EN
Speed Queen logo
Official user manual

Speed Queen TMB795C

31 pages·1.1 MB·Clothes Dryer·PDF·ENDEFRITNLJA
Speed Queen TMB795C
Table of Contents 80 sections Drying Tumblers · occupants. – Immediately call your gas supplier · FOR YOUR SAFETY · W440R1 · … ShowHide
Drying Tumblersp.1occupants. – Immediately call your gas supplierp.3FOR YOUR SAFETYp.3W440R1p.3Table of Contentsp.4Installation/Operation Supplement Introductionp.5Model Identificationp.5Wiring Diagramp.5Serial Plate Locationp.5Safety Informationp.6Save These Instructionsp.6Important Safety Instructionsp.6Installationp.8Specifications and Dimensionsp.8Cabinet Dimensionsp.9Horizontal Exhaust Outlet Locationsp.10Gas Connection Locationsp.11Electrical Connection Locationsp.12B Bp.12TMB813N GAS AND STEAM ELECTRICp.12Steam Connection Locationsp.13Position and Level the Tumblerp.14Water Connectionsp.15Electrical Requirementsp.16Auxiliary Alarmp.16European Gasp.16Gas Requirementsp.16Natural Gas and Liquefied Petroleump.16General Informationp.17DK/NO/ SE/FI/CZ/ EE/LV/LT/p.17SI/SKp.17DE**p.17NLp.17N/Ap.17BE/FR*p.17GB/IE/PT/ ES/IT/GR/p.17LU/CHp.17AT**p.17HUp.18PLp.18Exhaust Requirementsp.19Ventingp.19Make-Up Airp.19CAUTIONp.20Grounding Instructionsp.20Steam Requirementsp.21Thermal Oil Prepp.21Installation/Operation Supplement Operationp.23Emergency Stop Buttonp.23Operating Instructionsp.23Step 1: Clean Lint Screen/Compartmentp.23Step 2: Load Laundryp.23Step 3: Determine Control Type and Temperature Settingp.23Step 4: Remove Laundryp.23Control Instructionsp.24Electromechanical Coin Controlp.24PUSHp.24TO STARTp.24TEMPERATUREp.24HIGHp.24LOWp.24INSERT QUARTER TURN KNOBp.24Manual Timer Controlp.25HEATp.255 COOL DOWNp.25Dual Digital Timer Controlp.26Electronic OPL Micro Controlp.27STARTp.27STOP/RESETp.27ON / SELECTp.27MEDIUMp.27MED LOWp.27NO HEATp.27REVERSINGp.27Single Drop Controlp.29MDC Coin and Card Controlp.29TMBp.29TMB1492N TMB1963Np.29Ignition Control Operationp.30Diagnostic LED (DGN LED) / Error Codesp.30
Page 1 of the Speed Queen TMB795C user manual — Drying Tumblers
Page 1 · click to enlarge
Page 1

Drying Tumblers

50 Pound Capacity 75 Pound Capacity Refer to Page 3 for Model Identification

Speed Queen TMB795C — Drying Tumblers diagram (page 1)
Fig. 1 · Drying Tumblers

Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.)

Part No. M414884R10

February 2008

Page 2 of the Speed Queen TMB795C user manual — Drying Tumblers
Page 2 · click to enlarge
Page 2
Page 2 of the Speed Queen TMB795C user manual — Drying Tumblers
Page 3 of the Speed Queen TMB795C user manual — W440R1
Page 3 · click to enlarge
Page 3

Installation must conform with local codes.

  • To reduce the risk of fire, electric shock, serious injury or death to persons when using the tumbler unit, follow these basic precautions:
  • Read all instructions before using tumbler.
  • DO NOT tamper with controls.
  • DO NOT bypass any safety devices.
  • Always follow the fabric care instructions supplied by the garment manufacturer.
  • Remove laundry immediately after the tumbler stops.
  • DO NOT reach into tumbler if cylinder is revolving.

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.

  • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
  • WHAT TO DO IF YOU SMELL GAS: – Do not try to light any appliance. – Do not touch any electrical switch; do

not use any phone in your building. – Clear the room, building or area of all

occupants. – Immediately call your gas supplier

  • To avoid creating any flammable vapors which may explode, ignite or cause corrosive damage, DO NOT dry the following materials:
  • Articles that have been cleaned in, soaked in, washed in or spotted with gasoline, dry-cleaning solvents or other flammable/explosive substances.
  • Plastics or articles containing foam rubber or similarly textured rubberlike materials.
  • Articles that have traces of flammable substances like cooking oil, machine oil, flammable chemicals or thinner.
  • Articles containing wax or cleaning chemicals.
  • Fiberglass curtains or draperies (unless the label says it can be done).

