EN
Speed Queen logo
Official user manual

Speed Queen JC50CE

66 pages·737 KB·Clothes Dryer·PDF·ENDEFRITNLJA
Speed Queen JC50CE
Table of Contents 80 sections Installation and Maintenance · Instructions for Drying · Tumblers · 30 Pound (13 Kg) Capacity · … ShowHide
Installation and Maintenancep.1Instructions for Dryingp.1Tumblersp.130 Pound (13 Kg) Capacityp.150 Pound (22 Kg) Capacityp.1SCB50CSH and SCB50EGp.175 Pound (34 Kg) Capacityp.1JC75CE, JC75CG, JC75CSH, JCB75CE, JCB75CG, JCB75CSH, SC75CE,p.1SC75CG, SC75CSH, SCB75CE, SCB75CG and SCB75CSHp.1WARNINGS AND LABELSp.3WARNING p.4NAMEPLATE LOCATIONp.6REPLACEMENT PARTS INFORMATIONp.6T024IE3Bp.7TOP VIEW OF EXHAUSTp.7T258IE3Ap.7DISCONNECTp.7SWITCHp.7EXHAUSTp.7AIR FLOWp.7GAS CONNECTION AND SHUT OFFp.7VALVEp.7ELECTRICAL JUNCTION BOXp.7T257IE3Bp.730 Pound (13 kg) Narrow Cabinet Gas Tumblerp.830 Pound (13 kg) Narrow Cabinet Electric Tumblerp.9T259IE3Bp.930 Pound (13 kg) Gas Tumblerp.11GAS CONNECTIONp.11AND SHUT OFF VALVE AIR FLOW SWITCHp.11THIMBLE CONNECTIONp.11T266IE3Bp.1130 Pound (13 kg) Electric Tumblerp.13T267IE3Bp.1330 Pound (13 kg) Steam Tumblerp.15OUTLET ELECTRICAL JUNCTION BOXp.15T268IE3Bp.1550 Pound (22 kg) Gas Non-reversing Tumblersp.17AND SHUT OFFp.17VALVE AIR FLOW SWITCHp.17T269IE3Bp.1750 Pound (22 kg) Gas Tumblersp.18REVERSING MOTOR SIZESp.18STEAMp.18GAS ELECTRICp.18HIGH PRESSURE LOW PRESSUREp.1850 Pound (22 kg) Gas and Steam Reversing Tumblersp.19CYLINDERp.19MOTORp.19AIRFLOWp.19FAN MOTORp.19T264IE3Bp.1950 Pound (22 kg) Electric Non-reversing Tumblersp.20T270IE3Bp.2050 Pound (22 kg) Electric Tumblersp.2150 Pound (22 kg) Electric Reversing Tumblersp.22T263IE3Bp.2250 Pound (22 kg) Steam Non-reversing Tumblersp.23T271IE3Ap.2350 Pound (22 kg) Steam Tumblersp.2475 Pound (34 kg) Gas Non-reversing Tumblersp.25AND SHUT OFF VALVEp.25T272IE3Bp.2575 Pound (34 kg) Gas and Steam Reversing Tumblersp.26T265IE3Bp.2675 Pound (34 kg) Gas Tumblersp.2775 Pound (34 kg) Electric Non-reversing Tumblersp.28T273IE3Bp.2875 Pound (34 kg) Electric Reversing Tumblersp.2975 Pound (34 kg) Electric Tumblersp.3075 Pound (34 kg) Steam Non-reversing Tumblersp.31T274IE3Bp.3175 (34 kg) Pound Steam Tumblersp.32SECTION II Installation Instructionsp.33RECEIVING INSPECTIONp.33MATERIALS REQUIRED (Obtain Locally)p.33GAS, ELECTRIC OR STEAM DRYING TUMBLERSp.33GAS DRYING TUMBLERS ONLYp.33STEAM DRYING TUMBLERS ONLYp.33FACILITIES REQUIREDp.33
Page 1 of the Speed Queen JC50CE user manual — SCB50CSH and SCB50EG
Page 1 · click to enlarge
Page 1

Installation and Maintenance

Instructions for Drying

Tumblers

30 Pound (13 Kg) Capacity

JCB30CE, JCB30CG, JCB30CSH, JCB30CSL, JCB30WE, JCB30XG, SCB30CE, SCB30CG, SCB30CSH, SCB30CSL, SCB30WE and SCB30XG

50 Pound (22 Kg) Capacity

JC50CE, JC50CG, JC50CSH, JC50EG, JCB50CE, JCB50CG, JCB50CSH, JCB50EG, SC50CE, SC50CG, SC50CSH, SC50EG, SCB50CE, SCB50CG,

SCB50CSH and SCB50EG

75 Pound (34 Kg) Capacity

JC75CE, JC75CG, JC75CSH, JCB75CE, JCB75CG, JCB75CSH, SC75CE,

SC75CG, SC75CSH, SCB75CE, SCB75CG and SCB75CSH

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If this tumbler changes ownership, be sure this manual accompanies the tumbler).

A copy of the operating instruction must remain with the tumbler after installation.

To locate the servicer nearest you, call (414) 748-3121.

Part No. M412616 1/95

Manufactured By: Speed Queen Company P.O. Box 990 Ripon, WI 54971-0990 U.S.A.

Distributed By:

Page 2 of the Speed Queen JC50CE user manual — Installation and Maintenance
Page 2 · click to enlarge
Page 2
Page 2 of the Speed Queen JC50CE user manual — Installation and Maintenance
Page 3 of the Speed Queen JC50CE user manual — WARNINGS AND LABELS
Page 3 · click to enlarge
Page 3

WARNINGS AND LABELS

FAILURE TO INSTALL, MAINTAIN, AND/OR OPERATE THIS MACHINE ACCORDING TO MANUFACTURER’S INSTRUCTIONS MAY RESULT IN CONDITIONS WHICH CAN PRODUCE SERIOUS INJURY, DEATH AND/OR PROPERTY DAMAGE.

Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand.

aWARNING To reduce the risk of fire, electrical shock, serious injury or death to persons do not operate the tumbler if it does not perform according to these instructions. Immediately disconnect electrical service, shut off gas supply and contact an authorized service representative. Service and repairs are to be performed by authorized service representatives only.

aWARNING To reduce the risk of fire, electrical shock, serious injury or death to persons when using the tumbler unit, follow these basic precautions:

· Read all instructions before using tumbler. · DO NOT tamper with controls. · DO NOT bypass any safety devices. · Always follow the fabric care instructions supplied by the garment manufacturer. · Remove laundry immediately after the tumbler stops. · DO NOT reach into tumbler if cylinder is revolving.

aWARNING To avoid creating any flammable vapors which may explode, ignite or cause corrosive damage, DO NOT dry the following materials:

· Articles that have been cleaned in, soaked in, washed in or spotted with gasoline, dry cleaning solvents or other flammable/explosive substances. · Plastics or articles containing foam rubber or similarly textured rubberlike materials. · Articles that have traces of flammable substances like cooking oil, machine, oil, flammable chemicals or thinner. · Articles containing wax or cleaning chemicals. · Fiberglass curtains or draperies (unless the label says it can be done).

aWARNING To reduce the risk of serious injury, install lockable door(s) to prevent public access to rear of tumblers.

1 M412616 © Copyright 1994. All Rights Reserved.

aWARNING

Page 4 of the Speed Queen JC50CE user manual — WARNING
Page 4 · click to enlarge
Page 4

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your dryer, follow these basic precautions:

1. Do not allow children to play on or in the tumbler. Close supervision of children is necessary when the tumbler is used near children. This is a safety rule for all appliances.
2. Before the tumbler is removed from service or discarded, remove the door to the drying compartment.
3. Do not install or store the tumbler where it will be exposed to water and/or weather.
4. Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce serious injury, death and/or property damage.
5. Run tumbler with a load before putting tumbler into service.
6. Always disconnect the electrical power to the tumbler before servicing. Disconnect power by shutting off appropriate circuit breaker or fuse and by turning off the disconnect switch located on the rear of te tumbler.
7. All manually operated models are factory-equipped with an emergency stop button located on the front panel. If the emergency stop function is desired on coin-operated models, an external emergency stop switch may be installed as specified on the machine wiring diagram.

The following warning labels will be found on the drying tumbler:

A clothes dryer produces combustible lint. TUMBLER MUST BE EXHAUSTED OUTDOORS.

Do not touch rotating parts.

Speed Queen JC50CE — WARNING  diagram (page 4)
Fig. 1

Do not touch surface until it has cooled.

Do not operate without guards in place.

Disconnect electrical power before servicing.

To reduce risk of accumulating unsafe concentrations of combustion gases, tumbler MUST BE EXHAUSTED OUTDOORS.

Page 5 of the Speed Queen JC50CE user manual — WARNING
Page 5 · click to enlarge
Page 5
Page 5 of the Speed Queen JC50CE user manual — WARNING
Page 6 of the Speed Queen JC50CE user manual — REPLACEMENT PARTS INFORMATION
Page 6 · click to enlarge
Page 6

NAMEPLATE LOCATION

Speed Queen JC50CE — NAMEPLATE LOCATION diagram (page 6)
Fig. 2

When writing for information on any tumbler, be sure to mention

When writing for information on any tumbler, be sure to mention model and serial numbers. The model and serial numbers will be found on the nameplate as shown on the rear of tumbler or underneath the door hinge.

REPLACEMENT PARTS INFORMATION

If replacement parts are required, contact the source from whom you purchased your tumbler or, contact the Ripon Service Parts Center, P.O. Box 990, Ripon, Wisconsin 54971-0990, for the name and address of the nearest authorized parts distributor.

