Instruction/ maintenance manual of the product SM-S220i-DB40 Star Micronics
Go to page of 31
Mobile Prin ter SM-S220 I SERIES Hard w are Ma nu al.
< USA model > F ederal Communications C ommission Radio Frequency Interference Sta tement FCC ID : R49SM-S220 This device complies with P art 15 of the FCC Rules.
T rademark acknowledgments SM-S220I : S tar Micronics Co., L td. Notice • All rights reser ved. Reproduction o f any part of this man ual in any fo rm whatsoe ver , withou t ST AR ’ s exp ress permission is fo rbidden. • e con tents o f this manual are sub jec t to cha nge without no tice.
Caution S ymbol This symbol is placed near the thermal head to indicat e that it may be hot. Never touch the thermal head immediately after the print er has been used. Let the thermal head cool for a f ew minutes befor e touching it. This symbol is placed near the thermal head to indicat e that it is easily damaged.
n U sing the Prin ter P Some semicond uctors can be damaged b y static electricity . B e sure to t urn o the print er when inser ting or r emoving the ba ttery p ack. P Do not dro p the print er or hit it a gainst a har d object. P Do not o pen the printer co ver while the printer is p rinting.
n Oper a ting Enviro nment f or the Prin ter Before actually unpacking the printer , you should take a f ew minutes to think about where y ou plan to use it. Remember the follo wing points when doing this. P Do not use the p rinter in an en vironm ent in which it will be subject to stro ng shaking while it is prin ting.
T able of C ont ents 1. Pr oduc t Overview ............................................................................ 1 1.1 P rinter & Ac cessories .................................................................................................
- 1 - iP od, iPhone and iP ad compatibility list Made for • iP od touch (5th generation) • iP od touch (4th generation) • iPhone 5 • iPhone 4S • iPhone 4 • iP ad (4rd generation) • iP ad (3rd generation) • iP ad 2 • iP ad • iP ad mini Note: as of December .
- 2 - 1.1 Printer & A cc essories The printer is packaged with the following acc essories. If any of these accessories is broken or missing , please contact the dealer that you bought the pr oduct. u The optional items for this print er are listed below .
- 3 - 1.2 Ex ternal Appearanc e and P ar t Names COM1(Serial 6P) For connecting to the host device For connecting to a PIN pad or RFID module COM2(NFC/PED 8P) Cover Open Lever ERROR Lamp POWER Lamp FE.
- 4 - 2. Setup 2.1 Batter y P ack 2.1.1 Inser ting into the Prin ter 1. Make sure that the printer has been turned o bef ore you insert or remove the ba tter y pack. 2. I nser t the battery pack into the back of the printer as in the gur e shown below , following the direc - tion of the arrow .
- 5 - Notes about the Batter y Pack u General Battery Characteristics • The battery is a consumable and its per formance ov er time will gradually decrease . • While not in use, the batt er y will slowly discharge itself . Pr epare a battery pack that has been charged relativ ely recently (1 to 2 da ys earlier).
- 6 - < F or U .S.A. and Canada > Lithium-Ionbatteriesarer ec yclable . Y oucanhelppreserveourenvir onmentbyre - turning your used rechar geable batteries to the collection and recycling location nearest you .
- 7 - 2.2 Bluetooth 2.2.1 Connection 1. When you turn on the printer , it is ready to pair with another Bluetooth device . 2. If necessar y , enter the f ollowing information into the t erminal that you are using . PIN: 1234 (default) Device name: Star M icronics (default) F or secur ity purposes, we r ecommend that you change the PIN.
- 8 - 2.2.2 Aut o Connection F unc tion (only for iOS *1 ) When the Bluetooth connection with your iOS devic e (*2 is disconnected, it is r equired to establish a connection by tapping the printer you wan t to use on the Bluetooth setting screen.
- 9 - 2.3 Loading P aper Refer to chapter 4, “Paper ” (page 20), to select roll paper that conf orms to the specications. 1. T ur n on the printer . 2. Put y our nger on the lever for opening the co ver , and then open and raise the printer cov er .
- 10 - 4. Press down on both sides of the print er cover to close it rmly . When y ou close the printer cov er , make sure that it is closed on both sides. 5. Use the tear bar to cut the extra paper . CA UTION When the paper is jammed, be sure to open the print er cov er before removing the jammed paper .