from a neighbor’s phone. Follow the gas supplier’s instructions. – If you cannot reach your gas supplier,

call the fire department. • Installation and service must be performed by a qualified installer, service agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

W440R1

M414884 (EN) 1 © Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 4 of the Speed Queen TMB795C user manual — Table of Contents
Page 4 · Contents
Contents

Contents

Drying Tumblersp.1occupants. – Immediately call your gas supplierp.3FOR YOUR SAFETYp.3W440R1p.3Table of Contentsp.4Installation/Operation Supplement Introductionp.5Model Identificationp.5Wiring Diagramp.5Serial Plate Locationp.5Safety Informationp.6Save These Instructionsp.6Important Safety Instructionsp.6Installationp.8Specifications and Dimensionsp.8Cabinet Dimensionsp.9Horizontal Exhaust Outlet Locationsp.10Gas Connection Locationsp.11Electrical Connection Locationsp.12B Bp.12TMB813N GAS AND STEAM ELECTRICp.12Steam Connection Locationsp.13Position and Level the Tumblerp.14Water Connectionsp.15Electrical Requirementsp.16Auxiliary Alarmp.16European Gasp.16Gas Requirementsp.16Natural Gas and Liquefied Petroleump.16General Informationp.17DK/NO/ SE/FI/CZ/ EE/LV/LT/p.17SI/SKp.17DE**p.17NLp.17N/Ap.17BE/FR*p.17GB/IE/PT/ ES/IT/GR/p.17LU/CHp.17AT**p.17HUp.18PLp.18Exhaust Requirementsp.19Ventingp.19Make-Up Airp.19CAUTIONp.20Grounding Instructionsp.20Steam Requirementsp.21Thermal Oil Prepp.21Installation/Operation Supplement Operationp.23Emergency Stop Buttonp.23Operating Instructionsp.23Step 1: Clean Lint Screen/Compartmentp.23Step 2: Load Laundryp.23Step 3: Determine Control Type and Temperature Settingp.23Step 4: Remove Laundryp.23Control Instructionsp.24Electromechanical Coin Controlp.24PUSHp.24TO STARTp.24TEMPERATUREp.24HIGHp.24LOWp.24INSERT QUARTER TURN KNOBp.24Manual Timer Controlp.25HEATp.255 COOL DOWNp.25Dual Digital Timer Controlp.26Electronic OPL Micro Controlp.27STARTp.27STOP/RESETp.27ON / SELECTp.27MEDIUMp.27MED LOWp.27NO HEATp.27REVERSINGp.27Single Drop Controlp.29MDC Coin and Card Controlp.29TMBp.29TMB1492N TMB1963Np.29Ignition Control Operationp.30Diagnostic LED (DGN LED) / Error Codesp.30
Page 5 of the Speed Queen TMB795C user manual — Wiring Diagram
Page 5 · click to enlarge
Page 5

Installation/Operation Supplement Introduction

Model Identification

Information in this manual is applicable to these models.

GasSteam/Thermal OilElectric 50 PoundGU050L LU050N GU050N PU050L HU050L PU050N HU050N SU050L KU050L SU050N KU050N UU050L LU050L UU050NGU050S LU050T GU050T PU050S HU050S PU050T HU050T SU050S KU050S SU050T KU050T UU050S LU050S UU050TGU050E HU050E KU050E LU050E PU050E SU050E UU050E 75 PoundGU075L LU075N GU075N PU075L HU075L PU075N HU075N SU075L KU075L SU075N KU075N UU075L LU075L UU075NGU075S PU075S GU075T PU075T HU075S SU075S HU075T SU075T KU075S UU075S KU075T UU075T LU075S YU075S LU075T YU075TGU075E HU075E KU075E LU075E PU075E SU075E UU075E YU075E
Speed Queen TMB795C — Model Identification diagram (page 5)
Fig. 2 · Model Identification

Includes models with control suffixes:

BC – basic electronic, coin CD – rotary coin drop RM – reversing OPL Micro

BG – basic electronic, OPL mode CX – prep for coin RQ – reversing dual digital timer

BL – basic electronic, central pay CY – prep for card RT – reversing manual timer

BU – basic electronic, prep card - open MT – manual timer SD – single drop

BX – basic electronic, prep for coin OM –OPL Micro SX – single drop, prep for coin

BY – basic electronic, prep for card QT – dual digital timer

Wiring Diagram

Serial Plate Location

The wiring diagram is located in the junction or contactor box.

Speed Queen TMB795C — Wiring Diagram diagram (page 5)
Fig. 3 · Wiring Diagram

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 3 M414884 (EN)

Page 6 of the Speed Queen TMB795C user manual — Save These Instructions
Page 6 · click to enlarge
Page 6

Safety Information

Save These Instructions

Important Safety Instructions

13. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt.
14. The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel.

Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to working in and around AC inverter drive.

15. If not installed, operated and maintained in accordance with the manufacturer’s instructions or if there is damage to or mishandling of this product’s components, use of this product could expose you to substances in the fuel or from fuel combustion which can cause death or serious illness and which are known to the State of California to cause cancer, birth defects or other reproductive harm.
1. Read all instructions before using the tumbler.
2. Refer to the GROUNDING INSTRUCTIONS for the proper grounding of the tumbler.
3. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
16. Tumbler will not operate with the loading door open. DO NOT bypass the door safety switch to permit the tumbler to operate with the door open. The tumbler will stop tumbling when the door is opened. Do not use the tumbler if it does not stop tumbling when the door is opened or starts tumbling without pressing or turning the START mechanism. Remove the tumbler from use and call for service.
4. Do not allow children to play on or in the tumbler. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
5. Before the tumbler is removed from service or discarded, remove the door to the drying compartment and the door to the lint compartment.
17. Tumbler will not operate with lint panel open. DO NOT bypass lint panel safety switch to permit the tumbler to operate with the lint panel open.
6. Do not reach into the tumbler if the cylinder is revolving.
18. Do not put articles soiled with vegetable or cooking oil in the tumbler, as these oils may not be removed during washing. Due to the remaining oil, the fabric may catch on fire by itself.
7. Do not install or store the tumbler where it will be exposed to water and/or weather.
19. To reduce the risk of fire, DO NOT put clothes which have traces of any flammable substances such as machine oil, flammable chemicals, thinner, etc. or anything containing wax or chemicals such as in mops and cleaning cloths, or anything dry-cleaned at home with dry-cleaning solvent in the tumbler.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the tumbler, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
20. Use the tumbler only for its intended purpose, drying fabrics.
10. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
21. ALWAYS disconnect and lockout the electrical power to the tumbler before servicing. Disconnect power by shutting off appropriate breaker or fuse.
11. To reduce the risk of fire, DO NOT DRY plastics or articles containing foam rubber or similarly textured rubberlike materials.
12. Always clean the lint filter daily.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT M414884 (EN) 4

Page 7 of the Speed Queen TMB795C user manual — Safety Information
Page 7 · click to enlarge
Page 7
22. Install this tumbler according to the INSTALLATION INSTRUCTIONS . All connections for electrical power, grounding, and gas supply must comply with local codes and be made by licensed personnel when required.
28. DO NOT operate the tumbler if it is smoking, grinding, has missing or broken parts.
29. DO NOT bypass any safety devices.
30. Solvent vapors from dry-cleaning machines create acids when drawn through the heater of the drying unit. These acids are corrosive to the tumbler as well as to the laundry load being dried. Be sure make-up air is free of solvent vapors.
23. Remove laundry immediately after tumbler stops.
24. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of reach of children at all times (preferably in a locked cabinet).
31. Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.
25. Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.
26. Always follow the fabric care instructions supplied by the garment manufacturer.

To reduce the risk of serious injury, install lockable door(s) to prevent public access to rear of tumblers.

27. Never operate the tumbler with any guards and/or panels removed.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 8 of the Speed Queen TMB795C user manual — Specifications and Dimensions
Page 8 · click to enlarge
Page 8

Installation

Specifications and Dimensions

Specifications50 Pound75 Pound Noise level measured during operation at operator position of 1 meter (3.3 feet) in front of machine and 1.6 meters (5.2 feet) from floor.63 dBA69 dBA Net Weight (approximate): kg (lbs.)247 (545)279 (615) Cylinder Size: mm (in.)940 x 762 (37 x 30)940 x 914 (37 x 36) Cylinder Capacity (dry weight): kg (lbs.)22.7 (50)34 (75) Air Outlet Diameter: mm (in.)203 (8)203 (8) Maximum Static Back Pressure: mbar (inches W.C.)1.3 (0.5)1.3 (0.5) Maximum Airflow: l/sec. (C.F.M.)354 (750)Gas/Steam 50 Hz 354 (750) Gas/Steam 60 Hz 434 (920) Electric 354 (750) Motor Horsepower: Nonreversing Reversing Fan Cylinder1/2 1/3 1/33/4 1/3 1/3 Gas Models Gas Connection1/2 in. NPT1/2 in. NPT Gas Burner Rating: Mj/hr (Btu/hr)126.6 (120,000)174.1 (165,000) Electric Models Heating Element Rating: Kilowatts (kW)21 kW (240 V/50 Hertz) 30 kW (other voltages)30 kW Steam Models Steam Connection3/4 in. NPT3/4 in. NPT Steam Coil Rating: Boiler Horsepower (Btu/hr)5.1 (177,500)6.1 (210,300)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT M414884 (EN) 6

