Instruction/ maintenance manual of the product SB1044 Southbend
Go to page of 8
Instruction Sheet PHONE: (360) 734-1540 • www.southbendlathe.com M O D E L S B10 4 4 C UT TI N G F L U I D K IT Specifications • Motor ....................................................... 1 ⁄ 8 HP • Phase & Cycle ................. 3-Phase & 50/60 Hz • Voltage .
-2 - Mfg. Since 6 /1 0 Mod el SB 1 044 I NS T R UCT IONS Inst allation During the installation process of your cutting fluid kit, you'll need the following items: F or Power Connection • Apowersourcethatmeetstheminimum circuit requirements for this machine.
Mfg. Since 6 /1 0 Mod el SB 1 0 44 -3- I NS T R UCT IONS Operation Only use high quality water-soluble cutting fluid in this system. Never attempt to pump straight cutting oils or kerosene. If you do, the higher viscosity of the oil will overload the motor, causing damage, or flammable liquids may ignite.
-4- Mfg. Since 6 /1 0 Mod el SB 1 0 44 INS T R UCT IONS Maintenance When you replace the old cutting fluid, take the time to thoroughly clean out both sides of the tank. Make sure to dispose all old fluid according to local regulations. Cutting fluid is considered hazardous waste by the EPA.
Mfg. Since 6 /1 0 Mod el SB 1 0 44 -5- I NS T R UCT IONS T roubleshooting Little or no cutting fluid is being pumped. Pump and motor may also vibrate or be noisy. 1. No power; voltage is incorrect. 1. Switch power supply ON /verify machine and pump voltages match.
-6- Mfg. Since 6 /1 0 Mod el SB 1 0 44 INS T R UCT IONS Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully.
Mfg. Since 6 /1 0 Mod el SB 1 0 44 -7- I NS T R UCT IONS ! AMP THE R MAL RELA Y CONT ACT OR Allen Bradley C094 00 3 5 7 L1 L2 L3 2 4 6 8 T1 T2 T3 T4 95 4 5 6 96 NO NC 97 98 8 O U V W Ground 3 2 1 4 6 .
-8- Mfg. Since 6 /1 0 Mod el SB 1 0 44 INS T R UCT IONS Par ts L ist Par ts Diagram This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase.
An important point after buying a device Southbend SB1044 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Southbend SB1044 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Southbend SB1044 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Southbend SB1044 you will learn all the available features of the product, as well as information on its operation. The information that you get Southbend SB1044 will certainly help you make a decision on the purchase.
If you already are a holder of Southbend SB1044, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Southbend SB1044.
However, one of the most important roles played by the user manual is to help in solving problems with Southbend SB1044. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Southbend SB1044 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