Page 7 of the Speed Queen JC50CE user manual — T257IE3B
Page 7 · click to enlarge
Page 7

SECTION I Roughing-In Dimensions and Specifications 30 Pound (13 kg) Narrow Cabinet Gas Tumbler

SIDE PANEL 8.59 cm (3-3/8")

67.95 cm (26-3/4")

8.59 cm (3-3/8")

T024IE3B

TOP VIEW OF EXHAUST

3.81 cm (1-1/2")

81.76 cm (32-3/16")

113.98 cm (44-7/8")

T258IE3A

DISCONNECT

SWITCH

15.24 cm (6") DIAMETER

EXHAUST

AIR FLOW

SWITCH

GAS CONNECTION AND SHUT OFF

183.52 cm (72-1/4")

VALVE

CLEARANCESMinimum

ELECTRICAL JUNCTION BOX

to nearest Combustible Material Top —

12" (30.5 cm) Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.12 cm (28")

T257IE3B

Page 8 of the Speed Queen JC50CE user manual — 30 Pound (13 kg) Narrow Cabinet Gas Tumbler
Page 8 · click to enlarge
Page 8

30 Pound (13 kg) Narrow Cabinet Gas Tumbler

Cabinet Finish:Electrostatically applied thermosetting polyester. Cylinder:26.5" x 30" (67.3 cm x 76.2 cm) perforated galvanized steel with three baffles Motor:¹⁄₃ H.P., lifetime lubricated, internal overload protected Electrical Requirements:230 Volt, 50 Hertz, 1 Phase; 5.5 Amps Gas Consumption:75,000 BTU per hour (79.1 MJ/hr.) Gas Connection:1/2" (12.7 mm) N.P.T. Types of Gas:Factory equipped with Natural/Mixed Gas (6¹⁄₂ ± 1¹⁄₂ inch water column line pressure) (1.62 ± .37 kPa); or Liquefied Petroleum gas (11 ± .3" water column line pressure) (2.74 ± .07 kPa) Air Flow:370 C.F.M. at 0.5" W.C. (175 liters/sec. at 1.25 mBar) Net Weight:350 Pounds (159 kg) (approximate)
Page 9 of the Speed Queen JC50CE user manual — T259IE3B
Page 9 · click to enlarge
Page 9

30 Pound (13 kg) Narrow Cabinet Electric Tumbler

SIDE PANEL 8.59 cm (3-3/8") 67.95 cm 8.59 cm (26-3/4") (3-3/8") T024IE3B TOP VIEW OF EXHAUST 3.81 cm (1-1/2") 81.76 cm (32-3/16") 113.98 cm (44-7/8") T258IE3A 81.76 cm (32-3/16") 67.95 cm (26-3/4") 3.81 cm (1-1/2") 113.98 cm (44-7/8")
Speed Queen JC50CE — 30 Pound (13 kg) Narrow Cabinet Electric Tumbler diagram (page 9)
Fig. 3 · 30 Pound (13 kg) Narrow Cabinet Electric Tumbler

DISCONNECT

SWITCH

Speed Queen JC50CE — DISCONNECT diagram (page 9)
Fig. 4

15.24 cm (6") DIAMETER

ELECTRICAL JUNCTION BOX

EXHAUST

CLEARANCESMinimum

to nearest Combustible Material Top —

12" (30.5 cm) Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

T259IE3B

Page 10 of the Speed Queen JC50CE user manual — 30 Pound (13 kg) Narrow Cabinet Electric Tumbler
Page 10 · click to enlarge
Page 10

30 Pound (13 kg) Narrow Cabinet Electric Tumbler

Cabinet Finish:Electrostatically applied thermosetting polyester. Cylinder:26.5" x 30" (67.3 cm x 76.2 cm) perforated galvanized steel with three baffles Motor:¹⁄₃ H.P., lifetime lubricated, internal overload protected Electrical Requirements: (See nameplate for voltage of your tumbler)230 Volt, 50 Hertz, 1 Phase; 90 Amps 230 Volt, 50 Hertz, 3 Phase; 53 Amps 380 Volt, 50 Hertz, 3 Phase; 33 Amps 415 Volt, 50 Hertz, 3 Phase; 30 Amps Element:18,000 Watts Air Flow :625 C.F.M. at 0.5" W.C. (294 liters/sec. at 1.25 mBar) Net Weight:410 Pounds (184.5 kg) (approximate)
Page 11 of the Speed Queen JC50CE user manual — T266IE3B
Page 11 · click to enlarge
Page 11

30 Pound (13 kg) Gas Tumbler

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.5 cm (28-1/4")

3.81 cm (1-1/2")

81.75 cm (32-3/16")

DISCONNECT

114 cm (44-7/8") 118.6 cm (46-11/16")

SWITCH

GAS CONNECTION

AND SHUT OFF VALVE AIR FLOW SWITCH

ELECTRICAL JUNCTION BOX

20.3 cm (8") DIAMETER EXHAUST DUCT

183.5 cm (72-1/4")

THIMBLE CONNECTION (Energy Saver

157.8 cm (62-1/8")

140.7 cm (55-3/8")

11.3 cm (4-7/16")

20.3 cm (8") DIAMETER EXHAUST DUCT

THIMBLE CONNECTION

AIR FLOW SWITCH (Energy Saver Models)

55.6 cm (21-7/8")

T266IE3B

Show 5 more labels / short text on this page
(Standard Models) · Models) · (Standard · Models) · 80 cm (31-1/2")
Page 12 of the Speed Queen JC50CE user manual — 30 Pound (13 kg) Gas Tumbler
Page 12 · click to enlarge
Page 12

30 Pound (13 kg) Gas Tumbler

Cabinet Finish:Electrostatically applied thermosetting polyester Cylinder:30" x 30" (76.2 x 76.2 cm) perforated galvanized steel with three baffles; 30 pounds (13.6 kg) dry weight (cotton load) Motor:¹⁄₃ H.P., lifetime lubricated, internal overload protected Electrical Requirements:230 Volt, 50 Hertz, 1 Phase, 5.5 Amp Gas Consumption:Energy Saver Models — 80,000 BTU per hour (84.4 MJ/hr.) Standard Models — 105,000 BTU per hour (110.8 MJ/hr.) Types of Gas:Factory equipped with Natural/Mixed Gas (6¹⁄₂ ± 1¹⁄₂ inch water column line pressure) (1.62 ± .37 kPa); or Liquefied Petroleum gas (11 ± .3" water column line pressure) (2.74 ± .07 kPa) Gas Connection:¹⁄₂ inch (12.7 mm) N.P.T. Air Flow:600 C.F.M. at 0.5 " W.C. (283 liters/sec. at 1.25 mBar) Net Weight:450 Pounds (204 kg.) (approximate) Calorific Value:Natural Gas — 8900 kCal/m3 (37.2 MJ/m3) L.P. Gas — 22,250 kCal/m3 (93.1 MJ/m3)
Page 13 of the Speed Queen JC50CE user manual — AIR FLOW
Page 13 · click to enlarge
Page 13

30 Pound (13 kg) Electric Tumbler

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.7 cm (28-1/4")

3.81 cm (1-1/2")

81.75 cm (32-3/16")

DISCONNECT

SWITCH

ELECTRICAL JUNCTION BOX

183.5 cm (72-1/2")

11.3 cm (4-7/16")

20.3 cm (8") DIAMETER EXHAUST DUCT

THIMBLE CONNECTION

55.6 cm (21-7/8")

AIR FLOW

SWITCH

T267IE3B

114 cm (44-7/8") · 80 cm (31-1/2")

Page 14 of the Speed Queen JC50CE user manual — 30 Pound (13 kg) Electric Tumbler
Page 14 · click to enlarge
Page 14

30 Pound (13 kg) Electric Tumbler

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 30" x 30" (76.2 x 76.2 cm) perforated galvanized steel with three baffles; 30 pounds (13.6 kg) dry weight (cotton load)

Motor¹⁄₃ H.P., lifetime lubricated, internal overload protected

Electrical Requirements: 230 Volt, 50 Hertz, 1 Phase, 90 Amp (see nameplate for voltage 230 Volt, 50 Hertz, 3 Phase, 54 Amp of your tumbler) 380 Volt, 50 Hertz, 3 Phase, 33 Amp 415 Volt, 50 Hertz, 3 Phase, 30 Amp

Element21,000 Watts (all voltages)
Air Flow600 C.F.M. at 0.5" W.C. (283 liters/sec. at 1.25 mBar)
Net Weight450 pounds (204 kg) (approximate)
Page 15 of the Speed Queen JC50CE user manual — T268IE3B
Page 15 · click to enlarge
Page 15

30 Pound (13 kg) Steam Tumbler

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.75 cm (28-1/4")

3.81 cm (1-1/2")

81.75 cm (32-3/16")

114 cm (44-7/8") (High Pressure Models)

DISCONNECT

114.4 cm (45-1/32") (Low Pressure Models)

SWITCH

35.6 cm (14")

19.05 cm (7-1/2") 1.9 cm (3/4") I.D. STEAM

OUTLET ELECTRICAL JUNCTION BOX

1.9 cm (3/4") I.D. STEAM OUTLET

183.5 cm (72-1/4")

174.6 cm (68-3/4")

155.6 cm (61-1/4")

11.27 cm (4-7/16")

20.3 cm (8") DIAMETER EXHAUST DUCT

THIMBLE CONNECTION

55.56 cm (21-7/8")

T268IE3B

80 cm (31-1/2")

Page 16 of the Speed Queen JC50CE user manual — 30 Pound (13 kg) Steam Tumbler
Page 16 · click to enlarge
Page 16

30 Pound (13 kg) Steam Tumbler

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 30" x 30" (76.2 x 76.2 cm) perforated galvanized steel with three baffles; 30 pounds dry weight (13.6 kg) (cotton load)

Motor: High Pressure (4 coils) ¹⁄₂ H.P. Low Pressure (4 coils) ³⁄₄ H.P.

Boiler Horsepower: 4 coil High Pressure – 3.7 Bhp (123,950 BTU/hr., 58 kg/hr, 31,235 kCal/hr.) 4 coil Low Pressure – 2.6 Bhp (87,100 BTU/hr., 40 kg/hr, 21,949 kCal/hr.)

Electrical Requirements: Low Pressure: (see nameplate for 230 Volt, 50 Hertz, 1 Phase, 8 Amp voltage of tumbler) 380 Volt, 50 Hertz, 3 Phase, 3 Amp 415 Volt, 50 Hertz, 3 Phase, 3 Amp

High Pressure:

230 Volt, 50 Hertz, 1 Phase, 4 Amp 380-415 Volt, 50 Hertz, 3 Phase, 2 Amp

Air Flow: Low Pressure — 600 C.F.M. at 0.5 W.C. (283 liters/sec. at 1.25 mBar) High Pressure — 600 C.F.M. at 0.5 W.C. (283 liters/sec. at 1.25 mBar)

Net Weight470 pounds (214 kg) (approximate)
Page 17 of the Speed Queen JC50CE user manual — THIMBLE CONNECTION
Page 17 · click to enlarge
Page 17

50 Pound (22 kg) Gas Non-reversing Tumblers

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.75 cm (28-1/4")

3.81 cm (1-1/2")

81.75 cm (32-3/16")

119.4 cm (47")

DISCONNECT

GAS CONNECTION

SWITCH

AND SHUT OFF

VALVE AIR FLOW SWITCH

20.3 cm (8") DIAMETER EXHAUST DUCT

THIMBLE CONNECTION (Energy Saver

ELECTRICAL JUNCTION BOX

194.6 cm (76-5/8")

146.37 cm (57-5/8")

13.65 cm (5-3/8")

20.3 cm (8") DIAMETER EXHAUST DUCT

THIMBLE CONNECTION

AIR FLOW

T269IE3B

98.1 cm (38-5/8")

Show 8 more labels / short text on this page
(Standard Models) · Models) · 167 cm (65-3/4") · (Standard · Models) · 34 cm (13-3/8") · SWITCH (Energy Saver · Models)
Page 18 of the Speed Queen JC50CE user manual — REVERSING MOTOR SIZES
Page 18 · click to enlarge
Page 18

50 Pound (22 kg) Gas Tumblers

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 37" x 30" (94 cm x 76.2 cm) perforated galvanized steel with four baffles; 50 pounds (22.7 kg) dry weight (cotton load)

Motor1/2 H.P., lifetime lubricated, internal overload protected (Nonreversing Models) (See below for reversing models.)
Electrical Requirements230 Volt, 50 Hertz, 1 Phase, 6.0 Amp Non-Reversing Models
Electrical Requirements230 Volt, 50 Hertz, 1 Phase, 8.0 Amp Reversing Models

Gas Consumption: Energy Saver Models — 95,000 BTU per hour (100.2 MJ/hr.) Standard Models — 120,000 BTU per hour (126.6 MJ/hr.)