Page 9 of the Speed Queen TMB795C user manual — Cabinet Dimensions
Page 9 · click to enlarge
Page 9

Cabinet Dimensions

Speed Queen TMB795C — Cabinet Dimensions diagram (page 9)
Fig. 4 · Cabinet Dimensions
ModelsABCDEFG 050 Gas and Electric****** 781 mm (30.75 in.)730 mm (28.75 in.)717 mm (28.25 in.)860 mm (33.87 in.)1194 mm (47 in.)1946 mm (76.625 in.)981 mm (38.625 in.)838 mm 7 (33 in.) (249 mm 9.5 in.) 050 Steam781 mm (30.75 in.)730 mm (28.75 in.)717 mm (28.25 in.)860 mm (33.87 in.)1194 mm (47 in.)2032 mm (80 in.)981 mm (38.625 in.)838 mm 7 (33 in.) (249 mm 9.5 in.) 075 Gas and Electric781 mm (30.75 in.)730 mm (28.75 in.)717 mm (28.25 in.)860 mm (33.87 in.)1346 mm (53 in.)1946 mm (76.625 in.)981 mm (38.625 in.)838 mm 9 (33 in.) (302 mm 5.5 in.) 075 Steam781 mm (30.75 in.)730 mm (28.75 in.)717 mm (28.25 in.)860 mm (33.87 in.)1346 mm (53 in.)2032 mm (80 in.)981 mm (38.625 in.)838 mm 9 (33 in.) (302 mm 5.5 in.)

* H, S and U models prior to Serial No 0308001307 and all other models. ** H, S and U models after Serial No. 0308001307.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 10 of the Speed Queen TMB795C user manual — Horizontal Exhaust Outlet Locations
Page 10 · click to enlarge
Page 10

Horizontal Exhaust Outlet Locations

B

A

ModelsABC 050/075137 mm (5.375 in.)203 mm (8 in.)340 mm (13.375 in.)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 11 of the Speed Queen TMB795C user manual — Gas Connection Locations
Page 11 · click to enlarge
Page 11

Gas Connection Locations

A

B

ModelsDiameterAB 0501/2 in. NPT394 mm (15.5 in.)1670 mm (65.75 in.) 0751/2 in. NPT400 mm (15.75 in.)1670 mm (65.75 in.)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 12 of the Speed Queen TMB795C user manual — Electrical Connection Locations
Page 12 · click to enlarge
Page 12

Electrical Connection Locations

A

A

B B

TMB813N GAS AND STEAM ELECTRIC

ModelsAB Gas and Steam241 mm (9.5 in.)1613 mm (63.5 in.) Electric483 mm (19 in.)1626 mm (64 in.)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 13 of the Speed Queen TMB795C user manual — Steam Connection Locations
Page 13 · click to enlarge
Page 13

Steam Connection Locations

A

B

D

Models Diameter A B C D

050/075 3/4 in. NPT 387 mm (15.25 in.)

1848 mm (72.75 in.)

190 mm (7.5 in.)

1645 mm (64.75 in.)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 14 of the Speed Queen TMB795C user manual — Position and Level the Tumbler
Page 14 · click to enlarge
Page 14

Position and Level the Tumbler

To reduce the risk of severe injury, clearance of tumbler cabinet from combustible construction must conform to the minimum clearances.

TMB2131N NOTE: Shaded areas indicate adjacent structure.

1 13 mm (0.5 in.) recommended between machines for removal or installation 2 Allow 51-102 mm (2-4 in.) opening at top of machine to aid in removal or installation. A removable trim piece may be used to conceal the opening; zero clearance allowed for trim. 3 102 mm (4 in.) maximum header thickness 4 305 mm (12 in.) minimum clearance permitted for remainder 5 Guard 6 Provision for make-up air 7 610 mm (24 in.) minimum, 914 mm (36 in.) recommended for maintenance purposes 8 6 mm (0.25 in.) recommended for removal or installation purposes, zero clearance allowed

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 15 of the Speed Queen TMB795C user manual — Water Connections
Page 15 · click to enlarge
Page 15

Fire Suppression System G, H, K, S and U Models Only Water Requirements

Water Connections

Speed Queen TMB795C — Water Connections diagram (page 15)
Fig. 5 · Water Connections

Connection point to the electric water solenoid valve is a 19 mm (3/4 inch) hose. The fire suppression system equipped tumbler must be supplied with a minimum water pipe size of 12,7 mm (1/2 inch) and be provided with a minimum of 138 kPa (20 psi) and a maximum of 827 kPa (120 psi) of pressure at all times. Flowrate must be no less than, but approximately 57 liters (15 gallons) per minute.

