Instruction/ maintenance manual of the product H7110FS400 Subaru
Go to page of 8
1 INST ALLA TION INSTR UCTIONS SECURITY SYSTEM UPGRADE FORESTER P/N: H7110FS400 Kit Contents: 1 Security Control Module w/Integral Brack et 1 Starter Interrupt Relay w/Integral Brack et 1 Extension Harness 1m (3 ft.
2 Figure 1 Figure 2 Figure 3 A. Pre-Installation Notes B. Security Module Installation 1. V ehicle Preparation a. Lo wer the driv er’ s side window to a void inadv ertently locking the keys in the v ehicle dur- ing installation. b . Disconnect ne gativ e battery terminal to prev ent accidental shorting of any po wer circuits.
3 Figure 4 Figure 5 Figure 6 5. Remov e and retain for reinstallation, the black M8 bolt indicated by the arro w “ A” in Figure 4. Loosen the M8 bolt indicated by the arro w “B.
4 Figure 7 9 . Remove one plastic scre w and two metal scre ws indicated by the arro ws in Figure 7, then remove the lo wer dash panel by pulling the upper side of the lo wer dash panel tow ard you. 10. Disconnect the four harnesses (two white housings, one bro wn housing and one black housing) on the lo wer dash panel.
5 C. Starter Interrupt Installation 1 . Locate the starter interrupt 6-pin (white housing) connector , which is located next to the right side of the fuse box. See Figure 1. 2. Detach the jumper connector from the f ixing tape, disconnect it from the connector and discard.
6 D. Prior to System T est 1. Reconnect negati ve battery terminal. E. System T est 1. Exit the vehicle and close all doors. 2. Depress the LOCK/ARM button on the remote and the follo wing should be observed: a. All vehicle doors will lock. b . The parking lights will flash once and the horn will chirp once.
7 5. Depress the UNLOCK/DISARM button and the dri ver’ s door should unlock. 6. Open the dri ver’ s door and then depress and hold the UNLOCK/DISARM on the remote for more than 2 seconds and the follo wing should be observed: a.
8 I. Shock Sensor Adjustment-ONL Y IF REQUIRED The factory has preset the sensiti vity of the shock sensor at the time of manufacture. Under normal circumstances the sensitivity should not require an y adjustment and should be left untouched. Ho wev er , in the unlikely e vent that adjustment is required, please follo w the steps outlined below .
An important point after buying a device Subaru H7110FS400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Subaru H7110FS400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Subaru H7110FS400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Subaru H7110FS400 you will learn all the available features of the product, as well as information on its operation. The information that you get Subaru H7110FS400 will certainly help you make a decision on the purchase.
If you already are a holder of Subaru H7110FS400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Subaru H7110FS400.
However, one of the most important roles played by the user manual is to help in solving problems with Subaru H7110FS400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Subaru H7110FS400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
