Instruction/ maintenance manual of the product 542 Sub-Zero
Go to page of 12
II _,! STALLATION STRUCTIONS IIIII III II III I I I I I IiI' '111 SUB-ZERO.
PRI -INSTALLATION INSTRUCTIONS I I I IIIII IIII III I I I IIIII IIIIII I I HI II PREPARATION FOR INSTALLATION Step 1 Prepare the finished rough opening to accept the installation of the Sub-Zero. NOTE: Carefully read the "Pre-lnstallation Specifications" chart below.
i ii I -INSTALLATION TRUCTIONS I ! I I ,REA REPARATION ;tep 2 A/hen units are installed side 3y side, a separating filler strip s recommended. The filler _trip width should be added to he finished rough opening dimension. A filler strip must _lso be used when units are nstalled hinge to hinge.
INSTALLATION INSTRUCTIONS I AwARNING I To reduce the possibility of the unit tipping forward, you must reposition the front levelers to make contact with the floor. You will have to extend these legs when the unit is finally positioned. Step 6 Remove all packing materials and tape.
t '° TALLATION ,.. TRUCTIONS iSTALLATION _WARNING ] ;hut-off power to the wall )utlet. ;tep 9 Jnit is equipped with rollers. )lug into 15 amp grounded )utlet and roll unit into desired )osition under the wood block )r soffit and connect icemaker rater line to unit.
II llllllllll I III IIIIII INSTALLATION INSTRUCTIONS B) With standard Phillips screwdriver, remove door handle on freezer and refrigerator door (the door handles also act as a door trim). The Models 511 and 550 freezer door handle isw on the top of the door and removed in the same manner described above.
I II II I IIIIII I I iF'NSTALLATION .,qSTRUCTIONS -,-]_ ,4) Remove Iouvered grille. Refer to step 7. B) Open the door(s) and attach template provided with panel grille installation kit. The template center hold must be aligned with the grille screw hole and you must fasten from the top down with the screw you removed in step A.
INSTALLATION INSTRUCTIONS r/d" SIDE PANEL INSTALLATION If side panels are being utilized, please check with your installer for installation methods or you may use one of the side panel installation methods shown in Figure 23. Drill 3 holes equal distance apart in vertical section of aluminum frame and install .
i' "'ISTALLATION" ' ,,4STRUCTIONS 2) Using the Loctite on the screws, install all 3 Chicago Screw Posts. 3) Inspect the units for level again. 4) Drill three (3) 3t16" holes (per specs in Figure 24) through both outer trims.
INSTALLATION INSTRUCTIONS IIIIIIIIIII I lU STANDARD HANDLE RECESS SPECIFICATIONS PRODUCT SERVICE =: T 14" ± MODELS 532, 542 AND 561 T 14" ± c I" A _ I------- ,! !i:_i _]_ MODELS 511 AND 550 MODELS 501F ,4 ND 501R Figure 28 MODEL A (WIDTH) B (WIDTH) C (HEIGHT) D E F 532 1715115" 2711116" 6711/16" 385/32 .
LISTAL_LATION ,.4STRUCTIONS _ECOMMENDATIONS :OR RAISED =ANELS _ecause of different door panel Jesigns, routing, recessing, or Jseof optional extended handles nay be necessary for finger "learance when using raised )anels greater than 114" total hickness.
THINK SAFETYt If you are storing or disposing of your old refrigerator, please do it safely. Read the enclosed safety booklet from the Association of Home Appliance Manufacturers. CHILD ENTRAPMENT ACCIDENTS CAN BE TRAGIC! SUB-Z SUB SUB-ZERO FREEZER CO.
An important point after buying a device Sub-Zero 542 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sub-Zero 542 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sub-Zero 542 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sub-Zero 542 you will learn all the available features of the product, as well as information on its operation. The information that you get Sub-Zero 542 will certainly help you make a decision on the purchase.
If you already are a holder of Sub-Zero 542, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sub-Zero 542.
However, one of the most important roles played by the user manual is to help in solving problems with Sub-Zero 542. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sub-Zero 542 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