TMB2008N 1 Lock 2 Hose Couplings 3 Y Valve 4 Inlet Hoses 5 Opening for Auxiliary Alarm Cable

Part No. 20617 Inlet hose 2.44 m (8 feet) Part No. 20618 Inlet hose 3.05 m (10 feet)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 16 of the Speed Queen TMB795C user manual — European Gas
Page 16 · click to enlarge
Page 16

Electrical Requirements

Electrical power must be provided to tumbler at all times. The fire suppression system will be inoperative if the main electrical power supply is disconnected.

No independent external power source or supply connection is necessary. Power to operate the 24 Volt fire suppression system is from the rear junction/ contactor box.

Auxiliary Alarm

During tumbler installation, you have the option to connect a separate alarm system to this auxiliary output. Use of the auxiliary output is not required for the fire suppression system to operate, but may be used for additional protection.

To reduce the risk of fire or explosion, if the tumbler is to be connected to Liquefied Petroleum (L.P.) gas, a vent to the outdoors must be provided in the room where the tumbler is installed.

European Gas

Gas Requirements

Natural Gas and Liquefied Petroleum

  • To reduce the risk of electric shock, fire, explosion, serious injury or death:
  • Disconnect electric power to the tumbler before servicing.
  • Close gas shut-off valve to gas tumbler before servicing.
  • Close steam valve to steam tumbler before servicing.
  • Never start the tumbler with any guards/ panels removed.
  • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded.

To reduce the risk of fire or explosion, DO NOT CONNECT THE GAS LINE TO THE TUMBLER IF THE GAS SERVICE IS NOT THE SAME AS THAT SPECIFIED ON THE TUMBLER SERIAL PLATE! It will first be necessary to convert the gas burner orifice and gas valve. Appropriate conversion kits are available.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 17 of the Speed Queen TMB795C user manual — AT**
Page 17 · click to enlarge
Page 17

General Information

Models are built in two different configurations:

  • Natural Gas – regulated/governor

This information is to be used when installing gas tumblers in countries, and/or on gases, different than the machine’s factory configuration. Tumblers are supplied from the factory for operation on Natural Gas or L.P. Gas in the countries of GB/IE/PT/ES/IT/GR/ LU/CH. To install machines in any other country, or on any other gas, requires some level of modification.

  • Liquefied Petroleum (L.P.) Gas – not regulated/ no governor

Machines configured for Natural Gas (regulator/ governor) may be converted to L.P. Gas (not regulated/ no governor) with block-open kit, Part No. M400763.

Serial plates are configured for GB/IE/PT/ES/IT/GR/ LU/CH.

Code Gas Type Group

Orifice Part No.

DK/NO/ SE/FI/CZ/ EE/LV/LT/

Natural Gas H 20 8.9 050 075 3.7 3.6 2 3 M401000 M401014

L.P. Gas B/P 30 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

SI/SK

Natural Gas E 20 8.9 050 075 3.7 3.6 2 3 M401000 M401014

LL 25 12.6 050 075 3.7 3.6 2 3 M401000 M401014

DE**

L.P. Gas B/P 30 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

B/P 50 28.5 050 075 2.1 2.0 2 3 M401003 M400999

Natural Gas L 25 12.6 050 075 3.7 3.6 2 3 M401000 M401014

NL

L.P. Gas B/P 30 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

Natural Gas E+ 20/25 No Governor 050 075 3.0 2.9 2 3 M401017

N/A

BE/FR*

L.P. Gas + 28/37 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

Natural Gas H 20 8.9 050 075 3.7 3.6 2 3 M401000 M401014

GB/IE/PT/ ES/IT/GR/

L.P. Gas + 28/37 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

LU/CH

Natural Gas H 20 8.9 050 075 3.7 3.6 2 3 M401000 M401014

AT**

L.P. Gas B/P 50 28.5 050 075 2.1 2.0 2 3 M401003 M400999

CY/IS/MT L.P. Gas B/P 30 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Show 12 more labels / short text on this page
Burner · Supply Pressure, · Burner · Country · Orifice Pressure, · Capacity/ · Diameter, · mm Quantity · Model · mbar · mbar · Table 1
Page 18 of the Speed Queen TMB795C user manual — PL
Page 18 · click to enlarge
Page 18

Code Gas Type Group

Orifice Part No.

Natural Gas H 25 8.9 050 075 3.7 3.6 2 3 M401000 M401014

HU

L.P. Gas B/P 30 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

Natural Gas H 20 8.9 050 075 3.7 3.6 2 3 M401000 M401014

PL

L.P. Gas 3P 37 No Governor 050 075 2.1 2.0 2 3 M401003 M400999

Burner orifice information at 0-600 meters (0-2000 feet) altitude. N/A = Part no longer available.

