung Cart. # ML-2150D8/XAA OEM Stated Yield: 8,000 These are the first Samsung cartridges to use a chip. The chips can sometimes be used another cycle, b ut to be safe it is best to replace them each cycle. There are different manufacturers using this engine.
33 Samsung SCX-6320Toner/OPC Cartridges Samsung Cart. # SCX-6320D8 (Toner), SCX- 6320R2 (Drum) OEM Stated Yield: 8,000, 18,000 respectively Both of these cartridges use diff erent item s to reset the printer. The toner cartr idge uses a chip th at must be replaced/reset each cycle .
34 pages. These cartridges are designed to be recycled by Sharp authorized dealers. As such, replacement chips are available from authorized S harp dealers, and now generic chips are al so available. Since the chip shuts down the cartridge at 10,000 pages, you can recycle the cartridge 2-3 times with the s ame chip with out any problems .
35 actuator (or flag) is next to the sm all gear). On some cartridges the "flag gear" is now black. It is located to the bottom right of the wh ite gear. Make sure that when you snap the green end cap back on, the notch on the small gear lines up with the tab on the la rge single gear that is on th e cartridge.
36 Sharp AR-152 Developer Sharp Cartridge Part # AR-152DV OEM Stated Yield: 25,000 The developer is rated for 25,000 pages. The default setting on the machine is to keep running even after the 25K pages. That default setting can be set by the dealer to stop at 25K pages.
37 Sharp Cartridge Part # AR-201ND OEM Stated Yield: 30,000 The developer is rated for 30,000 pages. The default setting on the machine is to keep running even after the 30K pages. That default setting can be set by the dealer to stop at 30K pages. It is considered a dealer option.
38 OEM Stated Yield: 20,000 (All) These cartridges do not use any reset procedures at all. According to the Sharp manual, they should be replaced when the copy quality deteriorates. No codes will show on the display to change the cartridge. NOTE: None of these cartridges are interchangeable, they all are slightly different.
39 The display will read PCU DIAG MODE G. Press the MENU key repeatedly until you see COUNTER SET. Press the ENTER key once, and the MENU key twice. The display will read DRM 05000.
40 Turn the power off. Hold down the exposure button, and turn the power on. All the lights except the ready light will come on. Releas e the exposure button. Press the exposure butto n again and hold for 10 seconds, until the three exposure lights come on.
41 TEC LB-1305 OPC OEM Stated Yield: 10,000 (All) There are three major versions of these cartridges. Two use an external counter and one doesn't use one at all. The older style 13 05 has no counter. The label on top of the cartridge has a place to write down the starting page count.
42 type of replacement cartridge that the machine is expecting. 001=113R180/181, 005 = 113R287. If the cartridges your machin e needs is not available, you can change what type of cartridge the machine will accept by doing the following. E nter the diagnostics mode as in a bove.
43 cartridge is changed. A ne w fuse is not needed. However if the machine says change cartridge, the fuse is needed. Since you really have no way to know the state of your customer’s machine, we recommend that the fuse be replaced each cycle.
44 use the correct connector. The 5012 will not work in the 5011 and vice-versa. To tell if you have the correct connector, read the resistance between pin’s 3 & 6.
45 Xerox 5113 Series (5113, 5114, 5614) Xerox Cartridge Part # 113R79 OEM Stated Yield: 18,000 To reset the counter in the 5113 OPC cartridges the connector on the rear of the cartridge m ust be replaced. This will clear the J7 or J8 codes. J7= change copy cartridge, J8 = wrong or bad connector.
46 Xerox 5318/5340 Xerox Cartridge Part # 13R75/13R56 OEM Stated Yield: 25,000 To reset the counter in the 5318 OPC cartridges the connector on the rear of the cartridge m ust be replaced. This will clear the J7 or J8 codes. J7= change copy cartridge, J8 = wrong or bad connector.
An important point after buying a device Summit HL-630 OPC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Summit HL-630 OPC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Summit HL-630 OPC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Summit HL-630 OPC you will learn all the available features of the product, as well as information on its operation. The information that you get Summit HL-630 OPC will certainly help you make a decision on the purchase.
If you already are a holder of Summit HL-630 OPC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Summit HL-630 OPC.
However, one of the most important roles played by the user manual is to help in solving problems with Summit HL-630 OPC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Summit HL-630 OPC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
