Instruction/ maintenance manual of the product Component Speaker Stuttgart
Go to page of 15
COMPONENT SPEAKERS AND CROSSOVERS COMPONENT SPEAKERS AND CROSSOVERS CONTENTS (Click on a topic to view) Congratulations N T - 1 T weeter Mounting Introduction Installation StudioDriver N T - 1 Install.
Congratulations Thank you for selecting STUDIODRIVER components. Manufactured in Stuttgart, Germany , technical innovations and high-tech processes are employed throughout our manufacturing process to help ensure many years of musical enjoyment.
Y our new STUDIODRIVER component set is part of an exciting line of loudspeakers. They are the definitive result of years of research and development, realized by the same engineering team charged wit.
2 STUDIODRIVER N T - 1 MOUNTING P ARAMETERS Mounting Hole for Recess Mount 2.125” Mounting Depth .675” - 1.1” T weeter Diameter 1.775” DESCRIPTION One Inch T itanium Dome T weeter Recommended frequency range 4 kHz - 22 kHz MECHANICAL P ARAMETERS Normal Power Handling 100W rms Fs 1600 Hz Re 3.
3 STUDIODRIVER MR-44 DESCRIPTION Four Inch Aluminum Cone Midwoofer Recommended frequency range 160 Hz - 8 kHz MECHANICAL P ARAMETERS Normal Power Handling 50W rms Fs 78.0 Hz Qms 2.74 V as 2.5 Liters Cms 0.78 mm/N Mms 5.3 grams Rms 0.950 kg/sec Xmax 5 mm Sd 48.
DESCRIPTION Five and one quarter Inch Aluminum Cone Midwoofer Recommended frequency range 90 Hz - 3.5 kHz MECHANICAL P ARAMETERS Normal Power Handling 100W rms Fs 62.0 Hz Qms 4.450 V as 6.9 Liters Cms 0.8 mm/N Mms 8.4 grams Rms 0.73 kg/sec Xmax 5 mm Sd 78.
DESCRIPTION Six and one half Inch Aluminum Cone Midbass Recommended frequency range 70 Hz - 3.5 kHz MECHANICAL P ARAMETERS Normal Power Handling 100W rms Fs 57.0 Hz Qms 4.130 V as 18.6 Liters Cms 0.730 mm/N Mms 18.8 grams Rms 0.93 kg/sec Xmax 5 mm Sd 135.
6 N T - 1 TWEETER ASSEMBL Y The tweeters are equipped with wires and attached connectors. The tweeter wires are designated solid black (-), and black with a white stripe (+). Locate the corresponding spade connectors from the hardware pack and crimp them to the end of your chosen speaker wire.
Configuring the NT -1 T weeter Choose the desired method of mounting the tweeters. The NT -1 tweeters can be surface or recess mounted while allowing rotation of the tweeter within the mount for optimal imaging. Surface Mounting Locate the disk designated "E" in the tweeter assembly drawing.
INST ALLA TION Mounting Considerations for your Midwoofers STUDIODRIVER component speakers are designed to mount into most factory speaker locations with minimum ef fort. The speaker baskets are designed to be a universal fit. When designing your system, a good rule of thumb is to mount the tweeter close to the midrange/midbass speaker .
INST ALLA TION Speaker W iring Locate the hardware pack supplied with your new component set. Inside you will find screws and crimp terminals. The midrange and midbass speakers are each equipped with a small and a large terminal. The large terminal is the positive (+) connection and the small terminal is the negative (-) connection.
10 FN-3 CROSSOVER FN-3 2wayCrossover INPUT WOOFER TWEETER + -- -2dB + 0dB - Connect to the amplifier (+) POSITIVE speaker output Connect to the amplifier (-) NEGA TIVE speaker output Connect to the Mi.
11 FN-6 CROSSOVER FN-6 -2dB 0 dB IN + + + - - -2dB 0 dB - - - - W oofer Midrange T weeter + Connect to the amplifier (+) POSITIVE speaker output Connect to the amplifier (-) NEGA TIVE speaker output C.
ADDITIONAL INFORMA TION NO TE: Abuse and/or Installation Error: STUDIODRIVER defines abuse as, but not limited to, burnt voice coils (blackened, no continuity , melted adhesives, coil separated from the former , etc.
Three-Y ear Limited U.S.A. Warranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. StudioDriver warrants its products to be free from.
An important point after buying a device Stuttgart Component Speaker (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stuttgart Component Speaker yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stuttgart Component Speaker - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stuttgart Component Speaker you will learn all the available features of the product, as well as information on its operation. The information that you get Stuttgart Component Speaker will certainly help you make a decision on the purchase.
If you already are a holder of Stuttgart Component Speaker, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stuttgart Component Speaker.
However, one of the most important roles played by the user manual is to help in solving problems with Stuttgart Component Speaker. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stuttgart Component Speaker along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