Types of Gas: Factory equipped with Natural/Mixed Gas (6-1/2 ± 1-1/2 inch water column line pressure) (1.62 ± .37 kPa); or Liquefied Petroleum gas (11 ± .3" water column line pressure) (2.74 ± .07 kPa)

Gas Connection: 1/2 inch (12.7 mm) N.P.T.

Air Flow: Energy Saver Models — 390 C.F.M. at 0.5" W.C. (185 liters/sec. at 1.25 mBar) Standard Models — 600 C.F.M. at 0.5" W.C. (284 liters/sec. at 1.25 mBar)

Net Weight545 Pounds (247 kg) (approximate)

Calorific Value: Natural Gas — 8900 kCal/m3 (37.2 MJ/m3) L.P. Gas — 22,250 kCal/m3 (93.1 MJ/m3)

REVERSING MOTOR SIZES

STEAM

GAS ELECTRIC

HIGH PRESSURE LOW PRESSURE

50 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.

CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

Page 19 of the Speed Queen JC50CE user manual — T264IE3B
Page 19 · click to enlarge
Page 19

50 Pound (22 kg) Gas and Steam Reversing Tumblers

ELECTRICAL JUNCTION BOX

DISCONNECT

SWITCH

CYLINDER

MOTOR

20.3 cm (8") DIAMETER EXHAUST THIMBLE

194.6 cm (76-5/8")

146.4 cm (57-5/8")

20.3 cm (8") DIAMETER

EXHAUST

THIMBLE CONNECTION

AIRFLOW

SWITCH

13.65 cm (5-3/8")

FAN MOTOR

98.1 cm (38-5/8")

T264IE3B

CONNECTOR (Energy Saver · Gas Models) · 34 cm (13-3/8")

Page 20 of the Speed Queen JC50CE user manual — T270IE3B
Page 20 · click to enlarge
Page 20

50 Pound (22 kg) Electric Non-reversing Tumblers

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.75 cm (28-1/4")

3.81 cm (1-1/2")

81.75 cm (32-3/16")

119.4 cm (47") DISCONNECT

SWITCH

ELECTRICAL JUNCTION BOX 20.3 cm (8") DIAMETER EXHAUST DUCT

194.6 cm (76-5/8")

THIMBLE CONNECTION

13.65 cm (5-3/8")

AIR FLOW

SWITCH

98.1 cm (38-5/8")

T270IE3B

34 cm (13-3/8")

Page 21 of the Speed Queen JC50CE user manual — REVERSING MOTOR SIZES
Page 21 · click to enlarge
Page 21

50 Pound (22 kg) Electric Tumblers

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 37" x 30" (94 x 76.2 cm) perforated galvanized steel with four baffles; 50 pounds (22.7 kg) dry weight (cotton load)

Motor1/2 H.P., lifetime lubricated, internal overload protected (Nonreversing models) (See below for reversing models.)

Electrical Requirements: 230 Volt, 50 Hertz, 1 Phase, 90 Amp (see nameplate for voltage 230 Volt, 50 Hertz, 3 Phase, 78 Amp of your tumbler) 380 Volt, 50 Hertz, 3 Phase, 48 Amp 415 Volt, 50 Hertz, 3 Phase, 45 Amp

Element30,000 watts (all voltages) Long life nichrome wire
Air Flow900 C.F.M. maximum at .5" W.C. (425 liters/sec at 1.25 mBar)
Net Weight550 pounds (250 kg) (approximate)

REVERSING MOTOR SIZES

STEAM

GAS ELECTRIC

HIGH PRESSURE LOW PRESSURE

50 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.

CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

Page 22 of the Speed Queen JC50CE user manual — T263IE3B
Page 22 · click to enlarge
Page 22

50 Pound (22 kg) Electric Reversing Tumblers

ELECTRICAL JUNCTION BOX

DISCONNECT

SWITCH

CYLINDER

MOTOR

194.6 cm (76-5/8")

20.3 cm (8") DIAMETER

EXHAUST

THIMBLE CONNECTION

AIRFLOW

SWITCH

13.65 cm (5-3/8")

FAN MOTOR

98.1 cm (38-5/8")

T263IE3B

34 cm (13-3/8")

Page 23 of the Speed Queen JC50CE user manual — T271IE3A
Page 23 · click to enlarge
Page 23

50 Pound (22 kg) Steam Non-reversing Tumblers

194. 6 cm (76-5/8") (4 Coil)

203.2 cm (80") (6 Coil)

71.75 cm (28-1/4")

3.81 cm (1-1/2")

81.75 cm (32-3/16")

119.4 cm (47")

38.7 cm (15-1/4") 19.05 cm (7-1/2")

1.9 cm (3/4") I.D. STEAM INLET

ELECTRICAL JUNCTION BOX

200 cm (78-3/4") (6 Coil)

1.9 cm (3/4") I.D. STEAM OUTLET

184.8 cm (72-3/4") (4 Coil)

164.5 cm (64-3/4")

13.65 cm (5-3/8")

20.3 cm (8") DIAMETER EXHAUST DUCT

THIMBLE CONNECTION

98.1 cm (38-5/8")

T271IE3A

34 cm (13-3/8")

Page 24 of the Speed Queen JC50CE user manual — REVERSING MOTOR SIZES
Page 24 · click to enlarge
Page 24

50 Pound (22 kg) Steam Tumblers

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 37" x 30" (94 x 76.2 cm) perforated galvanized steel with four baffles; 50 pounds (22.7 kg) dry weight (cotton load)

Motor: High Pressure Steam — 1/2 H.P. (Nonreversing Models) Low Pressure Steam — 3/4 H.P. Both motors are lifetime lubricated, internal overload protected (See below for reversing models.)

Boiler HorsepowerHigh Pressure Steam (6 Coil) — 4.60 BHP

(154,100 BTU/hr, 72.1 kg/hr, 38,833 kCal/nr.) Low Pressure Steam (4 Coil) — 3.00 BHP

(134,000 BTU/hr, 62.7 kg/hr, 33,768 kCal/hr.)

Electrical Requirements: Low Pressure (see nameplate for voltage 230 Volt, 50 Hertz, 1 Phase, 7.0 Amp of your tumbler)

High Pressure 230 Volt, 50 Hertz, 1 Phase, 7.0 Amp 380 Volt, 50 Hertz, 3 Phase, 3.0 Amp 415 Volt, 50 Hertz, 3 Phase, 2.5 Amp

Air Flow: Low Pressure — 950 C.F.M. at 0.5" W.C. (449 liters/sec. at 1.25 mBar) High Pressure — 900 C.F.M. at 0.5" W.C. (426 liters/sec. at 1.25 mBar)

Net Weight: 4 Coil Tumbler — 565 pounds (257 kg) (approximate) 6 Coil Tumbler — 580 pounds (263 kg) (approximate)

REVERSING MOTOR SIZES

STEAM

GAS ELECTRIC

HIGH PRESSURE LOW PRESSURE

50 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.

CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

Page 25 of the Speed Queen JC50CE user manual — T272IE3B
Page 25 · click to enlarge
Page 25

75 Pound (34 kg) Gas Non-reversing Tumblers

71.75 cm (28-1/4")

3.81 cm (1-1/2")

DISCONNECT

134.6 cm (53")

SWITCH

ELECTRICAL JUNCTION BOX

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

194.6 cm (76-5/8")

GAS CONNECTION

AND SHUT OFF VALVE

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

13.65 cm (5-3/8")

20.3 cm (8") DIAMETER EXHAUST DUCT

Minimum recommended for service access. Sides — 0" Permitted.

THIMBLE CONNECTION (Standard Models) AIR FLOW

SWITCH

98.1 cm (38-5/8")

T272IE3B

97 cm (38-3/16") · 167 cm (65-3/4") · 34 cm (13-3/8")

Page 26 of the Speed Queen JC50CE user manual — T265IE3B
Page 26 · click to enlarge
Page 26

75 Pound (34 kg) Gas and Steam Reversing Tumblers

DISCONNECT

ELECTRICAL JUNCTION BOX

SWITCH

CYLINDER

MOTOR

194.6 cm (76-5/8")

20.3 cm (8") DIAMETER

EXHAUST

THIMBLE CONNECTION

AIRFLOW

SWITCH

13.65 cm (5-3/8")

FAN MOTOR

98.1 cm (38-5/8")

T265IE3B

34 cm (13-3/8")

Page 27 of the Speed Queen JC50CE user manual — REVERSING MOTOR SIZES
Page 27 · click to enlarge
Page 27

75 Pound (34 kg) Gas Tumblers

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 37" x 36" (94 x 91.4 cm) perforated galvanized steel cylinder with four baffles; 75 pounds (34.1 kg) dry weight (cotton load)

Motor3/4 H.P., lifetime lubricated, internal overload protected. (Non-reversing models) (See below for reversing models.)

Electrical Requirements Nonreversing Models: 230 Volt, 50 Hertz, 1 Phase, 9.0 Amp

Electrical Requirements Reversing Models230 Volt, 50 Hertz, 1 Phase, 9.0 Amp
Gas Consumption165,000 B.T.U. per hour (174.1 MJ/hr.)

Types of Gas: Factory equipped with Natural/Mixed gas (6-1/2 A 1-1/2 inch water column line pressure) (1.62 A .37 kPa); or Liquefied Petroleum gas (11.0 A .3 inch water column line pressure) (2.74 A .07 kPa)

Gas Connection: 1/2 inch (12.7 mm) N.P.T.

Air Flow1000 C.F.M. at 0.5" W.C. (472 liters/sec. at 1.25 mBar)
Net Weight550 Pounds (250 kg) (approximate)

Calorific Value: Natural Gas — 8900 kCal/m3 (37.2 MJ/m3) L.P. Gas — 22250 kCal/m3 (93.1 MJ/m3)

REVERSING MOTOR SIZES

STEAM

GAS ELECTRIC

HIGH PRESSURE LOW PRESSURE

75 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.

CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

Page 28 of the Speed Queen JC50CE user manual — T273IE3B
Page 28 · click to enlarge
Page 28

75 Pound (34 kg) Electric Non-reversing Tumblers

CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

71.75 cm (28-1/4")

3.81 cm (1-1/2")

DISCONNECT

134.6 cm (53")

SWITCH

ELECTRICAL JUNCTION BOX

194.6 cm (76-5/8")

20.3 cm (8") DIAMETER EXHAUST DUCT

13.65 cm (5-3/8")

THIMBLE CONNECTION

AIR FLOW

SWITCH

98.1 cm (38-5/8")

T273IE3B

97 cm (38-3/16") · 34 cm (13-3/8")

Page 29 of the Speed Queen JC50CE user manual — T263IE3B
Page 29 · click to enlarge
Page 29

75 Pound (34 kg) Electric Reversing Tumblers

DISCONNECT

ELECTRICAL JUNCTION BOX

SWITCH

CYLINDER

MOTOR

194.6 cm (76-5/8")

20.3 cm (8") DIAMETER

EXHAUST

THIMBLE CONNECTION

AIRFLOW

SWITCH

13.65 cm (5-3/8")

FAN MOTOR

98.1 cm (38-5/8")

T263IE3B

34 cm (13-3/8")

Page 30 of the Speed Queen JC50CE user manual — REVERSING MOTOR SIZES
Page 30 · click to enlarge
Page 30

75 Pound (34 kg) Electric Tumblers

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 3 7" x 36" (94 x 91.4 cm) perforated galvanized steel with four baffles; 75 pounds (34.1 kg) dry weight (cotton load)

Motor3/4 H.P., lifetime lubricated internal overload protected. (Non-reversing models) (See below for reversing models.)

Electrical Requirements: 230 Volt, 50 Hertz, 3 Phase, 77 Amps (See nameplate 380 Volt, 50 Hertz, 3 Phase, 50 Amps for voltage of 415 Volt, 50 Hertz, 3 Phase, 45 Amps your tumbler)

Element30,000 Watts (all models)
Air Flow850 C.F.M. at 0.5" W.C. (401 liters/sec at 1.25 mBar)
Net Weight555 Pounds (252 kg) (approximate)

REVERSING MOTOR SIZES

STEAM

GAS ELECTRIC

HIGH PRESSURE LOW PRESSURE

75 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.

CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

Page 31 of the Speed Queen JC50CE user manual — ELECTRICAL JUNCTION BOX
Page 31 · click to enlarge
Page 31

75 Pound (34 kg) Steam Non-reversing Tumblers

Speed Queen JC50CE — 75 Pound (34 kg) Steam Non-reversing Tumblers diagram (page 31)
Fig. 5 · 75 Pound (34 kg) Steam Non-reversing Tumblers
CLEARANCESMinimum

to nearest Combustible Material Top — 12" (30.5 cm)

Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm)

Minimum recommended for service access. Sides — 0" Permitted.

ELECTRICAL JUNCTION BOX

T274IE3B

Page 32 of the Speed Queen JC50CE user manual — REVERSING MOTOR SIZES
Page 32 · click to enlarge
Page 32

75 (34 kg) Pound Steam Tumblers

Cabinet FinishElectrostatically applied thermosetting polyester

Cylinder: 37" x 36" (94 x 91.4 cm) perforated galvanized steel with four baffles; 75 pounds (34.1 kg) dry weight (cotton load)

Motor: High Pressure Steam — 3/4 H.P. (Non-reversing models) Low Pressure Steam — 3/4 H.P. Both motors are lifetime lubricated, internal overload protected. (See below for reversing models.)

Boiler High Pressure Steam (6 Coil) — 4.60 BPH Horsepower: (154,100 BTU/hr., 72.1 kg/hr., 38,833 kCal/hr.)

Low Pressure Steam (4 Coil) — 4.00 BHP

(134,000 BTU/hr., 62.7 kg/hr., 33,768 kCal/hr.)

Electrical Requirements: Low Pressure — 230 Volt, 50 Hertz, 1 Phase, 8.5 Amp (See nameplate for voltage of your tumbler) High Pressure — 230 Volt, 50 Hertz, 1 Phase, 9.0 Amp

Air Flow: Low Pressure — 950 C.F.M. at 0.5" W.C. (449 liters/sec at 1.25 mBar) High Pressure — 900 C.F.M. at 0.5" W.C. (425 liters/sec at 1.25 mBar)

Net Weight615 Pounds (280 kg) (approx.)

REVERSING MOTOR SIZES

STEAM

GAS ELECTRIC

HIGH PRESSURE LOW PRESSURE

75 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.

CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

Page 33 of the Speed Queen JC50CE user manual — LAYOUT
Page 33 · click to enlarge
Page 33

SECTION II Installation Instructions

RECEIVING INSPECTION

Upon delivery, visually inspect crate carton and parts for any visible shipping damage. If crate, carton or cover are damaged or signs of possible damage are evident, have carrier note condition on shipping papers before shipping receipt is signed, or advise carrier of condition as soon as it is discovered.

Advise carrier of any damaged or missing articles as soon as possible. A written claim should be filed with carrier immediately if articles are damaged or missing.

Remove crate and protective cover as soon as possible and check items listed on packing list.

MATERIALS REQUIRED (Obtain Locally)

GAS, ELECTRIC OR STEAM DRYING TUMBLERS

  • Two steam shut-off gate valves for each condensate return line.
  • Flexible steam hoses with a 125 psig (pounds per square inch gauge) (8.79 kg/sq. cm) working pressure for connecting steam coils, Figures 24 and 25.
  • One circuit breaker.

GAS DRYING TUMBLERS ONLY

  • One gas shut-off valve for gas service line to each tumbler.
  • Two steam traps for steam coil outlet to condensate return line.
  • One steam pressure relief valve rated at 125 psig. (8.79 kg/cm 2 ).

STEAM DRYING TUMBLERS ONLY

  • One steam shut-off gate valve for steam service line to be connected upstream of solenoid steam valve.

FACILITIES REQUIRED

FLOOR

Construction must not block airflow at top rear of tumbler. Doing so would prevent adequate air supply to tumbler’s combustion chamber.

Drying tumbler may be installed on any level floor capable of supporting 100 pounds per square foot (488 kg/m2). Floor covering materials such as carpeting or tile should be removed.

VENTING

For maximum efficiency and minimum lint accumulation, tumbler air must be exhausted to outdoors by shortest possible route.

LAYOUT

Whenever possible, tumbler should be installed along an outside wall where duct length can be kept to a minimum, and make-up air can be easily accessed.

Page 34 of the Speed Queen JC50CE user manual — DUCT DIAMETER
Page 34 · click to enlarge
Page 34

Proper sized exhaust ducts are essential for proper operation. All elbows should be sweep type. Do not install elbows with a radius less than shown in table below. Exhaust ducts must be assembled so interior surfaces are smooth to reduce accumulation of lint. Do not use sheet metal screws to join vent sections. Improperly sized or assembled ductwork causes excess back pressure which results in slow drying, lint collecting in duct, lint blowing back into room, and increased fire hazard.

With tumbler in operation, airflow at any point in duct must be at least 1200 feet (366 m) per minute to insure that lint remains airborne.

  • Collector Venting While it is preferable to exhaust tumblers individually to outdoors, a main collector duct may be used if it is sized according to Figure 3.

Exhaust ducts shall be constructed of sheet metal or other noncombustible material. Such ducts must be equivalent in strength and corrosion resistance to ducts made of galvanized sheet steel not less than 0.0195 inches (0.495 mm) thick.

Collector duct may be rectangular in cross section, as long as area is not reduced. Provisions should be made for lint removal and cleaning of collector duct.

Where exhaust duct pierces a combustible wall or ceiling, an opening having a diameter of 4 inches (10.2 cm) larger than diameter of exhaust duct shall be provided, with duct centered in opening. When ducts pass through walls, ceilings, floors or partitions, space around the duct shall be sealed with non- combustible material. See Figures 1, 2 and 3.

Collector duct must be tapered, as shown in Figure 3. Individual tumbler ducts must enter the collector duct at a 45° angle in direction of air flow. Never connect a tumbler duct at a 90° angle to collector duct. Doing so will cause excessive back pressure, resulting in poor performance. Never connect two tumbler exhaust ducts directly across from each other at point of entry to collector duct.

  • Individual Venting For maximum efficiency and performance, it is preferred to exhaust tumbler(s) individually to outdoors. At no point may cross area of installed venting be less than cross area of exhaust thimble of tumbler.

Collector system must be designed so static back pressure measured 12 inches (30.5 cm) from exhaust thimble does not exceed maximum allowable pressure specified on installation sticker on rear of tumbler. Measured with all tumblers running that are vented into collector.

Maximum allowable length of venting is 14 feet (4.3 m) and two 90° elbows or equivalent. If equivalent length of a duct required for an installation exceeds maximum allowable equivalent length, diameter of a round duct must be increased by 10% for each additional 20 feet (6.1 m). Cross section area of a rectangular duct must be increased by 20% for each additional 20 feet (6.1 m). Table below shows how to determine equivalent venting:

MAKE-UP AIR

A tumbler is forced air exhausted and requires provisions for make-up air to replace the air exhausted by tumbler.

Manufacturer’s recommended make-up air opening for each tumbler is 144 square inches (928 sq. cm) for 30 and 50 pound tumblers and 195 square inches (1258 sq. cm) for 75 pound tumblers. At a minimum, tumblers must have at least 1 in2 (2.54 cm2) of opening for every 1000 BTU/hr (252 Kcal/hr) of input rating for proper combustion.

DUCT DIAMETER

EQUIVALENT LENGTH OF

STRAIGHT DUCT

6" (15.2 cm) 8" (20.3 cm) 10" (25.4 cm) 12" (30.5 cm)

One 90° elbow = 7' (2.1 m) One 90° elbow = 9.3' (2.83 m) One 90° elbow = 11.6' (3.5 m) One 90° elbow = 14' (4.3 m)

ExampleA tumbler with a rated input of 120,000

BTU/hr (30,240 Kcal) requires 120 in2 (774 cm2) of free opening.

Equivalent Length (feet) (m) = 1.17 x Duct Diameter (inches) (cm)

Protective louvers in opening to outdoors can reduce air movement by approximately 40%. Opening must compensate for area taken up by louvers.

Make-up air openings for a room containing tumbler(s) and/or gas fired hot water heater or other gravity vented appliances must be increased sufficiently to prevent downdrafts in any vents when all tumblers are in operation. Do not locate gravity vented appliances between tumbler(s) and make-up air openings. If it is necessary to duct make-up air to tumbler(s), increase area of work by 25% to compensate for any restriction in air movement.

ExampleA 6-inch (15.2 cm) diameter duct’s

equivalent length of 14 feet (4.3 m) of duct and two 90° elbows is:

= 14 feet (4.3 m) + (2) 90° elbows = 14 feet (4.3 m) + 7 feet (2.1 m) + 7 feet (2.1 m) = 28 feet (8.5 m)

Equivalent length

Page 35 of the Speed Queen JC50CE user manual — T108IE3A
Page 35 · click to enlarge
Page 35

WARNING

WARNING WARNING WARNING WARNING WARNING

Solvent gases and vapors from dry cleaning machines create acids when drawn through the heater of a drying tumbler. These acids are corrosive to the drying tumbler as well as to the laundry load being dried. Be sure make-up air is free of solvent gases and vapors.

