Instruction/ maintenance manual of the product H7110LS200 Subaru
Go to page of 8
1 INST ALLA TION INSTR UCTIONS SECURITY SYSTEM UPGRADE LEGA CY P/N: H7110LS200 Kit Contents: 1 Security Control Module w/Integral Brack et 1 Starter Interrupt/Horn Relays w/Integral Brack et 1 Horn w/.
2 Figure 1 Figure 2 Figure 3 A. Pre-Installation Notes B. Security Module Installation 1. V ehicle Preparation a. Lo wer the driv er’ s side window to a void inadv ertently locking the keys in the v ehicle dur- ing installation. b . Disconnect negati ve battery terminal to pre vent accidental shorting of an y power circuits.
3 Figure 4 Figure 5 Figure 6 4. Lift the center console co ver by carefully pulling outward in areas indicated by arro ws in Figure 4. 5. Remove the six scre ws indicated by the arro ws in Figure 5. Do not disconnect any connectors. Pull the unit out just far enough to access the passenger side of the unit.
4 C. Starter Interrupt and Horn Relay Installation 1. Remov e the screw indicated by the arro w in Figure 1 and disengage the two plastic scre ws indicated by arro ws in Figure 2, then remov e the dash panel.
5 E. Prior to System T est W ARNING! Do not allow terminals of radio connectors to come in contact with any metal from vehicle due to +12 v olts being present at these terminals. 1. Reconnect negati ve battery terminal. D. Horn Installation 1. Locate the A T resistor in the engine compartment.
6 G. V alet Mode T est 1. Open the dri ver’ s door and then depress and hold the UNLOCK/DISARM button on the remote for more than two seconds and the follo wing should be observed: a. The status indicator (LED) will begin flashing 2x per second indicating that the alarm is in the v alet mode.
7 I. Notes on System Operation 1. If the alarm is not deacti vated within 30 seconds of triggering, the system will automatically reset. 2. The hood is not protected as a part of this system and therefore will not cause a triggering of the alarm when opened unless suf ficient force is used in which case the shock sensor will trig- ger the alarm.
8 K. Finishing the Installation 1. Re verse steps 1 through 10 in section B. Installation Preparation, to reassemble radio, radio trim bezel, cup holder , ashtray , gear shift cov er and parking brake trim. 2. Replace the lo wer dash panel below the steering column.
An important point after buying a device Subaru H7110LS200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Subaru H7110LS200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Subaru H7110LS200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Subaru H7110LS200 you will learn all the available features of the product, as well as information on its operation. The information that you get Subaru H7110LS200 will certainly help you make a decision on the purchase.
If you already are a holder of Subaru H7110LS200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Subaru H7110LS200.
However, one of the most important roles played by the user manual is to help in solving problems with Subaru H7110LS200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Subaru H7110LS200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
