Instruction/ maintenance manual of the product IP16 Stanley Black & Decker
Go to page of 16
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 10413 9/2014 V er . 3 USER MANUAL Safety , Operation and Maintenance IP16 HYDRAULIC INTENSIFIER.
.
IP16 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► IP16 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
IP16 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► IP16 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
IP16 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► IP16 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
IP16 User Manual ◄ 9 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
10 ► IP16 User Manual NOTE: High-pressure couplings must be used for the high- pressure connections at the output side of the in- tensier . 4. Connect the tool to be used (stretcher , cutter , etc,) to the unit. Refer to the applicable Operation Manual for detailed connection procedures.
IP16 User Manual ◄ 1 1 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
12 ► IP16 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the intensier , always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the intensier as listed in the table.
IP16 User Manual ◄ 13 Output Pressure ............................................................................................................................ 10,000 psi/700 Bar Input Pressure ....................................................
14 ► IP16 User Manual IP16 P ARTS ILLUSTRA TION.
IP16 User Manual ◄ 15 ITEM P ART NO. QTY DESCRIPTION 09853 1 MOTOR ASSY (INCL ITEMS 1–15) 1 09868 1 MOTOR HOUSING (INCL ITEM 2) 2 05207 1 BUSHING 3 13996 2 O-RING 1/2 × 1 1/18 × 3/32 * 4 01257 1.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker IP16 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker IP16 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker IP16 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker IP16 you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker IP16 will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker IP16, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker IP16.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker IP16. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker IP16 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