To reduce the risk of fire and accumulation of combustible gases, DO NOT exhaust tumbler air into a window well, gas vent, chimney or enclosed, unventilated area such as an attic wall, ceiling, crawl space under a building, or concealed space of a building.

If the dry cleaning machines are in the same area as the tumbler, then the tumbler make-up air must come from a source free of solvent gases and vapors.

FOR BEST PERFORMANCE Provide an individual exhaust duct for each tumbler. Do not install a hot water heater in room containing tumblers. It is better to have the water heater in a separate room with a separate air inlet.

ROOF 30" (76.2 CM)

T075IE3A

ROOF 30" (76.2 cm)

CEILING

WALL

REMOVABLE STRIP OF PANEL IN FRAMING WALL TO PERMIT REMOVAL OF TUMBLER FROM FRAMING WALL

36 INCHES (91.4 cm) RECOMMENDED

PARTITION OR

BULKHEAD

SERVICE AREA

24 INCHES (61.0 cm) MINIMUM

ONE TUMBLER

T108IE3B

TWO TUMBLERS

CONSULT YOUR LOCAL BUILDING CODE FOR REGULATIONS WHICH MAY ALSO APPLY

T108IE3A

THREE TUMBLERS

Page 36 of the Speed Queen JC50CE user manual — NO SCREEN
Page 36 · click to enlarge
Page 36
Speed Queen JC50CE — SECTION II Installation Instructions diagram (page 36)
Fig. 6 · SECTION II Installation Instructions

INSPECTION OR CLEANOUT COVER

WALL

A L K J I H G F E D C B

2" (5.1 cm) MINIMUM

NO SCREEN

T056IE3B

OR CAP

AIR OUT

MINIMUM DIAMETER

MINIMUM DIAMETER

DUCT STATION

DUCT STATION

*GAS ELECTRIC STEAM *GAS ELECTRIC STEAM

A 9" (22.9 cm) 10" (25.4 cm) G 23" (58.4 cm) 26" (66 cm)

B 12" (30.5 cm) 14" (35.6 cm) H 25" (63.5 cm) 28" (71.1 cm)

C 15" (38.1 cm) 17" (43.2 cm) I 26" (66 cm) 30" (76.2 cm)

D 17" (43.2 cm) 20" (50.8 cm) J 27" (68.6 cm) 31" (78 cm)

E 19" (48.3 cm) 22" (55.9 cm) K 29" (73.9 cm) 33" (83.8 cm)

F 21" (53.3 cm) 24" (61 cm) L 30" (76.2 cm) 34" (86.4 cm)

45˚

Page 37 of the Speed Queen JC50CE user manual — GROUNDING INSTRUCTIONS
Page 37 · click to enlarge
Page 37

ELECTRICAL REQUIREMENTS For 30 Pound (13 kg) Narrow Cabinet Tumblers

REQUIREMENTS

Speed Queen JC50CE — REQUIREMENTS diagram (page 37)
Fig. 7

Heat Source Electrical Specs Wires Required and Terminal Block Connection

Electric 230-50-3 L1 L2 L3 Ground to PE Busbar

Electric 380-50-3 L1 L2 L3 Ground to PE Busbar

Electric 415-50-3 L1 L2 L3 Ground to PE Busbar

GAS DRYING TUMBLERS

Speed Queen JC50CE — GAS DRYING TUMBLERS diagram (page 37)
Fig. 8

240V, 1 Phase, 50 Hz. 120V, 1 Phase, 30 Hz.

Minimum Wire Size 14 AWG (2.081 mm²) 14 AWG (2.081 mm²)

ELECTRIC DRYING TUMBLERS

Speed Queen JC50CE — ELECTRIC DRYING TUMBLERS diagram (page 37)
Fig. 9

240V 50 Hz. 1 Ph 240V 50 Hz. 3 Ph 380V 50 Hz. 3 Ph 415V 50 Hz. 3 Ph

Amp Rating 91 Amp 55 Amp 34 Amp 31 Amp

Circuit Breaker 100 Amp 60 Amp 40 Amp 35 Amp

Minimum Wire Size 2 AWG (33.63 mm²) 6 AWG (13.32 mm²) 8 AWG (8.366 mm²) 8 AWG (8.366 mm²)

GROUNDING INSTRUCTIONS

Drying tumbler must be grounded. In event of malfunction or breakdown, grounding will reduce risk of electric shock by providing a path of least resistance for electric current. Drying tumbler must be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with circuit conductors and connected to PE Busbar.

Speed Queen JC50CE — GROUNDING INSTRUCTIONS diagram (page 37)
Fig. 10

To reduce the risk of fire and electric shock, check with a qualified serviceman for proper grounding procedures. Improper connection of the equipment grounding conductor can result in a risk of electric shock.

To reduce the risk of fire and electric shock, if electrical supply is coming from a three phase service, DO NOT connect a “Stinger Leg” to a single phase machine.

Page 38 of the Speed Queen JC50CE user manual — ELECTRIC DRYING TUMBLERS
Page 38 · click to enlarge
Page 38

ELECTRICAL REQUIREMENTS For 30 Pound (13 kg) Tumblers

REQUIREMENTS

Speed Queen JC50CE — REQUIREMENTS diagram (page 38)
Fig. 11

Heat Source Electrical Specs Wires Required and Terminal Block Connection

Gas & Steam 230/50/1 L1 L2 Ground to PE Busbar

Electric 380/50/3 L1 L2 L3 Ground to PE Busbar

Electric 415/50/3 L1 L2 L3 Ground to PE Busbar

Steam 380/50/3 L1 L2 L3 Ground to PE Busbar

GAS AND HIGH PRESSURE STEAM DRYING TUMBLERS

Speed Queen JC50CE — GAS AND HIGH PRESSURE STEAM DRYING TUMBLERS diagram (page 38)
Fig. 12

240 V, 1 Phase, 50 Hz. 380 V, 3 Phase, 50 Hz.

Minimum Wire Size 14 AWG (2.081 mm²) 14 AWG (2.081 mm²)

ELECTRIC DRYING TUMBLERS

Speed Queen JC50CE — ELECTRIC DRYING TUMBLERS diagram (page 38)
Fig. 13

240 V, 1 Ph, 50 Hz. 240 V, 3 Ph, 50 Hz. 380 V, 3 Ph, 50 Hz. 415 V, 3 Ph, 50 Hz.

Minimum Wire Size 2 AWG (33.63 mm²) 6 AWG (13.32 mm²) 8 AWG (8.366 mm²) 8 AWG (8.366 mm²)

AMP Rating 90 Amp 54 Amp 33 Amp 30 Amp

Circuit Breaker 100 Amp 60 Amp 40 Amp 35 Amp

Page 39 of the Speed Queen JC50CE user manual — WARNING
Page 39 · click to enlarge
Page 39

30 Pound (13 kg) Tumblers

LOW STEAM DRYING TUMBLERS

LOW PRESSURE STEAM DRYING TUMBLERS

240 V, 1 Phase 50 Hz.

Minimum Wire Size 16 AWG (1.309 mm²)

Circuit Breaker 20 AMP

GROUNDING INSTRUCTIONS

Drying tumbler must be grounded. In event of malfunction or breakdown, grounding will reduce risk of electric shock by providing a path of least resistance for electric current. Drying tumbler must be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with circuit conductors and connected to PE Busbar.

WARNING

To reduce the risk of fire and electric shock, check with a qualified serviceman for proper grounding procedures. Improper connection of the equipment grounding conductor may result in a risk of electric shock.

WARNING

To reduce the risk of fire and electric shock, if electrical supply is coming from a three phase service, DO NOT connect a “Stinger Leg” to a single phase machine.

Poles 2

Page 40 of the Speed Queen JC50CE user manual — ELECTRIC DRYING TUMBLERS
Page 40 · click to enlarge
Page 40

ELECTRICAL REQUIREMENTS For 50 Pound (22 kg) Tumblers

REQUIREMENTS

Speed Queen JC50CE — REQUIREMENTS diagram (page 40)
Fig. 14

Heat Source Electrical Specs Wires Required and Terminal Block Connection

Gas & Steam 230/50/1 L1 L2 Ground to PE Busbar

Steam 380-415/50/3 L1 L2 L3 Ground to PE Busbar

Electric 380-415/50/3 L1 L2 L3 Ground to PE Busbar

Gas & Steam 230/50/1 L1 L2 Ground to PE Busbar

Gas & Steam 380-415/50/3 L1 L2 L3 Ground to PE Busbar

Electric 230/50/3 L1 L2 L3 Ground to PE Busbar

Electric 380-415/50/3 L1 L2 L3 Ground to PE Busbar

GAS AND HIGH PRESSURE STEAM DRYING TUMBLER

Speed Queen JC50CE — GAS AND HIGH PRESSURE STEAM DRYING TUMBLER diagram (page 40)
Fig. 15

208V / 240 V 1 Phase, 50 Hz. 208 / 240 V 3 Phase, 50 Hz. 380 / 415 V 3 Phase, 50 Hz.

Minimum Wire Size 14 AWG (2.081 mm²) 14 AWG (2.081 mm²) 14 AWG (2.081 mm²)

ELECTRIC DRYING TUMBLERS

Speed Queen JC50CE — ELECTRIC DRYING TUMBLERS diagram (page 40)
Fig. 16

240 V, 3 Phase 50 Hz. 380 V, 3 Phase 50 Hz. 415 V, 3 Phase 50 Hz.

Minimum Wire Size 3 AWG (26.67 mm²) 6 AWG (13.32 mm²) 6 AWG (13.32 mm²)

Page 41 of the Speed Queen JC50CE user manual — GROUNDING INSTRUCTIONS
Page 41 · click to enlarge
Page 41

50 Pound (22 kg) Tumblers

LOW PRESSURE STEAM DRYING TUMBLERS

LOW PRESSURE STEAM DRYING TUMBLERS

240 V 1 Phase, 50 Hz.

Minimum Wire Size 14 AWG (2.081 mm²)

Circuit Breaker 15 AMP

GROUNDING INSTRUCTIONS

Drying tumbler must be grounded. In event of malfunction or breakdown, grounding will reduce risk of electric shock by providing a path of least resistance for electric current. Drying tumbler must be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with circuit conductors and connected to the PE Busbar.