* For Natural Gas, Group E+ applications, convert using L.P. Gas model and replace burner orifices. ** For L.P. Gas, Group B/P with 50 mbar supply pressure, convert using Natural Gas model, M411334 regulator spring kit and burner orifices.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Show 12 more labels / short text on this page
Burner · Supply Pressure, · Burner · Country · Orifice Pressure, · Capacity/ · Diameter, · mm Quantity · Model · mbar · mbar · Table 1
Page 19 of the Speed Queen TMB795C user manual — Make-Up Air
Page 19 · click to enlarge
Page 19

Exhaust Requirements

Venting

Proper sized exhaust ducts are essential for proper operation. All elbows should be sweep type. Exhaust ducts must be assembled so the interior surfaces are smooth to prevent the accumulation of lint.

A drying tumbler produces combustible lint. To reduce the risk of fire, the tumbler must be exhausted to the outdoors.

DO NOT use plastic or thin foil flexible ducts. Use exhaust ducts made of sheet metal or other noncombustible material. Use duct tape or pop-rivets on all seams and joints.

W057 To reduce the risk of fire and accumulation of combustible gases, DO NOT exhaust tumbler air into a window well, gas vent, chimney or enclosed, unventilated area such as an attic wall, ceiling, crawl space under a building, or concealed space of a building.

Verify that old ducts are thoroughly cleaned out before installing new tumbler.

Make-Up Air

A tumbler is forced air exhausted and requires provisions for make-up air to replace the air exhausted by the tumbler.

050 928 cm2 (144 in2)

075 1258 cm2 (195 in2)

Make-up air openings with louvers will restrict airflow. The opening must be increased to compensate for area taken up by louvers.

If it is necessary to duct make-up air to the tumbler(s), increase the area of the ductwork by 25% to compensate for any restriction in air movement.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Model Opening

Page 20 of the Speed Queen TMB795C user manual — Grounding Instructions
Page 20 · click to enlarge
Page 20

Electrical Requirements

  • Metal conduit and/or BX cable is not considered ground.
  • Connecting the Neutral from the electrical service box to the tumbler ground screw does not constitute a ground.
  • To reduce the risk of electric shock, fire, explosion, serious injury or death:
  • Disconnect electric power to the tumbler before servicing.
  • Close gas shut-off valve to gas tumbler before servicing.
  • Close steam valve to steam tumbler before servicing.
  • Never start the tumbler with any guards/ panels removed.
  • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded.
  • A dedicated ground conduit (wire) must be connected between the electrical service box ground bar and the tumbler ground screw.

To reduce the risk of electrical shock, de-energize the electrical circuit being connected to the tumbler before making any electrical connections. All electrical connections should be made by a qualified electrician. Never attempt to connect a live circuit.

W002 To reduce the risk of fire and electric shock, check with a qualified serviceman for proper grounding procedures. Improper connection of the equipment grounding conductor may result in a risk of electric shock.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

W068 To reduce the risk of fire and electric shock, if electrical supply is coming from a three phase service, DO NOT connect a “High Leg” or “Stinger Leg” to a single phase machine. On a three phase machine, if there is a “High Leg” or “Stinger Leg” it should be connected to L3.

All OPL (non-vend) models are factory-equipped with an emergency stop button on the front panel.

Grounding Instructions

In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This tumbler must be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the appropriate ground location.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 21 of the Speed Queen TMB795C user manual — Steam Requirements
Page 21 · click to enlarge
Page 21

Steam Requirements

Thermal Oil Prep

Obtain specific steam service pipe sizes from the steam system supplier or a qualified steam fitter.

It is the responsibility of the customer to install appropriate coil and heating system for thermal oil prep models. Alliance Laundry Systems, LLC. is not responsible for the performance or safety of the customer installed thermal oil system. To ensure proper operation, refer to the Specifications and Dimensions section for the BTU input of equivalent steam models. Thermal oil systems that do not deliver appropriate BTUs will dry slower. For solenoid valve wiring connections, refer to the Wiring Diagram supplied with tumbler.

  • Refer to Figure 3 for proper steam pipe configurations.
  • When tumbler is on the end of a line of equipment, extend header at least 1.2 meters (4 feet) beyond tumbler. Install shut-off valve, union, check valve and bypass trap at end of line. If the system has a gravity return to boiler, omit trap.
  • Insulate steam supply and return lines for safety of operator and safety while servicing tumbler.
  • Keep tumbler in good working condition. Repair or replace any worn or defective parts.

All system components must have a 8.6 bar (125 psig) working pressure. Shut-off valves must be installed upstream of the steam solenoid valve and downstream of each steam trap so components can be isolated for maintenance or emergency purposes.