- 1 1 - 2.4 M emor y Swit ch Settings Change the Memor y switch by this operation. (Ref er to “Memor y Switch Setting T able ”). MODE button : Changing OPTION status . FEED button : Chang ing PRINTER MODE status * Example: When you w ant to switch from the default settings t o the following settings.
- 12 - After you hav e congured all of the settings , press and release FEED and MODE at the same time . The new settings will be printed. If the settings were not c ongured correctly , fol low the above pr ocedure to c ongure the settings again.
- 13 - Print er Mode Setting Display 1 Communication P ort v 1) Bluetooth(iOS) * Bluetooth(iAP) Bluetooth Bluetooth Mode RS-232C U ART Mode 2 Baud Rate 9600 bps 9600 BPS 38400 bps 38400 BPS 115200 bps.
- 14 - v 1 ) Communication mode It is possible to change the communication mode setting between Bluetooth and serial. Please see below for details t o select the proper communication mode for y our application. Bluetooth (iOS): The display sho ws [Bluetooth(iAP)].
- 15 - 2.5 B elt Clip 2.5.1 Attaching t o the Printer F ollow the procedur e below to attach the belt clip to the print er . 1. Make sure that you ar e attaching the belt clip in the right orientation, then screw the screw tha t comes with the belt clip into the desig nated screw hole to attach the belt clip t o the printer .
- 16 - 3. Prin ter F eatures 3.1 Contr ol Panel 3.1.1 Buttons 1) FEED button: When the printer is on, you can press FEED t o feed the paper . 2) MODE button: Y ou can change the communication mode and print settings by conguring the printer ’ s mode settings.
- 17 - Printer S tatus Action LED LC D Buzzer POWER (Green) ERROR (Red) Printer Initialization(P ower On) Flickering Flickering Display : [ Bluetooth Mode ] Back Light : Flickering during initializati.
- 18 - 3.2 Self T est Y oucanuseaselftesttochecktheprinter ’ ssettings. Before y ou star t the self test, make sure that r oll paper has been properly loaded into the printer . 3.2.1 Self T est Pr ocedure 1) T urn on the power while holding down FEED .
- 19 - 3.3 I nstruction for Aut o P ower Do wn(Sleep) Mode The printer in the P ower Do wn(Sleep) Mode will recover t o the Print Ready Mode when receiving commands or button operations . Howev er , pr int data r eceived while shifting from the Sleep Mode to the print Ready Mode (for ap - pro x.
- 20 - 4.2 Recommended Paper ( Common thermal roll paper) Manufacturer Product Name Mitsubishi Paper Mills Limited P220AG Oji Paper C o., L td. PD450 APPLETON Alpha 800-2.4 KANZAKI (Oji P aper USA) P-350 4.3 Printing Range 4. P aper 4.1 Paper Specications T ype : Thermal Paper P aper width : 57.
- 21 - 5. G ener al Specic ations Item Specications Printing method Dir ect line thermal pr inting Characters per line Maximum 42 cpl Character size Alphanumeric characters: 12 X 24 dots, 9 X 24.
- 22 - n External Specications External dimensions: Appro ximately 82 mm ( W ) × 140 mm (D) × 47 mm (H) W eight: 289g(printer+batterypack).
- 23 - Appli cation of Counci l Di recti ve(s ) R& T TE 1999/5/EC of 9 M ar. 1999 Standard( s) to w hich C onf orm ity i s Decl ared Radi o ： EN 300 328 V1.
URL : http://www .starmicronics.com/s upport/ Rev . 1.1.
An important point after buying a device Star Micronics SM-S220i-DB40 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Star Micronics SM-S220i-DB40 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Star Micronics SM-S220i-DB40 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Star Micronics SM-S220i-DB40 you will learn all the available features of the product, as well as information on its operation. The information that you get Star Micronics SM-S220i-DB40 will certainly help you make a decision on the purchase.
If you already are a holder of Star Micronics SM-S220i-DB40, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Star Micronics SM-S220i-DB40.
However, one of the most important roles played by the user manual is to help in solving problems with Star Micronics SM-S220i-DB40. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Star Micronics SM-S220i-DB40 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