WARNING To reduce the risk of fire and electric shock, check with a qualified service technician for proper grounding procedures. Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Poles 2

Page 42 of the Speed Queen JC50CE user manual — ELECTRIC DRYING TUMBLERS
Page 42 · click to enlarge
Page 42

ELECTRICAL REQUIREMENTS For 75 Pound (34 kg) Tumblers

REQUIREMENTS

Speed Queen JC50CE — REQUIREMENTS diagram (page 42)
Fig. 17

Heat Source Electrical Specs Wires Required and Terminal Block Connection

Gas & Steam 230/50/1 L1 L2 Ground to PE Busbar

Electric 208-230/50-60/3 L1 L2 L3 Ground to PE Busbar

Electric 380/50/3 L1 L2 L3 Ground to PE Busbar

Electric 415/50/3 L1 L2 L3 Ground to PE Busbar

Steam 380/50/3 L1 L2 L3 Ground to PE Busbar

GAS AND HIGH PRESSURE STEAM DRYING TUMBLERS

Speed Queen JC50CE — GAS AND HIGH PRESSURE STEAM DRYING TUMBLERS diagram (page 42)
Fig. 18

208V / 240 V 1 Phase, 50 Hz. 208 / 240 V 3 Phase, 50 Hz. 380 / 415 V 3 Phase, 50 Hz.

Minimum Wire Size 14 AWG (2.081 mm²) 14 AWG (2.081 mm²) 14 AWG (2.081 mm²)

ELECTRIC DRYING TUMBLERS

Speed Queen JC50CE — ELECTRIC DRYING TUMBLERS diagram (page 42)
Fig. 19

380 V, 3 Ph, 50 Hz. 415 V, 3 Ph, 50 Hz.

Minimum Wire Size 6 AWG (13.32 mm²) 6 AWG (13.32 mm²)

GROUNDING INSTRUCTIONS Drying tumbler must be grounded. In event of malfunction or breakdown. Grounding will reduce risk of electric shock by providing a path of least resistance for electric current. Drying tumbler must be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with circuit conductors and connected to PE Busbar.

Speed Queen JC50CE — ELECTRIC DRYING TUMBLERS diagram (page 42)
Fig. 20

To reduce the risk of fire and electric shock, check with a qualified service technician for proper ground procedures. Improper connection of the equipment grounding conductor may result in risk of electric shock.

To reduce the risk of fire and electric shock, if electrical supply is coming from a three phase service, DO NOT connect a “Stinger Leg” to a single phase machine.

Page 43 of the Speed Queen JC50CE user manual — ELECTRICAL CONNECTIONS
Page 43 · click to enlarge
Page 43

ELECTRICAL CONNECTIONS

Speed Queen JC50CE — ELECTRICAL CONNECTIONS diagram (page 43)
Fig. 21
Speed Queen JC50CE — ELECTRICAL CONNECTIONS diagram (page 43)
Fig. 22

All electrical connections should be made by a qualified electrician.

To reduce the risk of electrical shock, de-energize the electrical circuit being connected to the tumbler before mak- ing any electrical connections. Never attempt to connect a live circuit.

Use the following steps to connect electrical service to the tumbler:

1. Install a circuit breaker, as close to tumbler as possible. If more than one tumbler is being installed, a circuit breaker should be provided for each tumbler. This will make it possible to disconnect each tumbler for maintenance purposes.
2. a. Connect conduit-encased leads to circuit
Speed Queen JC50CE — ELECTRICAL CONNECTIONS diagram (page 43)
Fig. 23

breaker. b. Turn “off” disconnect switch on tumbler and

open junction box. c. Insert conduit-encased leads through

one of the knockout holes in junction box. d. Connect wire leads to disconnect switch.

1 Phase Units: Connect one lead to top left connection point. Connect other lead to top right connection point.

3 Phase Units: Connect one lead to each connection point.

e. Connect a ground wire to PE Busbar,

Figure 19, in junction box.

3. Check electrical service phase sequence (three phase only) as follows:

a. Energize electrical service and momentarily

start tumbler. Check direction of the cylinder rotation. If cylinder rotates clockwise (viewed from front), phase sequence is correct. If cylinder rotates counterclockwise, proceed with step “b”. b. Disconnect and reverse any two leads at

connections.

4. Close junction box cover and turn “on” disconnect

switch.

Page 44 of the Speed Queen JC50CE user manual — WARNING
Page 44 · click to enlarge
Page 44

POSITIONING DRYING TUMBLER

Tumbler may be removed from skid before moving to installation location or moved while still attached to skid. Remove tumbler from skid by unscrewing four shipping capscrews (one at each corner) and remove tumbler from skid. Lint panel door will have to be removed in order to remove two front capscrews.

Screw four leveling legs back into level adjusting fittings from top. Slide tumbler to its permanent location and level. Keep tumbler as close to floor as possible. All four legs must rest firmly on floor so weight of tumbler is evenly distributed. Tumbler must not rock.

LEVELING DRYING TUMBLER

Each tumbler should be leveled within ¹⁄₈ inch (3.2 mm) from front to rear, and ¹⁄₈ inch (3.2 mm) from side to side. Check front to rear level by rotating clothes cylinder until one rib is at bottom, then place a

level on bottom rib. Side to side level should be checked by placing a level on front and rear of top panel.

GAS REQUIREMENTS (Gas Drying Tumblers)

To reduce the risk of fire or explosion, if the tumbler is to be connected to Liquefied Petroleum (L.P.) gas, a vent to the outdoors must be provided in the room where the tumbler is installed.

WARNING

Size of gas service pipe is dependent upon many variables (lengths, tees, etc.). Specific pipe size information should be obtained from gas supplier. Refer to table in Figure 22 for general pipe size data.

It is important that equal gas pressure be maintained at all tumbler gas connections. This can best be done by installing a one inch pipe gas loop as shown in Figures 20 and 21.

Page 45 of the Speed Queen JC50CE user manual — Example of Gas Supply Piping
Page 45 · click to enlarge
Page 45

Example of Gas Loop Piping

GAS SPACE HEATER

MAIN REGULATOR

TUMBLERS

GAS SHUT-OFF

VALVES

GAS LINE PRESSURE TAP

ONE INCH

GAS METER

(2.54 cm)

GAS WATER

PIPE GAS LOOP NOTEMinimum pipe size to

HEATERS

PRESSURE REGULATOR

tumbler is 1/2" (1.27 cm)

T034IE3D

An in-line pressure regulator may be required on Natural Gas models if the line pressure exceeds eight water column inches (2.00 kPa) pressure with all gas appliances firing.

Example of Gas Supply Piping

Speed Queen JC50CE — Example of Gas Supply Piping diagram (page 45)
Fig. 24 · Example of Gas Supply Piping

1 2 3 4 5 6 7 8 9

SAMPLE CALCULATIONS: Equivalent Length = Total length of main gas supply pipe from the gas meter to the far end of the tumbler dryers. = 25' + 19' (7.6 m + 5.8 m) gas supply pipe. = 44' (13.4 m) Total Gas Liner

Total BTU/HR = The sum of the BTU/HR. of all tumblers being fed by the main gas supply pipe. = 9 x 75,000 = 675,000 BTU/HR.

Using the table in Figure 22, the main supply pipe diameter should be 2" (5.08 cm).

(If required)

Page 46 of the Speed Queen JC50CE user manual — GAS APPLIANCES
Page 46 · click to enlarge
Page 46

GAS PIPE SIZE REQUIRED FOR 1,000 BTU NATURAL GAS — .64 SPECIFIC GRAVITY

AT 6½ ± 1½ INCH WATER COLUMN PRESSURE (1.62 ± .37 kPa)

EQUIVALENT LENGTH

25 FT. (7.63 m)

50 FT. (15.25 m)

150 FT. (45.75 m) 75 FT. (22.88 m)

125 FT. (38.13 m) 100 FT. (30.50 m)

GAS APPLIANCES

TOTAL BTU/HR. (Kcal/hr)

BASED ON 0.3" WATER COLUMN (0.75 mBar) PRESSURE DROP FOR LENGTH GIVEN

³⁄₄" (1.905cm)

³⁄₄" (1.905cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

³⁄₄" (1.905cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

³⁄₄" (1.905cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

1¹⁄₄" (3.18cm)

³⁄₄" (1.905cm)

1" (2.54cm)

1" (2.54cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1" (2.54cm)

1" (2.54cm)

1" (2.54cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1" (2.54cm)

1" (2.54cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1¹⁄₂" (3.81cm)

1" (2.54cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1¹⁄₂" (3.81cm)

1¹⁄₂" (3.81cm)

1¹⁄₂" (3.81cm)

1¹⁄₄" (3.18cm)

1¹⁄₄" (3.18cm)

1¹⁄₂" (3.81cm)

1¹⁄₂" (3.81cm)

1¹⁄₂" (3.81cm)

2" (5.08cm)

1¹⁄₄" (3.18cm)

1¹⁄₂" (3.81cm)

1¹⁄₂" (3.81cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

1¹⁄₂" (3.81cm)

1¹⁄₂" (3.81cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

1¹⁄₂" (3.81cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

1¹⁄₂" (3.81cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2" (5.08cm)

2" (5.08cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2" (5.08cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2" (5.08cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

2" (5.08cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

2¹⁄₂” (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

2¹⁄₂" (6.35cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

3¹⁄₂" (8.89cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3" (7.62cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3" (7.62cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

2¹⁄₂" (6.35cm)

3" (7.62cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

3¹⁄₂" (8.89cm)

4" (10.16cm)

Show 29 more labels / short text on this page
100,000 (25,200) · 120,000 (30,240) · 140,000 (35,280) · 160,000 (40,320) · 180,000 (45,360) · 200,000 (50,400) · 300,000 (75,600) · 400,000 (100,800) · 500,000 (126,000) · 600,000 (151,200) · 700,000 (176,400) · 800,000 (201,600) · 900,000 (226,800) · 1,000,000 (252,000) · 1,100,000 (277,200) · 1,200,000 (302,400) · 1,300,000 (327,600) · 1,400,000 (352,800) · 1,500,000 (378,600) · 1,600,000 (403,200) · 1,700,000 (428,400) · 1,800,000 (453,600) · 1,900,000 (478,800) · 2,000,000 (504,000) · 2,200,000 (554,400) · 2,400,000 (604,800) · 2,600,000 (655,200) · 2,800,000 (705,600) · 3,000,000 (756,000)
Page 47 of the Speed Queen JC50CE user manual —  WARNING
Page 47 · click to enlarge
Page 47

GAS CONNECTIONS (Gas Drying Tumblers)

Before connecting gas piping to tumbler, make certain gas service is same as that specified on nameplate (near gas connection), Page 5.

Purge air and sediment from gas service line before connecting it loosely to tumbler. Purge remaining air until odor of gas is detected, then tighten connection. Use pipe compound, resistant to actions of L.P. gas, on all pipe threads.

NATURAL GAS service must be supplied at 6¹⁄₂ ± 1¹⁄₂ inch water column pressure (1.62 ± .37 kPa).

WARNING Check all pipe connections, internal and external, for gas leaks using a soapy solution. To reduce the risk of explosion or fire, DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS! Gas connections should be checked annually for leakage.