All components (solenoid valve, traps) must be supported to minimize loads on the tumbler steam coil connections.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 22 of the Speed Queen TMB795C user manual — Steam Requirements
Page 22 · click to enlarge
Page 22
Speed Queen TMB795C — Steam Requirements diagram (page 22)
Fig. 6 · Steam Requirements

1 Supply 8 457 mm (18 in.) Drop 2 305 mm (12 in.) Riser 9 Solenoid Valve (Supplied with machine) 3 Shut-Off Valve 10 Steam Bonnet 4 Condensate Return Line from Supply Line 11 Flexible Line 5 Return 12 Union 6 Check Valve 13 Trap with Built-In Strainer 7 Vacuum Breaker (Optional)

Steam Pressure bar (PSI) Minimum Pipe Diameter Steam Trap Size* (Pounds Condensate/Hour)

5.3 - 6.9 (80-100) 3/4 in. NPT 160

* Based on 100 PSI.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Table 2

Page 23 of the Speed Queen TMB795C user manual — Step 4: Remove Laundry
Page 23 · click to enlarge
Page 23

Installation/Operation Supplement Operation

  • To reduce the risk of fire:
  • DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials.
  • DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning cloths, or anything dry-cleaned at home with a dry-cleaning solvent.
  • DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.

W076 To reduce the risk of serious injury, allow cylinder to stop before cleaning lint screen.

Emergency Stop Button

Operating Instructions

All OPL tumblers are factory-equipped with an emergency stop button located on the front panel. Refer to Figure 4.

Step 1: Clean Lint Screen/Compartment

Remove any accumulated lint from the lint screen and compartment. Close panel tightly against tumbler frame and lock panel securely, if applicable.

Step 2: Load Laundry

Open loading door and load cylinder with laundry. DO NOT OVERLOAD.

TMB1666N 1 Emergency Stop Button

Close loading door. Tumbler will not operate with the door open.

To operate emergency stop button:

a. Press red emergency stop button to stop all

Step 3: Determine Control Type and Temperature Setting

action.

b. To restart machine, pull red emergency stop

button out and press START pad or button.

Refer to the various controls in the Control Instructions section, pages 22 - 27, determine appropriate control and then follow the instructions.

The type of fabric being dried will determine the temperature setting. Consult the fabric care label or fabric manufacturer to determine proper temperature setting.

Step 4: Remove Laundry

When the cycle is complete, open door and remove the laundry.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 21 M414884 (EN)

Page 24 of the Speed Queen TMB795C user manual — INSERT QUARTER TURN KNOB
Page 24 · click to enlarge
Page 24

Control Instructions

3. Press the PUSH TO START button and hold it for approximately three (3) seconds.

Electromechanical Coin Control

CD, CX and CY Control Suffixes

PUSH

TO START

1. Set the TEMPERATURE selector at HIGH or LOW, or anywhere between these settings.

TEMPERATURE

HIGH

LOW

2. Coin Drop Models: Insert the coin(s) in the coin slot, turn the knob to the right and release it.
4. When the cycle is complete, open door and remove the laundry.

INSERT QUARTER TURN KNOB

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 25 of the Speed Queen TMB795C user manual — TEMPERATURE
Page 25 · click to enlarge
Page 25

Manual Timer Control

5. Press the PUSH TO START button in, and hold it in for approximately three (3) seconds. This starts the tumbler cycle.

MT and RT Control Suffixes

1. Set the HEAT/DRYING timer for the number of minutes (from 0-60) desired.

PUSH

TO START

HEAT

2. Set the COOL DOWN/COOLING timer for the number of minutes (from 0-15) desired.
6. When the cycle is complete, open door and remove the laundry.

5 COOL DOWN

3. Set the TEMPERATURE selector at HIGH, LOW or anywhere between these settings.

TEMPERATURE

HIGH

LOW

4. Select reversing or nonreversing cylinder rotation setting, if applicable.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 26 of the Speed Queen TMB795C user manual — Dual Digital Timer Control
Page 26 · click to enlarge
Page 26

Dual Digital Timer Control

4. Select reversing or nonreversing cylinder rotation setting, if applicable.

QT and RQ Control Suffixes

Speed Queen TMB795C — Dual Digital Timer Control diagram (page 26)
Fig. 7 · Dual Digital Timer Control
1. Select HIGH, MED, LOW or NO HEAT by turning the temperature knob.
Speed Queen TMB795C — Dual Digital Timer Control diagram (page 26)
Fig. 8 · Dual Digital Timer Control
5. Press and release START button to start tumbler. Display will show minutes remaining before end of cycle.
Speed Queen TMB795C — Dual Digital Timer Control diagram (page 26)
Fig. 9 · Dual Digital Timer Control
2. Set the HEAT TIME for the number of minutes (from 0 - 60) desired.
Speed Queen TMB795C — Dual Digital Timer Control diagram (page 26)
Fig. 10 · Dual Digital Timer Control
3. Set the COOL DOWN TIME for the number of minutes (from 0 - 15) desired.
Speed Queen TMB795C — Dual Digital Timer Control diagram (page 26)
Fig. 11 · Dual Digital Timer Control
6. When the cycle is complete, open door and remove the laundry.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 27 of the Speed Queen TMB795C user manual — REVERSING
Page 27 · click to enlarge
Page 27

