Instruction/ maintenance manual of the product LEGACY H7110LS200 Subaru
Go to page of 8
1 INST ALLA TION INSTR UCTIONS SECURITY SYSTEM UPGRADE LEGA CY P/N: H7110LS200 Kit Contents: 1 Security Control Module w/Integral Brack et 1 Starter Interrupt/Horn Relays w/Integral Brack et 1 Horn w/.
2 Figure 1 Figure 2 Figure 3 A. Pre-Installation Notes B. Security Module Installation 1. V ehicle Preparation a. Lower the dri v er’ s side windo w to av oid inadvertently locking the ke ys in the vehicle dur- ing installation. b . Disconnect ne gativ e battery terminal to prev ent accidental shorting of any po wer circuits.
3 Figure 4 Figure 5 Figure 6 4. Lift the center console cov er by carefully pulling outward in areas indicated by arro ws in Figure 4. 5. Remove the six scre ws indicated by the arrows in Figure 5. Do not disconnect any connectors. Pull the unit out just far enough to access the passenger side of the unit.
4 C. Starter Interrupt and Horn Relay Installation 1. Remov e the screw indicated by the arro w in Figure 1 and disengage the two plastic scre ws indicated by arrows in Figure 2, then remov e the dash panel.
5 E. Prior to System T est W ARNING! Do not allo w terminals of radio connectors to come in contact with any metal from vehicle due to +12 v olts being present at these terminals. 1. Reconnect negati ve battery terminal. D. Horn Installation 1. Locate the A T resistor in the engine compartment.
6 G. V alet Mode T est 1. Open the driv er’ s door and then depress and hold the UNLOCK/DISARM button on the remote for more than two seconds and the follo wing should be observed: a. The status indicator (LED) will begin flashing 2x per second indicating that the alarm is in the valet mode.
7 I. Notes on System Operation 1. If the alarm is not deactiv ated within 30 seconds of triggering, the system will automatically reset. 2. The hood is not protected as a part of this system and therefore will not cause a triggering of the alarm when opened unless suff icient force is used in which case the shock sensor will trig- ger the alarm.
8 K. Finishing the Installation 1. Rev erse steps 1 through 10 in section B. Installation Preparation, to reassemble radio, radio trim bezel, cup holder, ashtray , gear shift cover and parking brak e trim. 2. Replace the lower dash panel belo w the steering column.
An important point after buying a device Subaru LEGACY H7110LS200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Subaru LEGACY H7110LS200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Subaru LEGACY H7110LS200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Subaru LEGACY H7110LS200 you will learn all the available features of the product, as well as information on its operation. The information that you get Subaru LEGACY H7110LS200 will certainly help you make a decision on the purchase.
If you already are a holder of Subaru LEGACY H7110LS200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Subaru LEGACY H7110LS200.
However, one of the most important roles played by the user manual is to help in solving problems with Subaru LEGACY H7110LS200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Subaru LEGACY H7110LS200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