L.P. GAS service must be supplied at 11 ± .3 inch water column pressure (2.74 ± .07 kPa).

If gas service is not same as that specified, DO NOT CONNECT THE GAS LINE TO TUMBLER! It will first be necessary to convert gas burner orifice and gas valve.

WARNING

The tumbler and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.45 kPa).

The tumbler must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1/2 psig (3.45 kPa).

Page 48 of the Speed Queen JC50CE user manual — 0" CLEARANCE
Page 48 · click to enlarge
Page 48

DRYING TUMBLER ENCLOSURE CONSTRUCTION

WARNING

To reduce the risk of serious injury, install lockable doors to prevent public access to rear of tumblers.

A typical tumbler enclosure is shown in Figure 23. Note that enclosure does touch tumbler top and side panels. Note, too, minimum and maximum dimensions. Be aware that there may be local codes and ordinances which must be complied with.

12" (30.5 cm) MINIMUM CLEARANCE

4" (10.16 cm) MAXIMUM

GUARD

PROVISION

FOR MAKE-UP

AIR

T038IE3B

24" (61 cm) MINIMUM 36" (91.4 cm) RECOMMENDED

0" CLEARANCE

FOR MAINTENANCE

PURPOSES

Page 49 of the Speed Queen JC50CE user manual — INSTALLING STEAM SOLENOID VALVE AND MAKING STEAM INLET CONNECTIONS
Page 49 · click to enlarge
Page 49

STEAM REQUIREMENTS (Steam Drying Tumblers)

information should be obtained from the steam system supplier or a qualified steam fitter. Size of steam service pipe is dependent upon many variables (length, tees, high pressure system, low pressure system, etc.) Specific pipe size

STEAM CONNECTIONS (Steam Drying Tumblers)

INSTALLING STEAM SOLENOID VALVE AND MAKING STEAM INLET CONNECTIONS

INSTALLING STEAM TRAP AND MAKING CONDENSATE RETURN CONNECTIONS

Steam trap must be installed and coil outlet connections must be connected to condensate return lines. The following steps outline the procedure for installing steam trap and connecting condensate return lines. See Figure 24 for a typical installation.

High pressure machines require a (constant) 80 to 100 psig (5.62 to 7.03 kg/sq. cm) steam service for optimum operation. Low pressure machines require a (constant) 10 to 15 psig (.70 to 1.05 kg/sq. cm) steam service for optimum operation. The following steps outline procedure for installing steam solenoid valve and connecting steam service.

a. Connect a flexible hose to each steam coil outlet,

Figure 24. b. Install a strainer to the ends of each flexible hose. c. Install a steam trap to each strainer.

a. Install a manual shut-off gate valve in condensate

return line after steam trap for each coil.

b. Connect steam solenoid valve to related steam

coil inlet connection with nipples, flex hoses, unions, tee and pressure relief valve. See Figure 24 for a typical installation.

d. Install a gate shut-off valve to each steam trap. e. Connect to condensate return lines.

c. Install a gate shut-off valve in steam supply

line, Figure 24. Connect shut-off gate valve outlet to solenoid steam valve inlet connection.

The flexible steam hoses connecting the coil outlet connections and steam traps must have a minimum of 125 psig (pounds per square inch gauge) (8.79 kg/sq. cm.) working pressure. A shutoff gate valve must be installed downstream from each steam trap so the condensate return line can be isolated in event a steam trap requires maintenance.

The flexible steam hoses connecting the solenoid steam valve to the coil inlets must have a 125 psig (pounds per square inch gauge) (8.79 kg/sq. cm) working pressure. A shut-off gate valve must be installed upstream from the solenoid steam valve. This way, steam can be shut off for maintenance purposes, or in the event the hose ruptures.

Each steam trap must be supported so minimum load is exerted on the coil outlet connection.

The steam solenoid valve must be supported so minimum load is exerted on the steam coil inlet connections.

aWARNING · aWARNING

Page 50 of the Speed Queen JC50CE user manual — STEAM CONNECTIONS (Steam Drying Tumblers)
Page 50 · click to enlarge
Page 50

STEAM CONNECTIONS (Steam Drying Tumblers)

Speed Queen JC50CE — STEAM CONNECTIONS (Steam Drying Tumblers) diagram (page 50)
Fig. 25 · STEAM CONNECTIONS (Steam Drying Tumblers)
Speed Queen JC50CE — STEAM CONNECTIONS (Steam Drying Tumblers) diagram (page 50)
Fig. 26 · STEAM CONNECTIONS (Steam Drying Tumblers)
Page 51 of the Speed Queen JC50CE user manual — LIGHTING AND SHUTTING DOWN GAS IGNITION SYSTEM
Page 51 · click to enlarge
Page 51

LIGHTING AND SHUTTING DOWN GAS IGNITION SYSTEM

during first three seconds ignition control will “lockout” causing gas valve to close and a red button on ignition control to illuminate.

1. Turn machine disconnect switch, located on rear of tumbler, to the “on” position.

To reset ignition system , open access door and press red button on ignition control. Close and lock access door, verify that gas shut-off valve is in the “on” position and return to step three.

2. Turn gas shut-off valve, located on rear of tumbler, to the “on” position (gas valve handle should be parallel with gas line).
4. If tumbler will not start, remove it from service by turning machine disconnect switch, located on rear of tumbler, to the “off” position and turn the gas shut-off valve, located on rear of tumbler, to the “off” position (gas valve handle should be at a right angle to gas line).
3. Start tumbler, following operating instructions which accompanied it.

NOTE: Ignition control circuitry will verify airflow switch, located on rear of tumbler, is open before starting cylinder motor. Once cylinder motor is started, air flowing through tumbler will cause airflow switch to close. Tumbler will purge air from tumbler for 18 seconds. Ignition will start by a three second release of gas from gas valve and sparking of ignitor. If ignition does not occur

Speed Queen JC50CE — LIGHTING AND SHUTTING DOWN GAS IGNITION SYSTEM diagram (page 51)
Fig. 27
Page 52 of the Speed Queen JC50CE user manual — LINE UP NOTCH TO CLEAR RATCHET
Page 52 · click to enlarge
Page 52

ACCESSORY TIMING CAM INSTALLATION (Coin Meter Models)

REMOVAL OF EXISTING TIMING CAM

No. of Pins in Cam

1. Rotate cam by hand until "V" notch lines up beneath the ratchet tooth see Figure 28.
2. Insert narrow screwdriver under nylon cam, close to the clock shaft. Lift gently off shaft. Make sure that pressure is directed upward and that the "V" notch clears the ratchet tooth.

Cams that allow other timer increments are available through your distributor.

INSTALLATION OF NEW TIMING CAM

To figure time increments, use this formula: Timer Motor Speed (60) divided by number of pins on cam = Cycle Length (minutes). Cams are available with 1 to 12 pins.

1. Insert drive into timing cam with wide prong in wide hole of cam.
2. Position timing cam and drive fork over the timer shaft, aligning the timer flat with the drive fork and the "V" notch with one of the ratchet teeth.

Example: 60 ÷ 5 (Pin cam) = 12 minute cycle.

3. Press timing cam down firmly to seat timing cam onto the motor shaft.

LINE UP NOTCH TO CLEAR RATCHET

TOOTH

LIFT GENTLY WITH NARROW

BLADE

T039IE1A

4. Remove all accumulated time by turning cam counterclockwise until switch shuts off. Apply moderate clockwise pressure to fully seated timing cam and drive against the timing motor shaft. Meter must be advanced electrically for one cycle before an accurate measure of time can be made.

Cycle Length (Minutes) · 10 12 15

Page 53 of the Speed Queen JC50CE user manual — Electronic Control Tumbler
Page 53 · click to enlarge
Page 53

PRELIMINARY OPERATING CHECKS

1. Remove or open all panels and inspect accessible bolts, nuts, screws, terminals and fittings for security.
6. Load tumbler with clothes or clean rags.
7. Start tumbler and check burner flame, adjust gas inlet shutter if necessary (refer to Adjustment Section).
2. Check belt tension, adjust if necessary (refer to Adjustment Section).
8. Check air flow switch operation by opening lint panel. Heating system should shut off when lint panel is opened approximately 1-1/2" (3.81 cm). Adjust if necessary (refer to Adjustment Section).
3. Energize electrical circuit to tumbler circuit breaker and turn on tumbler disconnect switch.
4. Turn on gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be parallel with gas supply line when in “ON” position.
9. Turn off tumbler.

10.Check air flow switch operation by opening lint panel. Heating systems should shut off when lint panel is opened approximately 6" (15.24 cm) with a full load.

5. Press and hold in Push-to-Start Button for approximately three (3) seconds. Release button and open cylinder door. Cylinder should stop rotating within seven (7) seconds after door is opened 3" (7.5 cm) plus or minus 1/4" (0.635 cm). If cylinder does not stop rotating, adjust cylinder door interlock (refer to Adjustment Section).

FINAL OPERATING CHECKS

Manual Dual Timer Tumbler

Coin Operated Tumbler

1. Set temperature selector to HIGH and set drying and cool down selectors to their maximum settings.
1. Set temperature selector to HIGH.
2. Insert required amount of coins.
2. Press and hold in Push-to-Start Button for approximately three (3) seconds. Motor will start, heat system will turn on, drying indicator will light and drying selector will rotate counterclockwise.
3. Press and hold in Push-to-Start Button for approximately three (3) seconds. Motor will start and heat system will turn on.
4. Near end of cycle a preset 2 1/2 minute cool down cycle will start.
3. When drying selector reaches zero (0) heat system will shut off, drying indicator will turn off, cooling indicator will light and cooling selector will rotate counterclockwise.
5. When metered time expires, motor will stop indicating drying cycle is finished.
4. When cooling selector reaches zero (0) motor will stop and cooling indicator will turn off indicating drying cycle is finished.

Electronic Control Tumbler

Tumbler comes equipped with Electronic Control. Electronic Control gives owner a variety of programming options. To learn how to use Electronic Control, consult supplemental manual.

Page 54 of the Speed Queen JC50CE user manual — NOTES
Page 54 · click to enlarge
Page 54

NOTES

Page 55 of the Speed Queen JC50CE user manual — PROPER AIR FLOW
Page 55 · click to enlarge
Page 55

SECTION III Adjustments

MAIN GAS BURNER AIR SHUTTER (All Gas Models)

5. After air shutter is adjusted for proper flame, tighten air shutter adjusting screw securely. Control panel may have to be removed temporarily to loosen air shutter screws to turn shutter.
6. If shutter is correctly adjusted, but flame pattern is straight up, (Figure 29), insufficient primary air is flowing through tumbler and airflow switch is improperly set. A flame pattern that flares to right and left (Figure 29) indicates no air is flowing through tumbler.

