Instruction/ maintenance manual of the product E112 Stoelting
Go to page of 27
Model E1 12 OWNER’S MANUAL Manual No. 513613 Rev .1 October , 2006.
.
This manual provides basic information about the freezer . Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail.
Safety Alert Symbol: This symbol Indicates danger , warning or caution. Attention is required in order to avoid serious personal injury . The message that follows the symbol contains important information about safety .
SECTION DESCRIPTION PAGE 1. INTRODUCTION 1.1 Description ............................................................................................................. 1 1.2 Specifications ...............................................................
LIST OF ILLUSTRA TIONS FIGURE TITLE PAGE 1 - 1 Model E112 Freezer .............................................................................................. 1 1 -2 Freezer Specifications ............................................................
1 Figure 1-2 Freezer Specifications SECTION 1 DESCRIPTION AND SPECIFICA TIONS 1.1 DESCRIPTION The Stoelting E112 counter freezer is gravity fed. The freezer is equipped with fully automatic controls to provide a uniform product. The freezer is designed to operate with almost any type of shake or frozen beverage mix.
2 MODEL E112 COUNTER MODEL GRAVITY FREEZER DIMENSIONS: Freezer: 15-1/4" (33.8 cm) wide x 31-15/16" (81.1 cm) deep x 30-3/8" (77.2 cm) high Crated: 17-1/2" (44.4 cm) wide x 36-1/2" (92.7 cm) deep x 35" (88.9 cm) high WEIGHT: Freezer: 250 lbs.
3 2.1 SAFETY PRECAUTIONS Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. Take notice of all warning labels on the freezer. The labels have been put there to help maintain a safe working environment.
4 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and inspected at the factory. Upon arrival at the final destination, the entire freezer must be checked for any damage which may have occurred during transit. With the method of packaging used, the freezer should arrive in excellent condition.
5 Figure 3-1 Freezer Controls 3.1 OPERATOR’S SAFETY PRECAUTIONS SAFE OPERATION IS NO ACCIDENT; observe these rules: A . Know the freezer. Read and understand the Operating Instructions. B . Notice all warning labels on the freezer. C. Wear proper clothing.
6 B . CLEAN-OFF-ON Switch The CLEAN-OFF-ON switch is used to supply power to the control circuit. When the switch is in the OFF (middle) position, power will not be supplied to the control board or refrigeration system. When the switch is in the ON position, the freezer will operate in the freezing mode.
7 E . After five minutes, place a bucket under the spigot and open spigot to drain sanitizing solution. Place the switch in the OFF (middle) position. Loosen freezer door and allow the freezing cylinder to drain completely. Re-tighten door. F. If using a shake mix, install the mix inlet regulator into hopper (Refer to Figure 3-3).
8 A . Close the spigot and fill the hopper with 2 gallons (8 liters) of tap water. B . Place the switch in the CLEAN position. The auger will start to rotate. C . Allow the water to agitate for approximately 30 seconds. D . Open the spigot to drain the water.
9 L. Remove auger assembly from the freezing cylinder and remove auger blades. M. Remove rear seal and o-ring from auger. N . Remove drain tray, drip tray and drip tray grid. 3.9 CLEANING THE FREEZER PARTS Place all loose parts in a pan or container and take to the wash sink for cleaning.
10 D . Install the two plastic auger blades onto auger. Blades may be attached in any orientation. E . Push auger into freezing cylinder and rotate slowly until auger engages the drive shaft (Refer to Figure 3-9) F. Insert spigot body into front door.
11 regulator is not required. P . Install hopper cover, drain tray, drip tray, and drip tray grid. 3.12 ROUTINE CLEANING To remove spilled or dried mix from the freezer exterior, wash in the direction of the finish with warm soapy water and wipe dry. Do not use highly abrasive materials as they will mar the finish.
12 • MILKSTONE REMOVAL – Complete removal of milkstone. • SANITIZING – FDA-approved no rinse sanitizer for food contact surfaces. Additional Information THE USE OF DELIMERS A delimer is a strong acid that has the ability to dissolve milkstone.
13 2. To remove the condenser filter, remove the thumb screws from under the front panel. Pull down bracket and remove filter. Visually inspect for dirt.
14 This page left intentionally blank.
15 SECTION 4 TROUBLESHOOTING 4.1 MIX LIGHT INDICATORS The following chart shows all possible mix light indicator combinations along with the cause and operation of the freezer. 4.2 TROUBLESHOOTING PR OB LE M POSSIB LE C A U SE R E ME D Y Fre e z e r doe s not run.
16 4.2 TROUBLESHOOTING - CONTINUED P RO BL EM P OS S I BLE CAUS E REM EDY Product i s too s oft . 1. No v ent s pac e f or f re e f low of c ooli ng ai r. 2. A i r t em perat ure entering c ondens er is abov e 100°F. 3. Condens er is di rt y . 4. Cons i s t enc y s et t i ng t oo s of t .
17 SECTION 5 REPLACEMENT P ARTS 5.1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate C .
18 E1 12 REPLACEMENT PARTS.
19 E1 12 REPLACEMENT PARTS P a rt De s cri pti on Qt y 162165 S c rape r B l ade 2 336546 M ol ded Door 1 482019 B l ac k K no b 4 570196 P i n - Door 1 624545 O-Ri ng - S t at o r B ar 1 624644 O-Ri .
.
W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, augers and .
An important point after buying a device Stoelting E112 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stoelting E112 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stoelting E112 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stoelting E112 you will learn all the available features of the product, as well as information on its operation. The information that you get Stoelting E112 will certainly help you make a decision on the purchase.
If you already are a holder of Stoelting E112, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stoelting E112.
However, one of the most important roles played by the user manual is to help in solving problems with Stoelting E112. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stoelting E112 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