Electronic OPL Micro Control

3. Press START pad to start tumbler.

G Models Through Serial No. 0110002231 and H, L, P, S, U and Y Models with OM and RM Control Suffixes

START

1. To use an Automatic Cycle, press an ON/ SELECT pad. Select HIGH, MEDIUM, MED LOW, LOW or NO HEAT for items that should not be dried with heat. A light to the left of the selected pad lights up.

To use a Time Dry or Custom Cycle, refer to the Programming Manual.

STOP/RESET

ON / SELECT

HIGH

MEDIUM

MED LOW

LOW

NO HEAT

4. When the cycle is complete, open door and remove the laundry.
2. Select REVERSING or NONREVERSING cylinder rotation setting.

REVERSING

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 28 of the Speed Queen TMB795C user manual — Electronic OPL Micro Control
Page 28 · click to enlarge
Page 28

G Models Starting Serial No. 0707xxxxx and K Models with OM and RM Control Suffixes

3. Press START pad to start tumbler.
1. To use an Automatic Cycle, press a TEMPERATURE pad. Select HIGH, MED, LOW, DELICATE or NO HEAT for items that should not be dried with heat. A light to the left of the selected pad lights up.

To use a Time Dry or Custom Cycle, refer to the Programming Manual.

2. Select REVERSING or NONREVERSING cylinder rotation setting.
4. When the cycle is complete, open door and remove the laundry.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 29 of the Speed Queen TMB795C user manual — START
Page 29 · click to enlarge
Page 29

Single Drop Control

MDC Coin and Card Control

SD and SX Control Suffixes

BC, BG, BL, BU, BX and BY Control Suffixes

1. Select HIGH, MED, LOW or NO HEAT by turning the temperature knob.
1. Select temperature by pressing the appropriate temperature pad.
Speed Queen TMB795C — Single Drop Control diagram (page 29)
Fig. 12 · Single Drop Control
2. Insert the coin(s) in the coin slot.
2. Insert the coin(s) in the coin slot, or the card into the opening.

TMB

TMB1492N TMB1963N

3. Press START button to start tumbler.
3. Press START pad to start tumbler.

START

4. When the cycle is complete, open door and remove the laundry.
4. When the cycle is complete, open door and remove the laundry.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Page 30 of the Speed Queen TMB795C user manual — Diagnostic LED (DGN LED) / Error Codes
Page 30 · click to enlarge
Page 30

Ignition Control Operation

Diagnostic LED (DGN LED) / Error Codes

The Diagnostic LED or DGN LED is located by the power connector on the ignition control. Refer to Figure 33. The Diagnostic LED will indicate the status of the ignition control. Refer to Table 3.

LED Color Description Orange-Yellow Initialization Green Standby / Normal Operation Red Fault Indication Code

The Diagnostic LED will flash error codes one half second on and one half second off. Error codes are separated by a one second pause before the code is repeated.

Error Code DGN LED status Fault Type

1 Red Ignition Control Internal Failure

2 2 Red Flashes Gas Valve Not Connected

3 3 Red Flashes Ignition/Flame Sense Failure

4 4 Red Flashes Reset Switch is Shorted

5 Slow Red and Green Flashes Low Voltage Detection

6 Fast Red and Orange Flashes Ignition Control is in Reset Delay

TMB2176N 1 Diagnostic (DGN) LED

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT

Table 3

Page 31 of the Speed Queen TMB795C user manual — MIX1N
Page 31 · click to enlarge
Page 31

Installation/Operation Supplement Disposal of Unit

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Refer to Figure 34. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact the local city office, household waste disposal service, or the source from which the product was purchased. Figure 34

MIX1N

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 29 M414884 (EN)

Display codes

Error codes

What the fault codes shown on the display mean and how to clear them.

CodeMeaningFix
1Ignition Control Internal Failure p.30
2Gas Valve Not Connected p.30
3Ignition/Flame Sense Failure p.30
4Reset Switch is Shorted p.30
5Low Voltage Detection p.30
6Ignition Control is in Reset Delay p.30

Ask about the Speed Queen TMB795C

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Speed Queen TMB795C

Be the first to ask — other owners or our team will answer.

Original document

Speed Queen TMB795C manual PDF

31 pages·1.1 MB·Clothes Dryer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…