Air shutter adjustments will vary from location to location and will depend on vent system, number of units installed, make-up air and line gas pressure. Opening shutter increases amount of primary air supplied to burner while closing shutter decreases primary air supply. Adjust air shutter as follows:

AIR FLOW SWITCH (Gas and Electric Models, see Figure 30)

Air flow switch is set at factory for proper operation. Steam models do not have an air flow switch. However, if there is a problem with airflow switch, it should be adjusted as follows:

1. Unlock and open access door.
2. Start tumbler and check flame pattern. Correct air and gas mixture is indicated if flame pattern is primarily blue, with small yellow tips, and bends to right of heater section. (See Figure 29.) Too little air is indicated if flame is yellow, lazy and smokey.
3. To adjust air shutter, loosen air inlet shutter adjusting screw, see Figure 29.
4. Open or close air shutter as necessary to obtain proper flame intensity.

PROPER AIR FLOW

INSUFFICIENT

NO AIR FLOW

AIR FLOW

T047SE3A T048SE3A T049SE3A

AIR SHUTTER

AIR SHUTTER

AIR SHUTTER

ADJUSTING

ADJUSTING

ADJUSTING

SCREWS

SCREWS

SCREWS

Page 56 of the Speed Queen JC50CE user manual — SECTION II Installation Instructions
Page 56 · click to enlarge
Page 56

Electric Models: If switch remains open, or pops open and closed during cycle, heating system will shut off. Cylinder and fan will continue to operate even though air flow switch is malfunctioning.

Counterweight should be adjusted so air flow will force disc away from cabinet when lint panel is opened 6 inches (15.24 cm) with a full load. Adjust air flow switch as follows:

1. Load tumbler.

Gas Models: If switch remains open, entire unit will shut down when Push-to-start button is released. Once tumbler starts and continues to run, a loss of air flow, air flow switch jams or a bouncing air flow switch will shut entire tumbler down.

2. Start tumbler. Open lint panel 6 inches (15.24 cm). Airflow disc should move away from cabinet, opening switch contacts and shutting off heat system. This indicates proper operation and proper adjustment.
Speed Queen JC50CE — SECTION II Installation Instructions diagram (page 56)
Fig. 28 · SECTION II Installation Instructions

To reduce the risk of fire, air flow switch operation may be affected by a clogged lint screen, lack of make-up air, obstructions in the vertical recirculation stack or in the customer installed main or collector ducts. These conditions must be checked and necessary corrections made before adjusting air flow switch. Always adjust air flow at installation.

3. If switch is not opening as described in step “2”, it should be adjusted so it is MORE sensitive. Depress spring clip and move counterweight toward disc. Retest by opening lint panel and continue moving counterweight toward disc until switch operates as described in step “2”.
4. If switch opens BEFORE lint panel is opened proper distance, step “2”, it should be adjusted so it is LESS sensitive. Depress spring clip and move counterweight away from disc. Retest by opening lint panel and continue moving counterweight away from disc until switch operates as described in step “2”.

Air flow switch operation is controlled by counter- weight position on shaft. Moving counterweight either increases or decreases air flow switch sensitivity.

Speed Queen JC50CE — SECTION II Installation Instructions diagram (page 56)
Fig. 29 · SECTION II Installation Instructions
Page 57 of the Speed Queen JC50CE user manual — ACORN
Page 57 · click to enlarge
Page 57

LOADING DOOR SWITCH

CYLINDER DOOR STRIKE

Loading door switch turns off tumbler any time loading door is opened. To adjust loading door switch, follow these steps:

The door strike must be adjusted to have sufficient tension to hold loading door closed against force of load tumbling against it. Proper adjustment is when 8 to 15 pounds (35.6 N - 66.7 N) pull is required to open door.

1. Start tumbler following operating instructions which accompanied it.

To adjust, open door, loosen jamnut and turn door strike screw in or out as required. Retighten jamnut.

2. Slowly open loading door. Cylinder and heating system should stop when door is open 3" (7.5 cm) plus or minus 1/4" (0.635 cm).
3. Slowly close loading door. Loading door switch should close with an audible “click” when loading door is closed 3" (7.5 cm) plus or minus 1/4" (0.635 cm).

DOOR STRIKE

4. If loading door switch does not close when loading door is closed 3" (7.5 cm) plus or minus 1/4" (0.635 cm): a. Close loading door completely. b. Loosen lower screw on switch coupler and

rotate switch coupler COUNTERCLOCKWISE until it stops. c. Tighten lower screw on switch coupler. d. Return to step 1 to verify loading door switch

operation.

ACORN

NUT

LOADING

DOOR LATCH

DOOR SWITCH

SWITCH COUPLER

T048IE1A

T275IE1A

Page 58 of the Speed Queen JC50CE user manual — DRIVE V-BELT
Page 58 · click to enlarge
Page 58

DRIVE V-BELT

2. To adjust belt tension, loosen adjusting bolt holding idler housing assembly to housing support.
Speed Queen JC50CE — DRIVE V-BELT diagram (page 58)
Fig. 30

To reduce the risk of serious injury or death, disconnect power to the tumbler before performing this operation.

3. To tighten V-belt: a. Loosen lower nut on adjusting bolt. b. Turn bolt up until belt has proper tension. c. Tighten upper and lower nut or adjusting bolt.

Proper tension is when belt can be depressed approximately ¹⁄₂ inch (1.27 cm) by applying light thumb pressure at a point midway between the sheave and motor pulley.

4. To loosen V-belt: a. Loosen top nut on adjusting bolt. b. Turn bolt down until belt has proper tension. c. Tighten upper and lower nut or adjusting bolt.
1. Remove guard from rear of tumbler.
Speed Queen JC50CE — DRIVE V-BELT diagram (page 58)
Fig. 31
5. Replace guard on rear of tumbler.

To reduce the risk of serious injury or death, guard MUST be installed on rear of tumbler after belt adjustment is made.

6. Upper belt requires no adjustment since it is selfadjusting.
Speed Queen JC50CE — DRIVE V-BELT diagram (page 58)
Fig. 32
Page 59 of the Speed Queen JC50CE user manual — WARNING
Page 59 · click to enlarge
Page 59

SECTION IV Preventive Maintenance Instructions

DAILY

6. Ensure lint screen covers entire opening in lint screen hood. Gaps between lint screen and lint screen hood allows lint to flow into ductwork system restricting air circulation.
1. Make certain drying cycle has ended.
2. Open loading door.
3. Unlock and remove lint panel.
7. Wipe any accumulated lint off thermostat sensing probe. Lint buildup on sensing probe will cause overheating of tumbler.
4. Remove accumulated lint in lint compartment. Lint left in lint compartment will be drawn back onto lint screen and restrict air circulation.
8. Replace and securely lock lint panel.
5. Clean lint from lint screen. If lint screen is torn replace immediately. A torn lint screen allows lint to flow into ductwork system restricting air circulation.

WARNING

THERMOSTAT SENSING PROBE

LINT SCREEN

T046IE3A

MONTHLY

1. Perform daily cleaning of accumulated lint.
6. Remove bottom cover from vertical exhaust duct and clean out all accumulated lint.
2. Deactivate electrical circuit by turning off electrical disconnect switch on rear of tumbler.
7. Reinstall vertical exhaust duct cover.
4. Remove exhaust duct from rear of tumbler and clean out all accumulated lint.
8. Inspect entire duct work assembly and clean out all accumulated lint.
5. Reinstall exhaust duct.
9. Energize electrical circuit to tumbler by turning on electrical disconnect switch on rear of tumbler.
Page 60 of the Speed Queen JC50CE user manual — Biannually
Page 60 · click to enlarge
Page 60

Quarterly

1. Deactivate electrical circuit by turning off disconnect switch on rear of tumbler.
6. Remove screws holding rear drive guard to back of tumbler.
2. Perform daily cleaning of accumulated lint.
7. Inspect belts for wear and proper tension (refer to Adjustments section).
3. Perform monthly inspection and cleaning of accumulated lint.
8. Reinstall rear drive guard to back of tumbler.
4. Clean accumulated lint and other debris from front and back motor air vents.
9. Energize electrical circuit to tumbler by turning on electrical disconnect switch on rear of tumbler.
5. Shut off gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be at 90 0 angle to gas supply line when in “OFF” position.
10. Turn on gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be parallel with gas supply line when in “ON” position.

Biannually

1. Deactivate electrical circuit by turning off disconnect switch on rear of tumbler.
2. Perform daily cleaning of accumulated lint.
8. Close and securely lock service panel.
3. Perform monthly inspection and cleaning of accumulated lint.
9. Open electrical junction box cover and inspect all electrical and grounding connections for security. Tighten any loose electrical connections.
4. Perform quarterly inspection and cleaning of accumulated lint.
10. Close electrical junction box cover and energize electrical circuit to tumbler by turning on electrical disconnect switch.
5. Remove or open all panels and check accessible bolts, nuts, screws, terminals and fittings for tightness.
11. Turn on gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be parallel with gas supply line when in “ON” position.
6. Shut off gas supply at manual gas shut off valve in gas supply line (gas models only). Handle of gas shut off valve should be at 90 0 angle to gas supply line when in “OFF” position.
7. Unlock and open service panel and inspect gas connections for evidence of leakage or loose connections.
Page 61 of the Speed Queen JC50CE user manual — SECTION II Installation Instructions
Page 61 · click to enlarge
Page 61
Speed Queen JC50CE — SECTION II Installation Instructions diagram (page 61)
Fig. 33 · SECTION II Installation Instructions
Speed Queen JC50CE — SECTION II Installation Instructions diagram (page 61)
Fig. 34 · SECTION II Installation Instructions
Page 62 of the Speed Queen JC50CE user manual — NOTES
Page 62 · click to enlarge
Page 62

NOTES

Page 63 of the Speed Queen JC50CE user manual — SECTION V Decommissioning Instructions
Page 63 · click to enlarge
Page 63

SECTION V Decommissioning Instructions

1. Turn off electrical supply external to machine.
2. Turn off electrical disconnect on machine.
3. Turn off gas supply external to machine.
4. Turn off manual gas shut-off valve on machine.
5. Turn off steam supply external to machine.
6. Remove all electric, gas and steam connections.
Page 64 of the Speed Queen JC50CE user manual — NOTES
Page 64 · click to enlarge
Page 64

NOTES

Page 65 of the Speed Queen JC50CE user manual — SECTION II Installation Instructions
Page 65 · click to enlarge
Page 65
Page 65 of the Speed Queen JC50CE user manual — SECTION II Installation Instructions
Page 66 of the Speed Queen JC50CE user manual — SECTION II Installation Instructions
Page 66 · click to enlarge
Page 66
Page 66 of the Speed Queen JC50CE user manual — SECTION II Installation Instructions

Ask about the Speed Queen JC50CE

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Speed Queen JC50CE

Be the first to ask — other owners or our team will answer.

Original document

Speed Queen JC50CE manual PDF

66 pages·737 KB·Clothes Dryer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…