Instruction/ maintenance manual of the product 4WD Stiga
Go to page of 12
STIGA PARK 4WD 92 M 107 M 107 M HD 121 M 110 Combi Pro 125 Combi Pro 8211-054 3-03.
2 125 Combi Pro 1 10/125 Combi Pro 121 M 107 M HD A B C B E F T orx T30 To r x T 3 0 1 10 /125 Combi Pro G H I 1 10/125 Comb i Pro 1 2 1 10/125 Combi Pro 121 M 107 M HD 1 10/125 Combi Pro 10 mm 10 mm .
3 92/107 M A B D B 10 mm 13 mm 13 mm J K L 1 10/125 Combi Pro M 11 13 107 M HD 15 9 92/107 12 92/107 M 14 16 10 92/107.
4 92/107 M 107 M HD 121 M 1/3 92/107 M 121 M 5 mm 1 10/125 Combi Pro 107 M HD 19 21 23 17 20 22 24 18.
5 O 1 10/125 Combi Pro Q 9,8 Nm P 24 Nm 24 Nm 92/107 M 107 M HD 121 M 45 Nm 1 10 Combi Pro O N 107 M HD 24 Nm 125 Combi Pro 27 29 25 28 30 26.
33 ENGLISH EN 1 GENERAL This symbol indicates W ARNING . Seri- ous personal injury and/or damage to property may result if the instructions are not followed car efully . Y ou must read these instructions for use and the machine’ s safety instructions carefully .
34 ENGLISH EN 2.3.3 Rear mounting The cutting deck’ s rear section is secured with the pins in fig. 13. 2.4 Controls, 92/107 M 2.4.1 Cutting heig ht adjustment The cutting height can be adjusted between 30 and 85 mm. The setting can be adjusted to a number of fixed positions using the lever .
35 ENGLISH EN 3.2 Installation of 107 M HD, 121 M 1. Place the cutting deck in position in front of the machine. 2. Install the following components on both wheel axles: • W asher (3:B). • Deck mount (3:C). • W asher (3:B). • Circlip (3:A). 3.
36 ENGLISH EN 3.5.2 Basic setting, 92/107 M, 121 M See fig. 17 and perform basic setting of 92/107 M and 121 M as follows: 1. Place the machine on a level floor . Requirements for floor fl atness: ±1 mm /m. No slope towards a floor drain or similar may occur in front of or behind the machine.
37 ENGLISH EN 5 MAINTENANCE 5.1 Preparation All service and all maintenance must be carried out on a stationary machine with the engine switched off. Prevent the machine from r olling by al- ways applying the parking brake.
38 ENGLISH EN 5.6.1 Separate blades The blades are replaceable. When replacing, both blades on the same blade bar must be replaced to avoid imbalance. T ightening torque: Screws (27:P) - 24 Nm Shear bolts (27:Q) - 9.8 Nm In the event of a collisi on, the shear bolts (27:Q) can break and the blades bend back.
www .stiga.com GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS.
An important point after buying a device Stiga 4WD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stiga 4WD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stiga 4WD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stiga 4WD you will learn all the available features of the product, as well as information on its operation. The information that you get Stiga 4WD will certainly help you make a decision on the purchase.
If you already are a holder of Stiga 4WD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stiga 4WD.
However, one of the most important roles played by the user manual is to help in solving problems with Stiga 4WD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stiga 4WD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
